MUKii TransImp TIP-Q120U3SI User manual

SATA/IDE to USB 3.0 Adapter User’s Manual /使用手冊
MODEL : TIP-Q120U3SI
www.mukii.com.tw
All Registered Trademarks Belong To Their Respective Companies Copyright © 2010 MUKii Technology INC. All Rights Reserved.
S ATA/IDE to US B 3.0 Adapter

01
TABLE OF CONTENTS
目錄
PACKAGE INCLUDES.................................................................................................2
FEATURE / SPECIFICATIONS....................................................................................3
SYSTEM REQUIREMENTS ........................................................................................4
PARTS LAYOUT ..........................................................................................................5
INSTALLATION ............................................................................................................6
M one TUNING SYSTEM INTRODUCTION ...............................................................10
FAQ ............................................................................................................................11
WARRANTY...............................................................................................................12
CONTACT..................................................................................................................12
包裝內附 .....................................................................................................................13
產品特色 / 產品規格 ...................................................................................................14
系統需求 .....................................................................................................................15
裝置介面 .....................................................................................................................16
安裝步驟 .....................................................................................................................17
M one 硬碟調校程式介紹 ...........................................................................................21
問與答 .........................................................................................................................22
授權 / 保證書 .............................................................................................................23
SATA/IDE to USB 3.0 Adapter

SATA/IDE to USB 3.0 Adapter
PACKAGE INCLUDES
TransImp –SATA/IDE to
USB 3.0Adapter
x 1 USB 3.0 Cable
x 1 User’s Manual x 1
4 PIN to SATA Power Cable
x 1
AC PowerAdapter
x 1
02
Please check your packing list to be sure all parts are recieved
SATA/IDE to USB 3.0 Adapter User’sManual /使用手冊
MODEL: TIP-Q120U3SI
www.mukii.com.tw
AllRegistered Trademarks Belong To Their Respective Companies Copyright©2010 MUKii Technology INC. All Rights Reserved.
SATA/IDE to US B 3.0 Adapter
ValueAdded
Software CD
x 1
www.mukii.com.tw
M ONE TUNING SYSTEM INCLUDED
AutoFormat / Smart Energy Saving / USB Turbo / Auto Backup / Status Feedback
M1_V10.0.0_a
SATA Cable
x1
SATA
SATA
B

03
■
Easy Installation with Tool-free Design.
■
Support 2.5”/3.5”IDE/SATAI/II HDD/SATA SSD
■
The Product Supports the Blu-ray Optical Drives and Regular 5.25" SATA/IDE Devices.
■
USB 3.0 Interface for Easy Data Access. Transfer Rates Up to 5Gbps with USB 3.0.
■
Includes a 110V~240V Certified External Power Adapter which Provides Consistent Power
to Your External Device.
■
The Port Features Foolproof Design to Prevent HDD Damage Caused by Incorrect Insertion.
■
Its Separate Power Switch Provides Trouble-free Hardware Protection.
■
Highly Compact and Extremely Portable
■
Hot Swappable : Plug and Play
■
M One Tuning System Included : Auto Format / Smart Energy Saving / USB Turbo / Auto
Backup / Status Feedback.
FEATURE
■ Model : TIP-Q120U3SI
■ Device support : IDE/SATA I/II Hard Drive or SATA SSD
■ Device size : 2.5” / 3.5” / 5.25”
■ Internal interface : USB 3.0
■ Material : Plastic
■ Dimension : 75 x 49 x 13 mm
■ Power : AC Power Adapter
■ Cable : 80cm (31.5 inches)
SPECIFICATIONS
For the most current storage capacity & Operating System Support, please check our website : www.mukii.com.tw
S A TA/ID E to US B 3.0 Adapter
USB 3.0 Cable
SATA/IDE to USB 3.0 Adapter

04
SYSTEM REQUIREMENTS
Intel Pentium II 350 MHz-compatible.
Microsoft Windows 2000/XP/VISTA/7.
1. USB Equipped System
2. For USB 2.0 Speeds, the System Must
Support USB 2.0 Specifications
3. For USB 3.0 Speeds, the System Must
Support USB 3.0 Specifications
4. CD Rom drive
(for value added software)
※USB 3.0 Only Support Windows XP
and Later.
SATA/IDE to USB 3.0 Adapter

05
PARTS LAYOUT
SATA Connector
SATA/IDE to USB 3.0 Adapter
3.5”/5.25” IDE Connector
LED Indicator
USB 3.0 Connector 2.5” IDE Connector

06
INSTALLATION
(Figure A)
(Figure B)
(Figure B)
(Figure C)
(Figure C)
1. Insert 2.5” IDE hard drive (HDD) into the slot.
Turn the front side upward.
2. Make sure that the IDE 2.5” HDD pins align
to the device slot.
3. Connect the USB cable to the USB port on
the PC. Once connected properly, the HDD
should be automatically detected and be
ready for use.
(You might need to connect both USB cables
for adequate power.)
Once the power comsumption of PCIE bus is not
enough, please connect the power connector of
USB cable to the USB 2.0 port of motheroard.
2.5” IDE Hard Drive Installation:
( Figure A )
Don’t connect the 4-pins on the left side to the device.
Computer
IDE 2.5”
Hard Drive
Extra Power
IDE 2.5”
Hard Drive
IDE 2.5”
Hard Drive
SATA/IDE to USB 3.0 Adapter
B
2.5”
B
IDE 2.5”
Hard Drive
TransImp-SATA/IDE
to USB 3.0 Adapter

07
(Figure A)
(Figure B1)
(Figure B2)
( Figure B1.B2 )
( Figure C1.C2 )
(Figure C2)
(Figure C1)
1. Insert 3.5” IDE hard drive into the slot. Turn the
front side upward. (Set the HDD to MASTER if
needed).
2. Connect the larger 40-pin IDE connector of
TransImp-SATA/IDE to USB 3.0 Adapter to
the hard drive.
3. Connect a 4-pin power connector from power
supply to hard drive.
4. Turn on the device power.
5. Connect the USB cable to the USB port on the PC.
Once connected properly, the HDD should be
automatically detected and be ready for use.
3.5” IDE Hard Drive Installation:
( Figure A )
IDE 3.5”
Hard Drive
IDE 2.5”
Hard Drive
SATA/IDE to USB 3.0 Adapter
3.5”/5.5”
OFF
ON
(B2) (B1)
(C2)
(C1)
IDE 3.5” Hard Drive
IDE 3.5”
Hard Drive

08
(Figure A)
(Figure A)
(Figure B)
( Figure B )
( Figure C )
(Figure C)
1. Using a SATAcable, connect one cable header to
your SATAhard drive.
2. Connect the other header to the SATAport of
TransImp-SATA/IDE to USB 3.0 Adapter.
3. Connect Power Cable to PowerAdapter.
4. Connect PowerAdapter to hard drive.
2.5” & 3.5” SATA HDD/SSD installation:
( Figure A )
SATA/IDE to USB 3.0 Adapter
SATA
SATA
SATA
SATA
SATA SATA
SATA
(A2)
(A1)
SATA 2.5” & 3.5” HDD
SATA 2.5”
& 3.5 HDD

09
(Figure D)
(Figure E)
( Figure E )
5. Turn on the power, HDD will begin to spin up.
6. Connect the USB cable to the USB port on the
PC. Once connected properly, the HDD should
be automatically detected and be ready for use.
( Figure D )
SATA/IDE to USB 3.0 Adapter
1. Keep the HDD in a flat position when being used.
2. Make sure Power Adapter Switch has been turned
off before disconnecting the HDD from the Power
Cable.
3. Do NOT touch PCB of the HDD when it is power-on.
4. Never remove, shake or flap the HDD when hard
drive is in use.
NOTE :
OFF
ON
SATA
SATA
SATA
SATA 2.5” & 3.5” HDD

10
M one TUNING SYSTEM INSTALLATION
(Figure A)
(Figure B)
(Figure C)
(Figure D)
(Figure E)
Partition and format your hard drive into one or
two disks, label your disk and setting partition
size as you want.
Boost TransImp external hard disk data transfer
rate.
The unit will be automatically running into
sleeping mode when you stop operating it for
a while.
When you connect MUKii TransImp external
hard disk, you can read the status of your hard
disk situation such as, the brand of HDD,
available disk space, healthy condition.
Auto Backup automatically backup your critical
data from local disk to MUKii TransImp external
hard disk.
( Figure A )
( Figure B )
( Figure C )
( Figure D )
( Figure E )
SATA/IDE to USB 3.0 Adapter
USB Turbo :
Auto Backup :
Auto Format :
Smart Energy Saving :
Status Feedback :
※Please Find Software CD for M ONE TUNING
SYSTEM User’s Manual.

11
FAQ
SATA/IDE to USB 3.0 Adapter
1. When the hard drive is connected, why
couldn't the computer work?
A : The 3.5” IDE or SATA drives need to connect the
power adapter and turn on the power. When the
hard drive works then connect it with the USB cable.
A : You need to format the new hard drive before using it.
Please execute MUKii M one tuning system to start
formating & partition your HDD.
2. Why couldn't the computer detect the new
hard drive ?
A : The format of different system is not the same.
It’s not compatible.
3. Why couldn't the MAC computer use the hard
drive which is formatted by Windows system ?
A : Some NBs and PCs couldn’t supply enough electricity.
We will suggest you to connect the USB port on the
back of PCB.
4. It couldn’t work by connecting one USB cable.

12
SATA/IDE to USB 3.0 Adapter
WARRANTY
CONTACT
The TransImp comes with a One (1) year Limited Warranty (90-day on defective parts). Should your product
become defective within the specified time frame, please visit www.mukii.com.tw to receive instructions for
obtaining repair or warranty exchange. Cosmetic defects and missing parts are not covered by this warranty.
Please check to make sure all parts are included & no visible flaws. If a replacement is required for any
cosmetic defects or missing parts, please contact the retailer from whom you purchased the Product
immediately.
2F,No.588,Tanmei St,Neihu District,Taipei City114,Taiwan(R.O.C)
TEL: [phone] FAX : [phone]
www.mukii.com.tw
MUKii Technology INC.

SATA/IDE to USB 3.0 Adapter
勁速系列-SATA/IDE
to USB 3.0快捷線
x 1
USB 3.0高速傳輸線
x 1
使用說明書
x 1
4-Pin to SATA 電源轉接線
x 1
專用變壓器
x 1
13
SATA/IDE to USB 3.0 Adapter User’sManual /使用手冊
Model: TIP-Q120U3SI
www.mukii.com.tw
AllRegistered Trademarks Belong To Their Respective Companies Copyright © 2010 MUKii Technology INC. All Rights Reserved.
SATA/IDE to US B 3.0 Adapter
增值程式光碟
x 1
www.mukii.com.tw
M ONE TUNING SYSTEM INCLUDED
AutoFormat / Smart Energy Saving / USB Turbo / Auto Backup / Status Feedback
M1_V10.0.0_a
SATA 傳輸線
x1
SATA
SATA
包裝內附
B
請先檢查產品內附是否齊全

14
S A TA/IDE to US B 3.0 Adapter
USB 3.0 高速傳輸線
SATA/IDE to USB 3.0 Adapter
■
簡易安裝設計，不需使用工具拆裝硬碟，迅速好用。
■
支援2.5吋/3.5吋高容量IDE / SATA I/II硬碟/SATA SSD。
■
支援藍光光碟機與一般5.25吋SATA/IDE裝置。
■
透過USB 3.0介面，可輕易連接儲存設備至任何電腦存取資料，最高支援5Gb/s傳輸速度。
■
110V~240V 國際認證電源，讓您免除供電不足的困擾。
■
連接埠具防呆設計，防止插錯導致硬碟損毀。
■
獨立電源開關，保護硬體使用無負擔。
■
隨插即用，支援熱插拔。
■
高質感簡約外型設計，袖珍輕巧攜帶方便。
■
硬碟調校程式:HDD自動分割 / 省電功能 / USB Turbo / 自動備份 / 磁碟資訊回報。
產品特色
產品規格
■
產品型號 ：TIP-Q120U3SI
■
支援裝置 ：IDE/SATA I/II 硬碟 / SATA SSD
■
裝置規格 : 2.5吋/3.5吋/5.25吋
■
傳輸介面 ：USB 3.0
■
外觀材質 ：塑膠
■
本體尺寸 ：75 x 49.5 x 13 mm
■
電 源 ：AC電源接頭
■
線材長度 ：80cm (31.5 inches)
* 最新硬碟容量與作業系統支援請上萌科技網站查詢 : www.mukii.com.tw

15
Intel Pentium II 350 MHz-compatible
Microsoft Windows 2000/XP/VISTA/7
1. 硬體配備支援USB介面
2. USB 2.0傳輸速度，系統須支援USB 2.0規格
3. USB 3.0傳輸速度，系統須支援USB 3.0規格
4. CD Rom 光碟機 (安裝增值程式使用)
※ USB 3.0 只支援 Windows XP 以上系統
SATA/IDE to USB 3.0 Adapter
系統需求

16
SATA/IDE to USB 3.0 Adapter
3.5/5.25吋
IDE裝置連接埠
2.5吋
IDE硬碟連接埠
LED 指示燈
USB 3.0 連接埠
裝置介面
SATA裝置連接埠

17
(圖 B)
(圖 C)
1. 將2.5吋硬碟正面朝上。
2. 將針腳對準勁速系列- SATA/IDE to
USB 3.0快捷線的2.5吋插槽組合。
3. 插入後再把USB線連接電腦。
(部份電腦因USB供電較為不足，可將延伸
USB接頭接上另一個USB埠)
2.5吋IDE硬碟安裝說明 :
(圖 A)
2.5吋有四腳為調整針腳，請勿插入
IDE 2.5”
Hard Drive
IDE 2.5”
Hard Drive
SATA/IDE to USB 3.0 Adapter
B
2.5”
B
IDE 2.5”
Hard Drive
勁速系列-SATA/IDE
to USB 3.0快捷線
IDE 2.5吋硬碟
USB額外供電
電腦
安裝步驟
(圖 A)
(圖 B)
(圖 C)
部分USB 2.0/3.0 PCIE 擴充卡會有供電
不足的困擾，延伸之USB接頭建議連接主
機板上之USB埠。
NOTE :

18
(圖 B1.B2)
(圖 C1.C2)
1. 將3.5吋硬碟正面朝上。
2. 將硬碟插座對準勁速系列- SATA/IDE to
USB 3.0快捷線的3.5吋插槽組合。
3. 將電源供應器上接頭與硬碟組合。
4. 開啟電源開關。
5. 將USB傳輸線連接至電腦的USB傳輸埠，則會
自動偵測到硬碟，並可開始使用。
3.5吋IDE硬碟安裝說明 :
(圖 A)
IDE 2.5”
Hard Drive
SATA/IDE to USB 3.0 Adapter
3.5”/5.5”
OFF
ON
(B2) (B1)
(C2)
(C1)
IDE 3.5” Hard Drive
IDE 3.5”
Hard Drive
IDE 3.5吋硬碟
(圖 A)
(圖 B1)
(圖 B2)
(圖 C1)
(圖 C2)

19
(如圖 B)
(如圖 C)
1. 將SATA傳輸線，連接於SATA硬碟/SSD資料
傳輸埠。
2. SATA傳輸線另一端連接至勁速系列- SATA
/IDE to USB 3.0快捷線SATA傳輸埠。
3. 將電源供應器上的接頭，與SATA電源轉接線
組合。
4. 將組合後的SATA電源轉接線，接於SATA硬碟
電源埠。
SATA 2.5吋 & 3.5吋硬碟/SSD安裝說明 :
(如圖 A1.A2)
SATA/IDE to USB 3.0 Adapter
SATA
SATA
SATA
SATA
SATA SATA
SATA
(A2)
(A1)
SATA 2.5” & 3.5” HDD
SATA 2.5”
& 3.5 HDD
(如圖 A1)
(如圖 A2)
(如圖 B)
(如圖 C)