Mustcam H Series User manual

IP Camera
Quick Start Guide
====================
H Series V3.1

1．Package Contents
IP Camera
5V Power Adaptor
Bracket and Screws
Wi-Fi Antenna
Network Cable
Quick Start Guide
2．Install App
2.1 Download App
iOS: Search and download Mustcam from App Store.
Android: Search and download Mustcam from play.google.com.
2.2 Install App. After installed, click to start it, as follows:
You can click +to add camera for live
video. If there is no camera online,
then please go to Camera page to add
camera online firstly.

3．Configure IP Camera to Network
3.1 Power the IP Camera by using the supplied power adaptor. The camera will
then start and initialize itself by rotating Pan/Tilt one round respectively. The
green LED (at 6-o’clock position) will flash quickly for 90 seconds, waiting for WIFI
configuration.
3.2 Configure the IP Camera to Network. There are 3 ways to do this.
3.2.1 By WIFI (recommended):
After the camera powered and when the green LED flashes quickly (for 90
seconds), click +from Camera page, choose Add a New Camera (by WIFI),
input UID, and input WIFI Network Password, finally click Start Configuring WIFI.
The configuration will finish within 10-50 seconds. And then you can view live
video on app. For more detailed operation, please refer to 4.1.
Note: This configuration should be carried out within 90 seconds when the green
LED still flashes quickly. After the 90 seconds, the green LED light will flash
slowly, waiting for direct connection between Smart Phone and IP Camera (no
need for LAN or Internet).

Direction Connection between Smart Phone and IP Camera:
(1) Change your Smart Phone’s WIFI network to the IP Camera’s SSID.
(2) Then you can configure the IP Camera to other WIFI network. Please refer
to 6.3.
3.2.2 By Net cable:
Connect the IP Camera to router by Net cable. If you need to switch wired
connection to wireless connection, please go to WIFI Config under Advance
Config. Please refer to 6.3.
3.2.3 By WPS
By WPS, user can establish WiFi connection for the IP Camera directly too. This
requires that your router has WPS function. If you are not sure about this, please
refer to your router user manual.
After the camera powered and when its green LED flashes quickly (for 90
seconds), press the WPS button on your router and its WPS light will flash,
waiting for match. Then press the WPS button on your IP Camera for 3 seconds
and release it, IP Camera’s green LED flashes from quickly to slowly, which
indicates that the connection is successful.
If IP Camera or Router powered on and off or restarted, WPS connection should
be configured again.
4．Add IP Camera to App
Choose Camera from the main menu at the bottom, and then enter Camera
management list. Click +at the right corner, to enter the adding camera page.

There are 2 options to add IP Camera.
4.1 Add a New Camera (by WIFI): This enable you to configure an IP Camera
to WIFI Network by WIFI directly, no need by Net cable. The WIFI network of
your Smart phone should be the same as the WIFI network that the camera
will join.
Note: This operation should be carried out when the LED light flashes
quickly (90 seconds) soon after the IP Camera started (or re-started).
UID:
Input the camera UID by typing or Scan QR. The
UID is on the label at the bottom of the Camera.
Network:
This column shows the Smart phone’s current
WIFI network automatically. This network will be
the one that the camera will join. So if it is not the
target network for the camera, please configure
the Smart Phone to that target network firstly.
Password:
Input the password of the WIFI network.
Start Configuring WIFI:
Finally, click this button to start the configuration.
This may takes 10-50 seconds. After that the
camera starts to work.
4.2 Add an Online Camera: This is to add a camera that is already connected
to network (no matter by WIFI or cable).
UID:
Input the camera UID by typing or Scan
QR. The UID is on the label at the bottom
of the Camera.
You can also search online cameras that
are within the same LAN with your Smart
Phone and choose the target camera.
Password:
The default password is 8888. You can
change the password at the Setting page
later.
Finally, click ok to confirm the adding.

5．View Live Video
There are two ways to view live video.
5.1 From the Video page
① ② ③ ④
①Click +, (If there is no camera online, it will shows No online camera, please go
to Camera page to add camera.)
②Choose an online camera.
③Live video is shown in the window.
④You can switch to one window by clicking the □at the right corner.
5.2 From Camera page
Click an online
camera, and then
enter the Live
Video interface.

5.3 Preview Interface Icon Definition
Audio On/Off Cruise (up/down)
Mic On/Off Cruise (left/right)
Snapshot Resolution
Record Video Brightness
Mirror Contrast
Flip Setting
Single Window Four Window
6．Settings
6.1 By clicking , you can enter setting page, functions are as follows:
Modify Camera:
Modify camera
Name/UID/Password.
Delete Camera:
Delete an online camera.
Reconnect:
Connect the camera again.
Advance Config:
Enter into more settings as
follows.

6.2 Advance Config:
Motion Detection Sensitivity: sensitiveness
to trigger the motion detection.
Alarm Interval: interval time for snapshot
Change WIFI network for the IP Camera.
Switch connection from wired to wireless.
Setup record time, resolution and file length.
Setup the Pan/Tilt rotation speed.
Setup the brightness (darkness) to trigger
IR-LED.
Setup the IP Camera date/time.
Change P2P access password.
Reboot the camera.
6.3 Switch Wired to Wireless
WIFI Config enables you to switch the IP Camera connection from one network
to another, or wired to wireless (WIFI). Enter this interface, simply choose a WIFI
Network and input password and then disconnect net cable after 10 seconds.
Note: Please make sure that the target WIFI Network works normally and its
password is correct.

7. View Record Picture & Video
Click Media from the bottom main menu.
Alarm Records:
View pictures captured when alarm
triggered. You can switch different camera
by clicking .
Snapshots Files:
View taken pictures. You can switch different
camera by clicking .
Record Files:
View recorded video clips. You can switch
different camera by clicking .
Camera SDCard Files:
View files on SD card of IP Camera. The
vide file format is .asf. Since the file size is
bigger, it is recommended to download and
play the files on PC.

8. Access the Camera by PC
8.1 Install the software Mustcam IPC Viewer (you can download it from
http://www.mustcam.com/download/) and start it.
User Name: admin
Password: Default password is
8888; you can change the
password from Setting page
later.
8.2 Main Interface

8.3 Add IP Camera
(1) Click to enter Setting page, as follows:
(2) Click +, and there are two ways to add an IP Camera:
①By IP Address: Input the camera’s IP address, port, Username/Password.
② By P2P (recommended): Input UID (on the label at the bottom of the camera)
and P2P Password (8888 by default). If there is both IP and P2P, then IP will be
adopted firstly.
(3) You can also click to search online camera within LAN.
(4) Click OK to confirm the input.
(5) Back to the main interface, choose a target window, and then double-click the
camera from the IP Camera List. Live video will start in that window.

9. Tech Support
For technical issue, please contact us at [e-mail].
For Mustcam IPC Viewer and Search Tool, please download at
http://www.mustcam.com/download.