MYDLINK DCS-8300LH User manual

4
23
1
Plug the included USB Power Adapter into the back of the
camera. Wait until the LED changes from red to blinking orange.
To download and install the mydlink app on your mobile
device, scan the QR code above for your Android or iOS device.
New users: Tap Sign Up to register for a mydlink account,
then tap Add a Device to install your camera.
Existing users: Sign In using your mydlink account and tap
the icon at the top left, then tap Add a Device to start the
setup wizard.
OR
DCS-8300LH
PIN Code: XXXXXX
mydlink No.: XXXXXXX
MAC ID: XXXXXXXXXXXX
H/W Ver.:A1
F/W Ver.:XXX
Endpoint: DCS-8300LH-XXXX
When asked to scan the QR code, use the code found on the
back of the camera.

Full HD Wi-Fi Camera
Quick Start Guide
DCS-8300LH
Minimum Requirements
To install this product, you will need:
• 802.11g/n wireless router
• Internet connection
• A mobile device with Bluetooth 4.0 is required for setup.
• The latest version of the mydlink app from your operating
system’s application store.
• The mydlink app is available for iPhone, iPad and Android™
devices. Please refer to the mobile app's store page to check
whether your device is compatible.
• An e-mail account (required to register for mydlink service)
?
Frequently Asked Questions
1. What is a mydlink account?
To use your mydlink device, you will need to register and sign in to a mydlink
account. Once logged in, you can access your mydlink devices from anywhere
via the Internet and enable features such as cloud recording for cameras.
2. What can I do if my camera is not working properly?
First, reset the camera and try setting the camera up again.
To make sure your hardware is installed correctly, make sure that:
• the power LED is green
• your Internet connection is working
• your router’s wireless is turned on
• your router supports UPnP®
• both your mobile device and camera have a working Internet connection
If your camera is still not working, check your router and make sure it has the
latest firmware.
3. What can I do if I forget my camera password?
If you forget your password, you will need to reset your camera. This process
will change all your settings back to the factory defaults.
To reset your camera, please use an unfolded paperclip to press and hold the
Reset button for at least 10 seconds while your camera is plugged in. Repeat
the setup procedure through the app after the camera reboots and the LED is
blinking orange.
4. Why is there a white haze when viewing in night vision mode?
When viewing in night vision mode, the IR lights on your camera may be
reflecting off a nearby surface. Try repositioning your camera to avoid glare
from IR LEDs.
Notice
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
Version 1.00 (US)_90x130
January 17 2018
Copyright ©2018 All rights reserved. D-Link and the D-Link logo are registered
trademarks of D-Link Corporation or its subsidiaries. Product specifications, size and
shape are subject to change without notice, and actual product appearance may
differ from that depicted on the packaging. Visit dlink.com for more details.
1
2
3
4
6
5
Step 2:
Place the baseplate where you want to position the
camera and use a pencil to mark the holes. You can
use the lower holes for a removable installation, or
the top holes for a fixed one. Make sure that the
arrow on the baseplate is pointing up.
Step 3:
Depending on the material of the wall or ceiling, use
proper tools to drill holes 25mm deep with a 6mm
drill bit where you marked. If the wall is made out of
concrete, drill the holes first, then insert the plastic
anchors to support the screws.
Step 4:
Place the baseplate over the holes that are in the
wall. Make sure to align the baseplate holes with the
holes in the wall. Use the supplied screws to attach
the baseplate to the surface of the wall.
Step 1:
Rotate the baseplate counter-clockwise and remove it.
Step 5:
Place the camera over the baseplate with the
alignment nub pointing left, then attach the camera
by rotating it until the alignment nub points up.
Step 6:
Adjust the angle and rotation of the camera as
desired. You can also rotate the camera on the
baseplate approximately 45° to the right or left.
Support
For manuals and software updates, visit:
support.dlink.com
For technical support, call:
1-877-453-5465
Need help setting up?
Watch the video for step-by-step instructions:
dlinksetup.com
Mounting instructions