MYERS m-6702 (D) User manual

IP NETWORK PA SYSTEM
IP
OWNER'S MANUAL
M-6702 D)
NETWORK AUDIO ADAPTER
Please follow the instructions in this manual to obtain the optimum results from this unit.
We also recommend that you keep this manual handy for future reference.

Contents
1. ............................................................... 1
2.
Front Panel................................................................................ 3
Rear Panel................................. .......................................... 4
3. CONNECTION DIAGRAM................................... .......................... 4
4. ........................................................... 5
5. ........................................................................8
SAFETY PRECAUTIONS
NOMENCLATUREAND FUNCTIONS
......
OPERATIONAND SETTING
SPECIFICATIONS

11
Be sure to read the instructions in this section carefully before use.
Make sure to observe the instructions in this manual as the conventions of safety symbols and messages
regarded as very important precautions are included.
We also recommend you keep this instruction manual handy for future reference.
Safety Symbol and Message Conventions
Safety symbols and messages described below are used in this manual to prevent bodily injury and property
damage which could result from mishandling. Before operating your product, read this manual first and
understand the safety symbols and messages so you are thoroughly aware of the potential safety
Indicates a potentially hazardous situation which, if mishandled, could
result in death or serious personal injury.
Indicates a potentially hazardous situation which, if mishandled, could
result in moderate or minor personal injury, and/or property damage.
When Installing the Unit
Do not expose the unit to rain or an environment
where it may be splashed by water or other liquids,
as doing so may result in fire or electric shock.
Use the unit only with the voltage specified on the
unit. Using a voltage higher than that which is
specified may result in fire or electric shock.
Do not cut, kink, otherwise damage nor modify the
power supply cord. In addition, avoid using the
power cord in close proximity to heaters, and never
place heavy objects -- including the unit itself -- on
the power cord, as doing so may result in fire or
electric shock.
Be sure to replace the unit's terminal cover after
connection completion. Because high voltage is
applied to the speaker terminals, never touch these
terminals to avoid electric shock.
Be sure to ground to the safety ground (earth)
terminal to avoid electric shock. Never ground to a
gas pipe as a catastrophic disaster may result.
Avoid installing or mounting the unit in unstable
locations, such as on a rickety table or a slanted
surface. Doing so may result in the unit falling
down, causing personal injury and/or property
damage.
When the Unit is in Use
Should the following irregularity be found during
use, immediately switch off the power, disconnect
the power supply plug from the AC outlet and
contact your nearest dealer. Make no further
attempt to operate the unit in this condition as this
may cause fire or electric shock.
If you detect smoke or a strange smell coming
from the unit.
If water or any metallic object gets into the unit
If the unit falls, or the unit case breaks
If the power supply cord is damaged (exposure of
the core, disconnection, etc.)
If it is malfunctioning (no tone sounds.)
To prevent a fire or electric shock, never open nor
remove the unit case as there are high voltage
components inside the unit. Refer all servicing to
your nearest dealer.
Myers
Myers
Do not place cups, bowls, or other containers of
liquid or metallic objects on top of the unit. If they
accidentally spill into the unit, this may cause a fire
or electric shock.
Do not insert nor drop metallic objects or
flammable materials in the ventilation slots of the
unit's cover, as this may result in fire or electric
shock.
1. SAFETY PRECAUTIONS

22
An all-pole mains switch with a contact separation of at least 3 mm in each pole shall be incorporated in
the electrical installation of the building.
When Installing the Unit
Never plug in nor remove the power supply plug
with wet hands, as doing so may cause electric
shock.
When unplugging the power supply cord, be sure
to grasp the power supply plug; never pull on the
cord itself. Operating the unit with a damaged
power supply cord may cause a fire or electric
shock.
When moving the unit, be sure to remove its power
supply cord from the wall outlet. Moving the unit
with the power cord connected to the outlet may
cause damage to the power cord, resulting in fire or
electric shock. When removing the power cord, be
sure to hold its plug to pull.
Do not block the ventilation slots in the unit's cover.
Doing so may cause heat to build up inside the unit
and result in fire.
Avoid installing the unit in humid or dusty locations,
in locations exposed to the direct sunlight, near the
heaters, or in locations generating sooty smoke or
steam as doing otherwise may result in fire or
electric shock.
When the Unit is in Use
Do not place heavy objects on the unit as this may
cause it to fall or break which may result in
personal injury and/or property damage. In
addition, the object itself may fall off and cause
injury and/or damage.
Make sure that the volume control is set to
minimum position before power is switched on.
Loud noise produced at high volume when power is
switched on can impair hearing.
Do not operate the unit for an extended period of
time with the sound distorting. This is an indication
of a malfunction, which in turn can cause heat to
generate and result in a fire.
Contact your dealer as to the cleaning. If dust
is allowed to accumulate in the unit over a long
period of time, a fire or damage to the unit may
result.
Myers
If dust accumulates on the power supply plug or in
the wall AC outlet, a fire may result. Clean it
periodically. In addition, insert the plug in the wall
outlet securely.
Switch off the power, and unplug the power supply
plug from the AC outlet for safety purposes when
cleaning or leaving the unit unused for 10 days or
more. Doing otherwise may cause a fire or electric
shock.
SAFETY PRECAUTIONS

MIC
12
3
PUSH
IR VOL+
CALL
CENTER
VOL- TALK
BACK
CALL
CANCEL
OK
7/A-B9
0
/
1A3/B
4/
2/
6/5/
8/
2. NOMENCLATURE AND FUNCTIONS
33
1.
2.
R
3.
4.
5. Confirmation Key
6.
C
Microphone input
Balanced mic input
IR Receiver
eceiving IR signal from IR control
LCD screen:
Numeric buttons
Cancel Key
ancel the setting or operation
functional button
7.
8.
9.
10.
VOL+/VOL Key
Volume up and volume down functional button
CALL
Talk button for announcement
Talk Back
Talk back or intercom communication functional button
Call center
Swift functional button directly connected with
central control room
567
12348109
Front Panel

11. Reserved port
12. RJ45 communication port
13. line input: line input by phoenix connector, like CD, MP3 input
14. line output: line output for extra power amplifier or powered speaker
15. DC INPUT: DC 12V power supply
4
11 12 13 14 15
DC
LINE
OUTPUT
LINE
INTPUT
TERMINAL
LAN IN
CONNECTION DIAGRAM
DC
LINE
OUTPUT
LINE
INTPUT
TERMINAL
LAN IN
POWERED SPEAKER
CD/MP.....
AUDIO SOURCE
LAN SWTICHER
NOMENCLATURE AND FUNCTIONS
Real Panel

4.OPERATION AND SETTING
Connect well the M-6702 D) network paging adapter with software management PC through serial
port TERMINAL click on the START and ALL PROGRAM to open the IP NETWORK
PASYSTEM SOFTWARE , select TERMINAL CONFIGRATION to pop up the window as picture
1, choose the connection way as ERIAL PORT-COM 1 ,then click on ENQUIRY button to pop
up the dialog box enquiry is under taken
Query (if configured terminals) is completed, confirm the correct IP address after the IP address
bar write to set IP address (such as:192.168.1.100),the dialog box appears as shown in Figure 3.
Sure to write the IP address, click "write", write the completeConfirmed that is correct,the dialog
box appears as shown in Figure 4 (terminal configuration will automatically obtain the
physical address of the MAC).
Click "Search"
Click "OK", the connection to the network,and write in the address bar bar in Figure 5 the same IP address
IP , click "Query . "Inquiry is completed, the dialog box appears as shown in Figure 6. The success of the
terminal configuration.
Figure 1. Figure 2.
Figure 3 Figure 4
Figure 5
Figure 6
55
1.

IP network broadcast system settings:
In the "Terminal Configuration", the call to a station IP machine code is set to M-6702 (D) themachine's
call center , press M-6702 D) of the call can be achieved by the piece of dialogue between the two
terminals.
66
OPERATION AND SETTING
2.
3.LCD menu
Press the AFFIRM key interface appears as
follows:
Enter accession number
(host to set a good example: 001)
Press AFFIRM key, the following interface
appears
Press AFFIRM key menu interface appears as
follows:
Enter the menu interface:
4. Talk-back
Select the menu interface, press the intercom
dialing
AFFIRM key interface appears as follows:
Enter number required intercom terminal (PC
software in set good),
Then press the AFFIRM key, can be intercom
Please enter
Return
Return
Login
Return Enter
Function menu options:
1.Dial Intercom
3.Video on Demand
5.Exit Sign
2.Paging speech
4.Play Control
Dial Intercom:
Talkback
*
5.Paging speech:
1
One can enter single or multiple terminals No.
Enter multiple time separated with the # key,
such as input2, # 3,press the AFFIRM key,can
be speech
admin elcome
Return
Return
Paging speech:
Talkback
Return
IP Radio Terminal
Hang up
Paging Connected, please speak…
Area: 2 3
Paging Connected, please speak…
Area: 2
Hang up
Boot, the screen displays the following:
1
Select the menu interface,press the paging
address
AFFIRM key interface appears as follows:
3
1
2
2
4
2

77
OPERATION AND SETTING
6. Video on Demand:
7. Control:
(2)Press the volume keys, the following interface,
Can adjust the volume.
Select the menu interface, playback controls,
according toAFFIRM key, as shown below:
Select the menu interface,
on-demand programming, according toAFFIRM
key has the following interface:
(2)Then AFFIRM key interface appears as follows:
Use up and down select key to select the folder
Any song.
Directory
Enter
1.9
1
9
Up Play
4.Life is a dream
1
Repeat:
0:52
File
VOLUME 52 56
8. Exit Sign:
Opt-out log menu , press the button to return
AFFIRM
To boot interface
(1)
(1)

5. SPECIFICATIONS
88
MODEL
Network Input
Protocol Support TCP/IP,UDP,IGMP
(group broadcasting)
M-6702(D)
Standard Rj45 input
S.N
Audio Format
Sampling Rate
Transmit Speed
Audo Mode
Frequency Output
T.H.D
MP3/MP2
8K~48KHz
10M/100M bps
16 digit stereo CD tone
Sources Voltage Output
Aux Line Voltage Input
Working Tempreture
Working Humidity 10%~90%
Power Supply
200X145X48.5mm
DC12V
0.5Kg
Dimension
N.W
Power Consumption 10W
-20 C~ +60
C
1K
775mv Industrial standard screw terminals
400mv Industrial standard screw terminals
Sources Impedance Output
70dB
0.3%
20Hz~16 K z
H

VersionV0.1
INTELLCETIVE PUBLIC ADDRESS SYSTEM