National Instruments USB-443 Series Manual

CALIBRATION PROCEDURE
NI USB-443x
This document contains information about calibrating the National Instruments USB-4431 and
USB-4432. These devices are referred to in this document as NI USB-443x. For more information about
calibration, visit ni.com/calibration.
Contents
Software Requirements........................................................................................................................ 2
Documentation Requirements.............................................................................................................. 2
Calibration Interval .............................................................................................................................. 2
Test Equipment .................................................................................................................................... 3
Test Conditions .................................................................................................................................... 4
Calibration Procedures......................................................................................................................... 4
Initial Setup.................................................................................................................................. 4
Changing Coupling on NI USB-443x Devices............................................................................ 5
Verification .................................................................................................................................. 6
Analog Input Performance Verification .............................................................................. 6
AI Offset Verification ................................................................................................. 6
AI AC Coupled Gain Accuracy Verification .............................................................. 7
AI DC Coupled Gain Accuracy Verification .............................................................. 8
Analog Output Performance Verification............................................................................ 10
AO Offset Verification for the NI USB-4431 Device ................................................ 10
AO Gain Verification for the NI USB-4431 Device .................................................. 11
Timebase Frequency Accuracy Verification ....................................................................... 12
Adjustment................................................................................................................................... 13
Analog Input Adjustment..................................................................................................... 13
Analog Output Adjustment for the NI USB-4431 Device................................................... 16
Where to Go for Support ..................................................................................................................... 18
ni.com/manuals
DeutschFrançais

NI USB-443x Calibration Procedure 2 ni.com
Software Requirements
Calibrating the NI USB-443xdevice requires installing NI-DAQmx 9.3 or later on the calibration
system. You can download the NI-DAQmx driver from ni.com/downloads. NI-DAQmx supports
conducting a calibration in several programming language application development environments
(ADEs). When you install NI-DAQmx, you only need to install support for the ADE that you intend
to use.
Documentation Requirements
For information about NI-DAQmx and the NI USB-443x, you can consult the following documents:
•DAQ Getting Started guides—provides instructions for installing and configuring NI USB-443x
devices.
•NI-DAQmx C Reference Help—contains the C reference and general information about
measurement concepts.
•NI USB-443x Specifications—provides the published specification values for the NI USB-443x.
Refer to the most recent NI USB-443x Specifications online at ni.com/manuals.
•NI-DAQmx Help—includes information about creating applications that use NI-DAQmx.
These documents are installed with NI-DAQmx. You can also download the latest versions from the
NI Web site at ni.com/manuals.
Calibration Interval
National Instruments recommends a calibration interval of one year for the NI USB-443x. Adjust the
recommended calibration interval based on the measurement accuracy demands of your application.

©National Instruments Corporation 3 NI USB-443x Calibration Procedure
Test Equipment
Table 1 lists the equipment National Instruments recommends for calibrating the NI USB-443x.
If the recommended equipment is not available, select a substitute calibration standard that meets the
given specifications.
Table 1. Recommended Equipment
Equipment Recommended Model
Parameter
Measured/
Adjusted Minimum Requirements
Calibrator Fluke 5700A AI AC Coupled
Gain
AI DC Coupled
Gain
AI Offset
Frequency Range: 1 kHz
Voltage Range: up to 9 Vpk
AC Voltage Accuracy: ± 0.03% at
1kHz
*
DC Voltage Accuracy:
±150 ppm at 9 V
±100 μV with 1 mA load current
Function Generator HP/Agilent 33250A Timebase
Frequency
Accuracy
Frequency Range: up to 10 kHz
Frequency Accuracy: ±5 ppm†
Voltage Range: up to 9 Vpk
Digital Multimeter NI 4071 AO Gain
AO Offset
DC Voltage Resolution: 1 μV
DC Voltage Accuracy at 3.15 V:
±150 ppm
BNC Shorting Cap
NI USB-4431:
quantity 4
NI USB-4432:
quantity 5
Pomona Electronics 5085 AI Offset Resistance: <1 Ω
BNC Cables:
quantity 6
Pomona Electronics 5697 All Characteristic Impedance: 50 Ω
BNC (Female) to
Banana Adapter
Pomona Electronics 1269 All
BNC T-Connectors:
quantity 4
Pomona Electronics 4896 AI Gain
AI Offset
Characteristic Impedance: 50 Ω
*AC accuracy is the sum of all errors, including percent of reading error and temperature error, but excluding percent of
range error.
†Frequency accuracy is the sum of all errors, including initial accuracy and stability errors.

NI USB-443x Calibration Procedure 4 ni.com
Test Conditions
The following setup and environmental conditions are required to ensure the NI USB-443x meets
published specifications:
• Keep connections to the NI USB-443xas short as possible. Long cables and wires act as antennae,
picking up extra noise that can affect measurements.
•Use50ΩBNC coaxial cables for all connections to the device.
• Keep relative humidity between 10% and 80%, noncondensing, or consult the device
documentation for the optimum relative humidity.
• Maintain the ambient temperature between 18 °C and 28 °C, or refer to the device specifications
for the optimum temperature range.
• Allow a warm-up time of at least 30 minutes to ensure that the measurement circuitry of the
NI USB-443xis at a stable operating temperature.
• Allow a warm-up time for all of the instruments and equipment according to the manufacturer
instructions.
Calibration Procedures
The calibration process includes the following steps:
1. Initial Setup—Install the device and configure it in Measurement & Automation Explorer (MAX).
2. Verification—Verify the existing operation of the device. This step confirms whether the device is
operating within the published specifications prior to adjustment.
3. Adjustment—Adjust the calibration constants of the device. The adjustment procedure
automatically stores the calibration date on the EEPROM.
4. Reverification—Repeat the verification procedure to ensure that the device is operating within the
published specifications after adjustment.
Note Skip the AC coupled portion of the AI Offset Verification procedure if both of the following
apply:
• Your device is hardware revision C or earlier.
• You have never performed an analog input calibration adjustment according to this document.
Initial Setup
Refer to the DAQ Getting Started guides for information about how to install the software and hardware
and how to configure the device in MAX.
Note When a device is configured in MAX, it is assigned a device name. Each function call uses
this device name to determine which device to calibrate. This document uses Dev_name to refer to
the device name. In the following procedures, use the device name as it appears in MAX.

©National Instruments Corporation 5 NI USB-443x Calibration Procedure
Changing Coupling on NI USB-443x Devices
NI USB-443xdevices support both AC and DC coupling. After changing the coupling on a device from
DC to AC, wait 30 seconds for the inputs to settle. If samples are acquired before the 30 seconds has
elapsed, the acquired data may be distorted. This section illustrates a deterministic method for setting
the delay.
Figure 1. Implicitly Setting Configuration Settings with the DAQmx Start Task VI
When channel configuration settings are set in software, NI-DAQmx keeps track of the desired settings
and downloads them to hardware simultaneously when the DAQmx Start Task VI is called. This means
that in Figure 1, the settings on the hardware change when the DAQmx Start Task VI is called, and not
when they are set earlier. Therefore, there is no 30 seconds wait between setting the coupling on the
device and starting the acquisition.
For flexibility, NI-DAQmx gives you the ability to download channel configuration settings to hardware
at any point by calling the DAQmx Control Task VI with the commit option as shown in Figure 2. When
programmed this way, the DAQmx Control Task VI ensures that the wait occurs after the coupling
setting has changed on the device.
Figure 2. Explicitly Setting Configuration Settings with the DAQmx Control Task VI
Be sure to perform an explicit commit and wait 30 seconds whenever you change the coupling on an
NI USB-443xfrom DC to AC.
Note NI-DAQmx may initialize the coupling on an NI USB-443xto DC when the device first
powers on. Similarly, NI-DAQmx may set the coupling to DC at the end of the execution of one of
the calibration adjustment VIs. Perform the 30 seconds wait procedure described in this section when
performing an AC-coupled acquisition after the device is powered on, and after calling any of the
calibration adjustment VIs.

NI USB-443x Calibration Procedure 6 ni.com
Verification
This section provides instructions for verifying the NI USB-443x Specifications for gain, offset, and
frequency accuracy. By completing this procedure, you can see how device accuracy has drifted over
time, which helps you determine the appropriate calibration interval for your application.
Note Limits in Tables 3, 4, 6, 8, 9, 11, 13, and 15 are for the specified calibration sample rates and
temperatures, and are based on the March 2011 edition of the NI USB-443x Specifications. For more
general specifications, refer to the most recent NI USB-443x Specifications online at ni.com/
manuals. If a more recent edition of the specifications is available, recalculate the limits based upon
the latest specifications.
Analog Input Performance Verification
This section verifies the analog input (AI) performance of NI USB-443xdevices. Refer to the
NI USB-443x Specifications for the number of channels and performance specifications.
AI Offset Verification
Note Skip the AC coupled portion of this procedure if both of the following apply:
• Your device is hardware revision C or earlier.
• You have never performed an analog input calibration adjustment according to this document.
Complete the following steps to verify the AI offset:
1. Connect a BNC shorting cap to the channel you want to verify on the device.
2. Using Figure 2 as a guide, create and configure an AI voltage task on the NI USB-443xas shown
in Table 2.
3. Acquire readings with the NI USB-443x.
4. Average all of the acquired samples.
Table 2. AI Offset Verification Configuration for NI USB-443x
Configuration Val ue
Minimum value –10.0
Maximum value 10.0
Terminal configuration Pseudodifferential
Acquisition mode Finite number of samples
Rate 102400.0
Samples per channel 65,536
Coupling DC
Physical channel Dev_name/aix*
*Dev_name is the name shown for the NI USB-443xin MAX. xrefers to the channel number.

©National Instruments Corporation 7 NI USB-443x Calibration Procedure
5. If verifying an NI USB-4431, compare the averaged value to the limits in Table 3. If verifying an
NI USB-4432, compare the averaged value to the limits in Table 4.
6. Repeat steps 1 through 5 for each analog input channel that you want to verify. Connect the BNC
shorting cap to the channel being verified in step 1. In step 2, replace aix in the physical channel
parameter with the channel being verified.
NI recommends that you verify each channel, but you can save time by verifying only the channels
used in your application.
7. Repeat steps 1 through 6. In step 2, set the coupling parameter to AC.
Note Skip the AC coupled portion of this procedure if both of the following apply:
• Your device is hardware revision C or earlier.
• You have never performed an analog input calibration adjustment according to this document.
AI AC Coupled Gain Accuracy Verification
Complete the following steps to verify AC coupled gain accuracy:
1. Connect the output of the calibrator to the channel you want to verify on the device.
2. Output a 1 kHz, 6.36 Vrms AC signal from the calibrator.
Table 3. AI Offset Limits for NI USB-4431
Coupling
Device Input Offset
(One Year Limits)
Min (mV) Max (mV)
AC and DC –1.3 1.3
Table 4. AI Offset Limits for NI USB-4432
Coupling
Device Input Offset
(One Year Limits)
Min (mV) Max (mV)
AC and DC –3.2 3.2

NI USB-443x Calibration Procedure 8 ni.com
3. Using Figure 2 as a guide, create and configure an AI voltage task on the NI USB-443xas shown
in Table 5.
4. Acquire readings with the NI USB-443x.
5. Calculate the amplitude of the acquired 1 kHz fundamental tone in Vrms, and compare the
amplitude to the limits in Table 6.
6. Repeat steps 1 through 5 for each analog input channel that you want to verify. Connect the output
of the calibrator to the channel being verified in step 1. In step 3, replace aix in the physical
channel parameter with the channel being verified.
NI recommends that you verify each channel, but you can save time by verifying only the channels
used in your application.
AI DC Coupled Gain Accuracy Verification
Complete the following steps to verify DC coupled gain accuracy:
1. Connect the output of the calibrator to the channel you want to verify on the device.
2. Output 0 VDC from the calibrator.
Table 5. AI AC Coupled Gain Accuracy Verification Configuration for NI USB-443x
Configuration Val ue
Minimum value –10.0
Maximum value 10.0
Terminal configuration Pseudodifferential
Acquisition mode Finite number of samples
Rate 102400.0
Samples per channel 65,536
Coupling AC
Physical channel Dev_name/aix*
*Dev_name is the name shown for the NI USB-443xin MAX. xrefers to the channel number.
Table 6. AI AC Coupled Gain Accuracy Limits for NI USB-443x
Calibrator Output Amplitude (Vrms)
Device Input Amplitude
(One Year Limits)
Min (Vrms)Max (Vrms)
6.36 6.350 6.370

©National Instruments Corporation 9 NI USB-443x Calibration Procedure
3. Create and configure an AI voltage task on the NI USB-443xas shown in Table 7.
4. Acquire readings with the NI USB-443x.
5. Average all of the acquired samples. Record this value.
6. Repeat steps 1 through 5. In step 2, output 9 VDC instead of 0 VDC. Subtract the averaged value
measured for 0 VDC from the 9 VDC measurement.
7. Compare the calculated value to the DC coupled gain accuracy limits.
If verifying an NI USB-4431, compare the calculated value to the appropriate limits in Table 8. If
verifying an NI USB-4432, compare the calculated value to the appropriate limits in Table 9.
8. Repeat steps 1 through 5. In step 2, output –9 VDC instead of 9 VDC. Subtract the averaged value
measured for 0 VDC from the –9 VDC measurement.
Table 7. AI DC Coupled Gain Accuracy Verification Configuration for NI USB-443x
Configuration Val ue
Minimum value –10.0
Maximum value 10.0
Terminal configuration Pseudodifferential
Acquisition mode Finite number of samples
Rate 102400.0
Samples per channel 65,536
Coupling DC
Physical channel Dev_name/aix*
*Dev_name is the name shown for the NI USB-443xin MAX. xrefers to the channel number.
Table 8. AI DC Coupled Gain Accuracy Limits for NI USB-4431
Calibrator Output
Amplitude (VDC)
Device Input Amplitude
(One Year Limits)
Min (V) Max (V)
98.9856 9.0144
–9 –9.0144 –8.9856
Table 9. AI DC Coupled Gain Accuracy Limits for NI USB-4432
Calibrator Output
Amplitude (VDC)
Device Input Amplitude
(One Year Limits)
Min (V) Max (V)
98.982 9.018
–9 –9.018 –8.982

NI USB-443x Calibration Procedure 10 ni.com
9. Compare the calculated value to the DC coupled gain accuracy limits.
If verifying an NI USB-4431, compare the calculated value to the appropriate limits in Table 8. If
verifying an NI USB-4432, compare the calculated value to the appropriate limits in Table 9.
10. Repeat steps 1 through 9 for each analog input channel that you want to verify. Connect the output
of the calibrator to the channel being verified in step 1. In step 3, replace aixin the physical channel
parameter with the channel being verified.
NI recommends that you verify each channel, but you can save time by verifying only the channels
used in your application.
Analog Output Performance Verification
This section verifies the analog output (AO) performance of the NI USB-4431 device. Refer to the
NI USB-443x Specifications for the performance specifications.
AO Offset Verification for the NI USB-4431 Device
Complete the following steps to verify the AO offset:
1. Connect channel AO 0 on the device to the input of the multimeter.
2. Create and configure an AO voltage task on the NI USB-4431 as shown in Table 10.
3. Create an array of length 96,000. Set every element in the array to a value of 0.0. Write the array
to the AO task.
4. Start the AO task. The AO channel will output 0 V as long as the task is running because
regeneration mode is enabled and the task is configured to generate samples continuously.
5. Wait 100 ms. This compensates for the filter delay of the analog output channel.
6. Measure the DC voltage of channel AO 0 on the device using the lowest voltage range of the
multimeter that can measure approximately 100 mV. Record the measured offset, as it will be used
in the AO Gain Verification for the NI USB-4431 Device procedure.
Table 10. AO Offset Verification Configuration for NI USB-4431
Configuration Val ue
Minimum value –3.5
Maximum value 3.5
Terminal configuration Pseudodifferential
Acquisition mode Continuous samples
Rate 96000.0
Samples per channel 96,000
Regeneration mode Allow regeneration
Physical channel Dev_name/ao0*
*Dev_name is the name shown for the NI USB-4431 in MAX.

©National Instruments Corporation 11 NI USB-443x Calibration Procedure
7. Compare the measured voltage value to the AO offset limits in Table 11.
8. Stop and clear the AO task.
AO Gain Verification for the NI USB-4431 Device
Complete the following steps to verify AO gain accuracy:
1. Connect channel AO 0 on the device to the input of the multimeter.
2. Create and configure an AO voltage task on the NI USB-4431 as shown in Table 12.
3. Create an array of length 96,000. Set every element in the array to a value of 3.15. Write the array
to the AO task.
4. Start the AO task. The AO channel will output 3.15 V as long as the task is running, because
regeneration mode is enabled and the task is configured to generate samples continuously.
5. Wait 100 ms. This compensates for the filter delay of the analog output channel.
6. Measure the DC voltage of the analog output channel using the multimeter in the appropriate range
for a 3.5 V amplitude. Subtract the value measured in step 6 of the AO Offset Verification for the
NI USB-4431 Device procedure, and compare this value to the limits in Table 13.
7. Stop and clear the AO task.
Table 11. AO Offset Limits for NI USB-4431
Device Output Offset
(One Year Limits)
Min (mV) Max (mV)
–1.3 1.3
Table 12. AO Gain Verification Configuration for NI USB-4431
Configuration Val ue
Minimum value –3.5
Maximum value 3.5
Terminal configuration Pseudodifferential
Acquisition mode Continuous samples
Rate 96000.0
Samples per channel 96,000
Regeneration mode Allow regeneration
Physical channel Dev_name/ao0*
*Dev_name is the name shown for the NI USB-4431 in MAX.

NI USB-443x Calibration Procedure 12 ni.com
8. Repeat steps 1 through 7. In step 3, set every element in the array to a value of –3.15 instead of
3.15. Compare the result to the limits in Table 13.
Timebase Frequency Accuracy Verification
This section describes the process used to verify the frequency accuracy of the timebase on
NI USB-443xdevices. All analog input and output channels on a single device use the same timebase
circuitry. Therefore, you only need to verify the timebase accuracy on one channel.
Complete the following steps to verify the timebase accuracy:
1. Connect the function generator to the channel being verified on the device.
2. Configure the function generator to generate a 10 kHz sine wave with an amplitude of 9 Vpk and
no DC offset.
3. Create and configure an AI voltage task on the NI USB-443xas shown in Table 14.
4. Acquire readings with the NI USB-443x.
Table 13. AO Gain Limits for NI USB-4431
Device Output Amplitude
(VDC)
Device Input Amplitude
(One Year Limits)
Min (V) Max (V)
3.15 3.1437 3.1563
–3.15 –3.1563 –3.1437
Table 14. Timebase Frequency Accuracy Verification Configuration for NI USB-443x
Configuration Val ue
Minimum value –10.0
Maximum value 10.0
Terminal configuration Pseudodifferential
Acquisition mode Finite number of samples
Rate 40000.0
Samples per channel*2,560,000
Coupling DC
Physical channel Dev_name/aix†
*The read timeout must be greater than 64 seconds.
†Dev_name is the name shown for the NI USB-443xin MAX. xrefers to the channel number.

©National Instruments Corporation 13 NI USB-443x Calibration Procedure
5. Measure the exact frequency of the acquired signal. Compare the detected frequency to the
timebase frequency accuracy limits in Table 15.
Adjustment
Performing the calibration adjustment procedure automatically updates the calibration constants and
date in the EEPROM on the NI USB-443xdevice.
Analog Input Adjustment
Complete the following steps to adjust the analog input of an NI USB-443xdevice.
1. Connect the output of the calibrator to all input channels on the device. Use the BNC T-connectors
to route the signal to all of the inputs.
2. Configure the calibrator to output a 1 kHz signal with a 6.3 Vrms (8.91 Vpk) amplitude.
3. Enable the calibrator output.
4. Using Figure 3 as a guide, commit an AI voltage task on the NI USB-443xwith the settings shown
in Table 16. After the task is committed, clear the task and wait for 30 seconds.
Figure 3. VI Showing How to Prepare a NI USB-443xfor Analog Input Adjustment
Table 15. Timebase Frequency Accuracy Limits for NI USB-443x
Function Generator Output Device Input Frequency
Amplitude (Vpk)Frequency (Hz) Min (Hz) Max (Hz)
9 10000 9999.25 10000.75

NI USB-443x Calibration Procedure 14 ni.com
5. Initialize the AI calibration using the DAQmx Initialize External Calibration VI as shown below.
Note Refer to the NI-DAQmx function parameters for the LabVIEW input values.
6. Perform the AI calibration adjustment by selecting the DAQmx Adjust DSA AI Calibration VI
from the DAQmx Adjust DSA AI Calibration Polymorphic VI as shown below.
7. Disable the calibrator output.
Table 16. AI Adjustment Configuration for NI USB-443x
Configuration Val ue
Minimum value –10.0
Maximum value 10.0
Terminal configuration Pseudodifferential
Acquisition mode Continuous
Rate 1000.0
Coupling AC
Physical channel Dev_name/aix*
*Dev_name is the name shown for the NI USB-443xin MAX. xrefers to the channel number: 0:3 for the
NI USB-4431, and 0:4 for the NI USB-4432.
LabVIEW Block Diagram NI-DAQmx Function Call
Call DAQmxInitExtCal with the following
parameters:
deviceName: Dev_name
password: NI
calHandle: &myCalHandle
LabVIEW Block Diagram NI-DAQmx Function Call
Call DAQmxAdjustDSAAICal with the following
parameters:
calHandle: myCalHandle
referenceVoltage: 6.3
inputsShorted: False

©National Instruments Corporation 15 NI USB-443x Calibration Procedure
8. Configure the calibrator to output 0 V.
Note The Fluke 5700A calibrator must be locked on the 2.2 V range when the output is set to 0 V.
Alternately, you can use a shorting cap instead of the calibrator in step 8 and step 9.
9. Enable the calibrator output.
10. Set the reference voltage to 0 VDC, and call the DAQmx Adjust DSA AI Calibration
Polymorphic VI as shown below.
11. Disable the calibrator output.
12. Finish the AI calibration with the DAQmx Close External Calibration VI as shown below. Use the
action cancel if there has been any error during the AI calibration or if you do not want to save
the new AI calibration constants in the device EEPROM. Use the action commit to save the new
AI calibration constants in the device EEPROM.
The analog input of the device is now calibrated with respect to your external equipment. After
calibrating the device, verify the analog input operation by repeating the Analog Input Performance
Verification section.
LabVIEW Block Diagram NI-DAQmx Function Call
Call DAQmxAdjustDSAAICal with the following
parameters:
calHandle: myCalHandle
referenceVoltage: 0
inputsShorted: True
LabVIEW Block Diagram NI-DAQmx Function Call
Call DAQmxCloseExtCal with the following
parameters:
calHandle: myCalHandle
action: DAQmx_Val_Action_Commit or
DAQmx_Val_Action_Cancel

NI USB-443x Calibration Procedure 16 ni.com
Analog Output Adjustment for the NI USB-4431 Device
Complete the following steps to adjust the analog output of the NI USB-4431 device.
1. Connect channel AO 0 on the device to the multimeter.
2. Initialize the AO calibration using the DAQmx Initialize External Calibration VI as shown below.
3. Create and configure an AO voltage task on the NI USB-4431 as shown in Table 17.
4. Create an array of length 96,000. Set every element in the array to a value of 2.0. Write the array
to the AO task.
5. Start the AO task. The AO channel will output 2.0 V as long as the task is running because
regeneration mode is enabled and the task is configured to generate samples continuously.
6. Wait 100 ms. This compensates for the filter delay of the analog output channel.
7. Measure the DC voltage of channel AO 0 on the device using the multimeter. Record this value as
actualHighVoltage.
8. Stop and clear the AO task.
9. Repeat steps 3 through 8. In step 4, set every element in the array to a value of –2.0 instead of 2.0.
In step 7, record the measured value as actualLowVoltage.
LabVIEW Block Diagram NI-DAQmx Function Call
Call DAQmxInitExtCal with the following
parameters:
deviceName: Dev_name
password: NI
calHandle: &myCalHandle
Table 17. Analog Output Adjustment Configuration for NI USB-4431
Configuration Val ue
Minimum value –3.5
Maximum value 3.5
Terminal configuration Pseudodifferential
Acquisition mode Continuous samples
Rate 96000.0
Samples per channel 96,000
Regeneration mode Allow regeneration
Physical channel Dev_name/ao0*
*Dev_name is the name shown for the NI USB-4431 in MAX.

©National Instruments Corporation 17 NI USB-443x Calibration Procedure
10. Perform AO calibration using the DAQmx Adjust DSA AO Calibration VI as shown below.
11. Finish the AO calibration with the DAQmx Close External Calibration VI as shown below. Use the
action cancel if there has been any error during the AO calibration or if you do not want to save
the new AO calibration constants in the device EEPROM. Use the action commit to save the new
AO calibration constants in the device EEPROM.
The analog output of the device is now calibrated with respect to your external equipment. After
calibrating the device, verify the analog output operation by repeating the Analog Output Performance
Verification section.
LabVIEW Block Diagram NI-DAQmx Function Call
Call DAQmxAdjustDSAAOCal with the following
parameters:
calhandle: myCalHandle
channel: 0
requestedHighVoltage: 2.0
actualHighVoltage: (value from step 7)
requestedLowVoltage: –2.0
actualLowVoltage: (value from step 9)
gainSetting: 0.0
LabVIEW Block Diagram NI-DAQmx Function Call
Call DAQmxCloseExtCal with the following
parameters:
calHandle: myCalHandle
action: DAQmx_Val_Action_Commit or
DAQmx_Val_Action_Cancel

LabVIEW, National Instruments, NI, ni.com, the National Instruments corporate logo, and the Eagle
logo are trademarks of National Instruments Corporation. Refer to the Trademark Information at
ni.com/trademarks for other National Instruments trademarks. Other product and company
names mentioned herein are trademarks or trade names of their respective companies. For patents
covering National Instruments products/technology, refer to the appropriate location: Help»Patents
in your software, the patents.txt file on your media, or the National Instruments Patent Notice
at ni.com/patents. Refer to the Export Compliance Information at ni.com/legal/
export-compliance for the National Instruments global trade compliance policy and how to
obtain relevant HTS codes, ECCNs, and other import/export data.
© 2011 National Instruments Corporation. All rights reserved. 373489A-01 Oct11
Where to Go for Support
The National Instruments Web site is your complete resource for technical support. At ni.com/
support you have access to everything from troubleshooting and application development self-help
resources to email and phone assistance from NI Application Engineers. National Instruments corporate
headquarters is located at 11500 North Mopac Expressway, Austin, Texas, 78759-3504. National
Instruments also has offices located around the world to help address your support needs. For telephone
support in the United States, create your service request at ni.com/support and follow the calling
instructions or dial 512 795 8248. For telephone support outside the United States, visit the Worldwide
Offices section of ni.com/niglobal to access the branch office Web sites, which provide up-to-date
contact information, support phone numbers, email addresses, and current events.