National Instruments PXIe-4480 User manual

Artisan Technology Group is your source for quality
new and certied-used/pre-owned equipment
• FAST SHIPPING AND
DELIVERY
• TENS OF THOUSANDS OF
IN-STOCK ITEMS
• EQUIPMENT DEMOS
• HUNDREDS OF
MANUFACTURERS
SUPPORTED
• LEASING/MONTHLY
RENTALS
• ITAR CERTIFIED
SECURE ASSET SOLUTIONS
SERVICE CENTER REPAIRS
Experienced engineers and technicians on staff
at our full-service, in-house repair center
WE BUY USED EQUIPMENT
Sell your excess, underutilized, and idle used equipment
We also offer credit for buy-backs and trade-ins
www.artisantg.com/WeBuyEquipment
REMOTE INSPECTION
Remotely inspect equipment before purchasing with
our interactive website at www.instraview.com
LOOKING FOR MORE INFORMATION?
Visit us on the web at www.artisantg.com for more
information on price quotations, drivers, technical
specications, manuals, and documentation
Contact us: (888) 88-SOURCE | [e-mail] | www.artisantg.com
SM
View
Instra

GETTING STARTED GUIDE
PXIe-4480/4481
6-Channel, 24-bit, 1.25 MS/s DSA Analog Input
This document explains how to install, configure, and set up the PXIe-4480 and PXIe-4481
Dynamic Signal Acquisition (DSA) analog input modules. Driver support for these modules was
first available in NI-DAQmx 16.1. For a list of devices supported by a specific release, refer to
the NI-DAQmx Readme, available on the version-specific download page or installation media.
Contents
Electromagnetic Compatibility Guidelines .............................................................................. 1
Unpacking the Kit..................................................................................................................... 2
Preparing the Environment.......................................................................................................3
Verifying the Kit Contents ....................................................................................................... 3
Other Equipment............................................................................................................... 3
Installing the Software.............................................................................................................. 4
Installing the Hardware ............................................................................................................ 4
Configuring the Hardware in MAX.......................................................................................... 7
Connecting Signals ................................................................................................................... 8
Connecting RJ50 Cables................................................................................................... 9
Connecting BNC Cables................................................................................................... 9
Connecting mXLR Cables................................................................................................ 10
Environmental Management..................................................................................................... 10
Worldwide Support and Services ............................................................................................. 11
Electromagnetic Compatibility Guidelines
This product was tested and complies with the regulatory requirements and limits for
electromagnetic compatibility (EMC) stated in the product specifications. These requirements
and limits provide reasonable protection against harmful interference when the product is
operated in the intended operational electromagnetic environment.
This product is intended for use in locations with a controlled electromagnetic environment.
However, harmful interference may occur in some installations, when the product is connected
to a peripheral device or test object, or if the product is used in residential or commercial areas.
To minimize interference with radio and television reception and prevent unacceptable
performance degradation, install and use this product in strict accordance with the instructions
in the product documentation.
Furthermore, any modifications to the product not expressly approved by National Instruments
could void your authority to operate it under your local regulatory rules.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

2|ni.com |PXIe-4480/4481 Getting Started Guide
Caution To ensure the specified EMC performance, operate this product only with
shielded cables and accessories.
Caution To ensure the specified EMC performance, the length of all mini-XLR
cables must be no longer than 3 m (10 ft).
Caution Electromagnetic interference can adversely affect the measurement
accuracy of this product when used with BNC cables. The construction of a BNC
coaxial cable is inherently unbalanced in that the outer conductor (LO) is used as a
shield for the inner conductor (HI). However, for functional reasons, there is no input
configuration of the PXIe-4480/4481 that directly connects the LO terminal to the
chassis ground. Without a direct connection to chassis ground, the outer conductor
does not act as a shield for unwanted noise and may act as an antenna for coupling
noise into the module inputs. For single-ended measurements, the noise immunity for
the system can be improved by directly connecting the outer conductor to the chassis
or earth ground at the load end of the cable. For differential measurements, where
such a connection is inherently not possible, the BNC cable can alternatively be
wrapped in a separate grounded shield. In addition, you might need to use snap-on
ferrite beads or other remedial measures to improve electromagnetic compatibility.
Unpacking the Kit
The PXIe-4480/4481 module ships in an antistatic package to prevent electrostatic discharge
from damaging module components.
Caution To prevent electrostatic discharge from damaging the device, ground
yourself using a grounding strap or by holding a grounded object, such as your
computer chassis.
1. Touch the antistatic package to a metal part of the grounded object before removing the
module from package.
2. Remove the module from the package and inspect the module for loose components or any
other sign of damage.
Caution Never touch the exposed pins of connectors.
Store the device in the antistatic package when the device is not in use. Notify NI if the module
appears damaged in any way; do not install a damaged device.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

PXIe-4480/4481 Getting Started Guide |© National Instruments |3
Preparing the Environment
Ensure that the environment in which you are using the PXIe-4480/4481 meets the following
specifications.
Operating ambient temperature ........................ 0 °C to 55 °C
(IEC 60068-2-1, IEC 60068-2-2)
Operating relative humidity.............................. 10% to 90%, noncondensing
(IEC 60068-2-56)
Altitude ............................................................. 2,000 m (800 mbar)
(at 25 °C ambient temperature)
Pollution Degree ............................................... 2
Indoor use only.
Caution Clean the hardware with a soft, nonmetallic brush. Make sure that the
hardware is completely dry and free from contaminants before returning it to service.
Note Refer to the PXIe-4480/4481 Specifications at ni.com/manuals for
complete specifications.
Verifying the Kit Contents
The following items are necessary to set up and use the PXIe-4480/4481:
• PXIe-4480/4481 analog input module
• NI-DAQmx installation media
•PXIe-4480/4481 Getting Started Guide
Note You can download any needed documents from ni.com/manuals.
Other Equipment
Several additional items that are not included in the module kit are necessary to install or operate
the PXIe-4480/4481.
Required Items
• PXI Express chassis and chassis documentation. For more information about compatible
chassis options, refer to ni.com.
• PXI Express embedded controller or MXI-Express (card or built-in) that meets the system
requirements specified in this guide and controller documentation.
• One of the following shielded InfiniBand 12x cables:
– SHB12X-6BNC
– SHB12X-6MXLRM
– SHB12X-6RJ50
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

4|ni.com |PXIe-4480/4481 Getting Started Guide
Note Cables may be shipped with a protective covering on the InfiniBand
connector. Any protective covering or obstruction should be removed before
attempting to secure connection to the PXIe-4480/4481.
Optional Items
•NILabVIEW
Note For the list of LabVIEW versions supported by a specific version of
NI-DAQmx, refer to the NI-DAQmx Readme, available on the version-specific
download page at ni.com/downloads or on the installation media.
Installing the Software
Software support for the PXIe-4480/4481 is provided by NI-DAQmx. For detailed NI software
version support, refer to the NI-DAQmx Readme.
You must be an Administrator to install NI software on your computer.
1. (Optional) If you are developing an NI-DAQmx application, install an ADE, such as
LabVIEW or LabWindows™/CVI™.
2. Install the latest service packs for your operating system.
3. Insert a compatible version of NI-DAQmx. To download the NI-DAQmx driver, visit
ni.com/info and enter the Info Code daqmx.
4. Follow the instructions in the installation prompts.
Note Windows users may see access and security messages during installation.
Accept the prompts to complete the installation. For troubleshooting information,
refer to the Worldwide Support and Services section.
5. When installation completes, select Restart in the dialog box that asks if you want to
restart, shut down, or restart later.
Installing the Hardware
You must install the software before using the hardware.
Caution To prevent damage to the device caused by ESD or contamination, handle
the device using the edges or the metal bracket.
Before you install the hardware, refer to the guidelines in the Maintain Forced-Air Cooling Note
to Users to maintain forced air cooling in the PXI Express system. This document is available at
ni.com/manuals.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

PXIe-4480/4481 Getting Started Guide |© National Instruments |5
1. Ensure the AC power source is connected to the chassis before installing the module. The
AC power cord grounds the chassis and protects it from electrical damage while you install
the module.
2. Make sure the chassis is powered off.
Caution To protect yourself, the chassis, and the module from electrical hazards,
leave the chassis powered off until you finish installing the module.
3. Inspect the slot pins on the chassis backplane for any bends or damage prior to installation.
Do not install a module if the backplane is damaged.
4. Remove the protective plastic covers from all the captive screws on the module front panel.
5. Identify a supported slot in the chassis. The PXIe-4480/4481 module can be placed only in
the supported slot types identified in Table 1. Figure 1 shows the slot type symbols of the
various slot types. Refer to your chassis documentation for more details
Figure 1. PXI/PXIe Chassis Slot Type Symbol Location
6. Touch any metal part on the chassis to discharge any static electricity.
7. Ensure that the injector/ejector handle is in the unlatched (downward) position.
8. Place the module edges into the module guides at the top and bottom of the chassis. Slide
the module into the slot until it is fully inserted.
1 Slot Type Symbols Locations
Table 1. PXIe-4480/4481 Supported Slot Types
PXI Chassis Slot Type Symbol Supported Slot Type Description
PXI Express Peripheral
PXI/PXI Express Hybrid Peripheral
PXI Express System Timing or Peripheral
NI PXIe-1062Q
1
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

6|ni.com |PXIe-4480/4481 Getting Started Guide
Caution When installing the module, make sure both edges are positioned inside
the guides and that the module components do not come into contact with adjacent
modules.
Figure 2. Sliding the PXIe-4480/4481 into the Chassis
9. Latch the module in place by pulling up on the ejector handle.
10. Secure the module front panel to the chassis using the front-panel mounting screws.
Note Tightening the top and bottom mounting screws increases mechanical
stability and also electrically connects the front panel to the chassis, which can
improve the signal quality and electromagnetic performance.
11. Cover all empty slots using filler panels or slot blockers to maximize cooling air flow.
12. Power on the chassis.
1Chassis
2 Hardware Module
3 Injector/Ejector Handle in Down (Unlatched) Position
2
3
1
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

PXIe-4480/4481 Getting Started Guide |© National Instruments |7
Configuring the Hardware in MAX
Use NI Measurement & Automation Explorer (MAX) to configure your National Instruments
hardware. MAX informs other programs about which modules reside in the system and how they
are configured. MAX is automatically installed with NI-DAQmx.
1. Launch MAX.
2. In the Configuration pane, expand Devices and Interfaces to see a list of installed modules.
Installed modules appear under the name of their associated chassis.
Note If you are using the PXIe-4480/4481 with the LabVIEW Real-Time Module,
expand Remote Systems. Find your target IP address or name, expand it, and then
expand Devices and Interfaces.
3. Expand your Chassis tree item. MAX lists all modules installed in the chassis. Your default
module names may vary.
Note If you do not see your hardware listed, press <F5> to refresh the list of
installed modules. If the module is still not listed, power off the system, ensure
the module is correctly installed, and restart.
4. Record the device identifier MAX assigns to the hardware. Use this identifier when
programming the PXIe-4480/4481.
5. Right-click the device and select Self-Test to perform a basic verification of hardware
resources.
6. (Optional) Right-click the device and select Configure to add accessory information and
configure the device.
7. Right-click the device and select Test Panels to test device functionality.
Click Start to test the device functions, and then Stop and Close to exit the test panel.
If the test panel displays an error message, refer to ni.com/support.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

8|ni.com |PXIe-4480/4481 Getting Started Guide
Connecting Signals
The PXIe-4480/4481 front panel has one 73-pin 12x InfiniBand connector. Connect analog input
signals using a shielded InfiniBand 12x cable, as described in the Other Equipment section.
Secure the cable to the module front panel using the cable connector jackscrews.
Note Tightening the top and bottom jackscrews on the InfiniBand connector
increases mechanical stability and improves signal quality and electromagnetic
performance.
Figure 3 shows the front panel connections of the PXIe-4480 and PXIe-4481 modules.
Figure 3. PXIe-4480/4481 Front Panel
1 Top Module
Mounting Screw
2LEDs
3PFI
4 Chassis Ground
5AI0-5
6 Bottom Module
Mounting Screw
PXIe-4481
PXIe-4481
DSA 6 Ch AI
ACCESS ACTIVE
PFI 0
AI 0–5
PXIe-4480
PXIe-4480
DSA 6 Ch AI
ACCESS ACTIVE
PFI 0
AI 0–5
G1
G2
G3
G4
G5
G6
G7
G8
G9
G10
G11
G12
G13
G14
G15
G16
G17
G18
G19
G20
G21
G22
G23
G24
G25
AI 0 +
AI 0 –
AI 1 +
AI 1 –
AI 2 +
AI 2 –
AI 3+
AI 3–
AI 4 +
AI 4 –
AI 5 +
AI 5 –
S1
S2
S3
S4
S5
S6
S7S8
S9S10
S11S12
S13
S14
S15
S16
S17
S18
S19
S20
S21
S22
S23
S24
S25
S26
S27
S28
S29
S30
S31
S32
S33
S34
S35
S36
S37
S38
S39
S40
S41
S42
S43
S44
S45
S46
S47
S48
EX 0 +
EX 2 +
EX 3+
EX 4 +
EX 5 +
EX 1 +
EX 0 GND
EX 1 GND
EX 2 GND
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
EX 3GND
EX 4 GND
EX 5 GND
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVEDRESERVED
GND– –
GND– –
GND– –
GND– –
GND– –
GND– –
GND– –
GND– –
GND– –
GND– –
GND– –
GND– –
GND– –
GND– –
GND– –
GND– –
GND– –
GND– –
GND– –
GND– –
GND– –
GND– –
GND– –
GND
– –
GND– –
G1
G2
G3
G4
G5
G6
G7
G8
G9
G10
G11
G12
G13
G14
G15
G16
G17
G18
G19
G20
G21
G22
G23
G24
G25
AI 0 +
AI 0 –
AI 1 +
AI 1 –
AI 2 +
AI 2 –
AI 3+
AI 3–
AI 4 +
AI 4 –
AI 5 +
AI 5 –
S1
S2
S3
S4
S5
S6
S7S8
S9S10
S11
S12
S13
S14
S15
S16
S17
S18
S19
S20
S21
S22
S23
S24
S25
S26
S27
S28
S29
S30
S31
S32
S33
S34
S35
S36
S37
S38
S39
S40
S41
S42
S43
S44
S45
S46
S47
S48
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVED
RESERVEDRESERVED
GND– –
GND– –
GND– –
GND– –
GND– –
GND– –
GND– –
GND– –
GND– –
GND– –
GND– –
GND– –
GND– –
GND– –
GND– –
GND– –
GND– –
GND– –
GND– –
GND– –
GND– –
GND– –
GND– –
GND– –
GND– –
1
2
6
5
4
3
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

PXIe-4480/4481 Getting Started Guide |© National Instruments |9
Note Refer to the PXIe-4480/4481 Specifications for information about the
operating input range and overvoltage protection.
Connecting RJ50 Cables
The SHB12X-6RJ50 shielded InfiniBand 12x cable provides six RJ50 (10-pin) inputs. Refer to
Table 2 for signal names and descriptions, and the correlation to the pin numbers of the RJ50
modular plug.
Connecting BNC Cables
The SHB12X-6BNC shielded InfiniBand 12x cable provides six BNC inputs. Refer to Table for
signal names and descriptions, and the correlation to the pin numbers of the BNC plug.
Table 2. RJ50 Connector Pin Assignments
RJ50 Modular Plug
Pin Number Diagram Pin Signal Name Signal Description
1NC No connect
2AI+ Positive analog input signal (0 to 5)
3AI- Negative analog input signal (0 to 5)
4NC —
5NC —
6EX+ Positive excitation (0 to 5)
7EX GND Excitation ground (0 to 5)
8NC —
9GND Ground
10 NC —
Shell GND Ground
Table 3. BNC Connector Pin Assignments
BNC Connector Pin
Diagram Pin Signal Name Signal Description
1AI+ Positive analog input signal (0 to 5)
2AI- Negative analog input signal (0 to 5)
10
1
2
1
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

10 |ni.com |PXIe-4480/4481 Getting Started Guide
Connecting mXLR Cables
The SHB12X-6MXLRM shielded InfiniBand 12x cable provides six mXLR inputs. Refer to
Table for signal names and descriptions, and the correlation to the pin numbers of the mXLR
plug.
Environmental Management
NI is committed to designing and manufacturing products in an environmentally responsible
manner. NI recognizes that eliminating certain hazardous substances from our products is
beneficial to the environment and to NI customers.
For additional environmental information, refer to the Minimize Our Environmental Impact
web page at ni.com/environment. This page contains the environmental regulations and
directives with which NI complies, as well as other environmental information not included
in this document.
Waste Electrical and Electronic Equipment (WEEE)
EU Customers At the end of the product life cycle, all products must be sent to
a WEEE recycling center. For more information about WEEE recycling centers,
National Instruments WEEE initiatives, and compliance with WEEE Directive
2002/96/EC on Waste and Electronic Equipment, visit ni.com/environment/
weee.
Table 4. mXLR Connector Pin Assignments
mXLR (Male)
Connector Pin
Diagram Pin
Signal
Name Signal Description
1GND Chassis ground
2AI+ Positive analog input signal (0 to 5)
3AI- Negative analog input signal (0 to 5)
Shell GND Chassis ground
13
2
⬉ᄤֵᙃѻક∵ᶧ᥻ࠊㅵ⧚ࡲ⊩ ˄Ё೑ RoHS˅
Ё೑ᅶ᠋ National Instruments ヺড়Ё೑⬉ᄤֵᙃѻકЁ䰤ࠊՓ⫼ᶤѯ᳝ᆇ⠽䋼ᣛҸ
(RoHS)DŽ݇Ѣ National Instruments Ё೑ RoHS ড়㾘ᗻֵᙃˈ䇋ⱏᔩ ni.com/
environment/rohs_chinaDŽ(For information about China RoHS compliance,
go to ni.com/environment/rohs_china.)
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

PXIe-4480/4481 Getting Started Guide |© National Instruments |11
Worldwide Support and Services
The NI website is your complete resource for technical support. At ni.com/support you have
access to everything from troubleshooting and application development self-help resources to
email and phone assistance from NI Application Engineers.
Visit ni.com/services for NI Factory Installation Services, repairs, extended warranty, and
other services.
Visit ni.com/register to register your NI product. Product registration facilitates technical
support and ensures that you receive important information updates from NI.
A Declaration of Conformity (DoC) is our claim of compliance with the Council of the European
Communities using the manufacturer’s declaration of conformity. This system affords the user
protection for electromagnetic compatibility (EMC) and product safety. You can obtain the DoC
for your product by visiting ni.com/certification. If your product supports calibration,
you can obtain the calibration certificate for your product at ni.com/calibration.
NI corporate headquarters is located at 11500 North Mopac Expressway, Austin, Texas,
78759-3504. NI also has offices located around the world. For telephone support in the United
States, create your service request at ni.com/support or dial 1 866 ASK MYNI (275 6964).
For telephone support outside the United States, visit the Worldwide Offices section of
ni.com/niglobal to access the branch office websites, which provide up-to-date contact
information, support phone numbers, email addresses, and current events.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

© 2016 National Instruments. All rights reserved.
376249B-01 Oct16
Refer to the NI Trademarks and Logo Guidelines at ni.com/trademarks for more information on NI trademarks. Other product and company
names mentioned herein are trademarks or trade names of their respective companies. For patents covering NI products/technology, refer to the
appropriate location: Help»Patents in your software, the patents.txt file on your media, or the National Instruments Patents Notice at
ni.com/patents. You can find information about end-user license agreements (EULAs) and third-party legal notices in the readme file for your
NI product. Refer to the Export Compliance Information at ni.com/legal/export-compliance for the NI global trade compliance policy
and how to obtain relevant HTS codes, ECCNs, and other import/export data. NI MAKES NO EXPRESS OR IMPLIED WARRANTIES AS TO THE
ACCURACY OF THE INFORMATION CONTAINED HEREIN AND SHALL NOT BE LIABLE FOR ANY ERRORS. U.S. Government Customers: The data
contained in this manual was developed at private expense and is subject to the applicable limited rights and restricted data rights as set forth in
FAR 52.227-14, DFAR 252.227-7014, and DFAR 252.227-7015.
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Artisan Technology Group is your source for quality
new and certied-used/pre-owned equipment
• FAST SHIPPING AND
DELIVERY
• TENS OF THOUSANDS OF
IN-STOCK ITEMS
• EQUIPMENT DEMOS
• HUNDREDS OF
MANUFACTURERS
SUPPORTED
• LEASING/MONTHLY
RENTALS
• ITAR CERTIFIED
SECURE ASSET SOLUTIONS
SERVICE CENTER REPAIRS
Experienced engineers and technicians on staff
at our full-service, in-house repair center
WE BUY USED EQUIPMENT
Sell your excess, underutilized, and idle used equipment
We also offer credit for buy-backs and trade-ins
www.artisantg.com/WeBuyEquipment
REMOTE INSPECTION
Remotely inspect equipment before purchasing with
our interactive website at www.instraview.com
LOOKING FOR MORE INFORMATION?
Visit us on the web at www.artisantg.com for more
information on price quotations, drivers, technical
specications, manuals, and documentation
Contact us: (888) 88-SOURCE | [e-mail] | www.artisantg.com
SM
View
Instra