National Instruments SCXI SCXI-1102 Manual

CALIBRATION PROCEDURE
SCXI -1102/B/C
For NI-DAQmx
This document contains information and instructions for calibrating the
National Instruments SCXI-1102/B/C signal conditioning module.
Contents
Conventions ............................................................................................ 2
Software .................................................................................................. 2
Documentation ........................................................................................ 3
Calibration Interval ................................................................................. 3
Password ................................................................................................. 3
Test Equipment ....................................................................................... 4
Test Conditions ....................................................................................... 4
Calibration Process ................................................................................. 5
Initial Setup...................................................................................... 5
Verification Procedure ..................................................................... 7
Adjustment Procedure...................................................................... 12
Verifying Adjusted Values .............................................................. 14
Test Limits .............................................................................................. 14
Gain and Offset................................................................................ 15
SCXI-1102/B/C Front and Rear Panel Diagrams ................................... 15
World Wide Support and Services.......................................................... 18
™

SCXI-1102/B/C Calibration Procedure 2 ni.com
Conventions
The following conventions are used in this document:
»The »symbol leads you through nested menu items and dialog box options
to a final action. The sequence File»Page Setup»Options directs you to
pull down the File menu, select the Page Setup item, and select Options
from the last dialog box.
This icon denotes a note, which alerts you to important information.
bold Bold text denotes items that you must select or click in the software, such
as menu items and dialog box options. Bold text also denotes parameter
names.
italic Italic text denotes variables, emphasis, a cross-reference, or an introduction
to a key concept. Italic text also denotes text that is a placeholder for a word
or value that you must supply.
monospace Text in this font denotes text or characters that you should enter from the
keyboard, sections of code, programming examples, and syntax examples.
This font is also used for the proper names of disk drives, paths, directories,
programs, subprograms, subroutines, device names, functions, operations,
variables, filenames, and extensions.
monospace italic Italic text in this font denotes text that is a placeholder for a word or value
that you must supply.
Software
The SCXI-1102/B/C calibration procedure requires the NI-DAQmx driver.
NI recommends using the latest driver that supports both your development
environment and the SCXI-1102/B/C. NI-DAQmx includes high-level
function calls to simplify the task of writing software to calibrate devices.
NI-DAQmx supports many programming languages, including LabVIEW,
LabWindows™/CVI™, C/C++, C#, and Visual Basic .NET.

©National Instruments 3 SCXI-1102/B/C Calibration Procedure
Documentation
The following documents are the primary references for writing your
calibration utility:
• The NI-DAQmx Help includes information about creating applications
that use NI-DAQmx.
• The NI-DAQmx C Reference Help includes information about the
functions in NI-DAQmx.
• The DAQ Getting Started guides include information about installing
and configuring NI-DAQmx devices.
You can access these documents by selecting
Start»All Programs»National Instruments»NI-DAQmx after installing
NI-DAQmx.
For more information about the SCXI-1102/B/C, refer to the
SCXI-1102/B/C User Manual. For information about installing and
configuring SCXI modules, refer to the SCXI Quick Start Guide.
Calibration Interval
Calibrate the SCXI-1102/B/C at a regular interval as defined by the
measurement accuracy requirements of your application. NI recommends
that you perform a complete calibration at least once every year. You can
shorten this interval based on the accuracy requirements of your
application.
Password
The default password for password-protected operations is NI.

SCXI-1102/B/C Calibration Procedure 4 ni.com
Test Equipment
NI recommends that you use the equipment in Table 1 to calibrate the
SCXI-1102/B/C. If these instruments are not available, use the
requirements listed in Table 1 to select a suitable substitute.
Test Conditions
Follow these guidelines to optimize the connections and the environment
during calibration:
• Keep connections to the SCXI-1102/B/C as short as possible. Long
cables and wires can act as antennas, picking up extra noise and
thermal offsets that affect measurements.
• Use shielded copper wire for all cable connections to the
SCXI-1102/B/C. Use twisted-pair wire to eliminate noise and thermal
offsets.
• Maintain the ambient temperature between 18 °C and 28 °C.
• Keep relative humidity below 80%.
• Allow a warm-up time of at least 15 minutes for the SCXI-1102/B/C
and 30 minutes for the DAQ device to ensure that the measurement
circuitry is at a stable operating temperature.
Table 1. Test Equipment
Equipment
Recommended
Model Requirements
Calibrator Fluke 5700A 50 ppm
DAQ Device NI 6281 16-bit minimum
DMM NI 4070 6 1/2 digit, 15 ppm
Terminal Block SCXI-1300 —

©National Instruments 5 SCXI-1102/B/C Calibration Procedure
Calibration Process
The calibration process has the following steps:
1. Initial Setup—Configure the SCXI-1102/B/C for calibration.
2. Verification Procedure—Verify the existing operation of the
SCXI-1102/B/C. This step determines whether the SCXI-1102/B/C is
operating within its test limits.
3. Adjustment Procedure—Perform an external calibration that adjusts
the SCXI-1102/B/C calibration constants with respect to a known
voltage source.
4. Verifying Adjusted Values—Perform another verification to ensure
that the SCXI-1102/B/C is operating within its test limits after
adjustments.
Initial Setup
Complete the following steps to configure the SCXI-1102/B/C for
calibration:
1. Make sure that all the appropriate driver and application software is
installed.
2. Make sure all components involved in the calibration procedure are
powered off.
3. Assemble the SCXI-1102/B/C, SCXI chassis, terminal blocks, and
DAQ device as shown in Figure 1. You must cable the SCXI-1102/B/C
directly to the DAQ device.

SCXI-1102/B/C Calibration Procedure 6 ni.com
Figure 1. Calibration Connections
4. Power on the SCXI chassis and the external computer.
5. You must configure the hardware properly with Measurement &
Automation Explorer (MAX). Refer to the SCXI Quick Start Guide for
details about configuring the SCXI chassis.
Note When you configure a device in MAX, the device is assigned a device identifier. In
this calibration document, the functions used for demonstrating the calibration process use
the device identifiers Dev1 for the DAQ device and SC1Mod1 for the SCXI-1102/B/C.
1 SCXI-1300 Terminal Block
2 SCXI-1102/B/C Module
3 SCXI Chassis
4 SCXI-1349 Cable Adapter
5 Shielded 68-Pin Cable
6 NB1 Cable (50-Pin Ribbon Cable)
7 TBX 50-Pin Terminal Block
8 Cable to DMM
9 Cable to Calibrator
10 Calibrator
11 DMM
12 DAQ Device
®
5
4
3
2
1
ADDRESS
SCXI1100
2468 10 12 1416 18 20 20 24 26 28 30 32 34 36 38 40 42 44 46 48 50
13 5 7 911 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49
3
1
2
4
5
7
8
11
6
9
12
10

©National Instruments 7 SCXI-1102/B/C Calibration Procedure
Verification Procedure
The verification procedure determines how well the SCXI-1102/B/C is
meeting its test limits. You can use this information to select the
appropriate calibration interval for your application.
The SCXI-1102/B/C stores gain and offset calibration constants for each
gain setting per analog input channel. A complete verification of the inputs
involves measuring the accuracy at all possible gain settings on all channels
of the SCXI-1102/B/C.
To view the calibration VIs in LabVIEW, select Measurement
I/O»DAQmx - Data Acquisition»DAQmx Advanced»DAQmx
Calibration on the Functions palette. You can also use the Search button,
shown in Figure 2, to look for a specific VI.
Figure 2. DAQmx Calibration Palette and the Search Button

SCXI-1102/B/C Calibration Procedure 8 ni.com
Complete the following steps to verify the accuracy of each
SCXI-1102/B/C analog input channel:
1. Use the DAQmx Self Calibrate VI to verify the DAQ device. This VI
measures the onboard reference voltage of the DAQ device and adjusts
the self-calibration constants to account for any errors caused by
short-term fluctuations in the operating environment.
Note Throughout the verification procedure, refer to the function call parameters for the
LabVIEW input values.
2. Connect the calibrator output to pins AI– and AI+ for all channels.
Refer to the SCXI-1300/1301 Terminal Block Installation Guide for
connection instructions. If you are not using the recommended
SCXI-1300, refer to Table 8 for the front signal pin assignments of the
SCXI-1102/B/C. If the calibration signal source is floating, connect
AI – to the SCXI chassis ground using the ground lug available on the
SCXI terminal block.
3. Set the calibrator voltage to the desired test point indicated in
Tables 6 or 7.
4. Create a task using DAQmxCreateTask.
LabVIEW Block Diagram NI-DAQmx Function Call
Call DAQmxSelfCal with the
following parameter:
Device_Name:"Dev1"
LabVIEW Block Diagram NI-DAQmx Function Call
LabVIEW does not require
this step.
Call DAQmxCreateTask with the
following parameters:
taskName: "AIVerificationTask"
taskHandle: &taskHandle

©National Instruments 9 SCXI-1102/B/C Calibration Procedure
5. Add a voltage channel using the DAQmx Create Virtual Channel VI.
6. Set the gain value to 1 or 100 using the DAQmx Channel Property
Node. You can find the AI.Gain property by selecting Analog
Input»General Properties»Advanced»Gain. Use the gain setting
that corresponds to the current test point.
LabVIEW Block Diagram NI-DAQmx Function Call
Call DAQmxCreateAIVoltageChan with the
following parameters:
taskHandle: taskHandle
physicalChannel: "SC1Mod1/aiX"†
nameToAssignToChannel: "myVoltageChannel"
terminalConfig: DAQmx_Val_Cfg_Default
minVal: -10 V
maxVal: 10 V
units: DAQmx_Val_Volts
customScaleName: ""
†Where Xrefers to the channel you are verifying.
LabVIEW Block Diagram NI-DAQmx Function Call
Call DAQmxSetAIGain with the following
parameters:
taskHandle: taskHandle
Channel: ""
Data: (gain value for particular test
point) float64

SCXI-1102/B/C Calibration Procedure 10 ni.com
7. Configure timing for the voltage acquisition using the DAQmx
Timing VI.
8. Commit the verification changes using the DAQmx Control Task VI.
9. For each new test point, use the Time Delay Express VI to account for
the settling time of the SCXI-1102/B/C. Refer to Table 2 for the
settling time of the SCXI-1102/B/C.
LabVIEW Block Diagram NI-DAQmx Function Call
Call DAQmxCfgSampClkTiming with the following
parameters:
taskHandle: taskHandle
source: ""
rate: 1000.0
activeEdge: DAQmx_Val_Rising
sampleMode: DAQmx_Val_FiniteSamps
sampsPerChan: 1000
LabVIEW Block Diagram NI-DAQmx Function Call
Call DAQmxTaskControl with the following
parameters:
taskHandle: taskHandle
action: DAQmx_Val_Task_Commit
Table 2. Settling Time of the SCXI-1102/B/C
SCXI-1102 SCXI-1102B, SCXI-1102C
3 minutes (first test point)
1 minute (all other test points)
5 second
LabVIEW Block Diagram Function Call
Call a sleep or wait function to suspend
execution for the necessary settling time listed
in Table 2.

©National Instruments 11 SCXI-1102/B/C Calibration Procedure
10. Acquire 1000 points of voltage data using the Analog 1D DBL 1Chan
NSamp instance of the DAQmx Read VI.
11. Compute the mean of the 1000 voltage values that you acquired.
12. Compare the resulting average to the upper and lower limits listed in
Tables 6 or 7. If the result is between the upper and lower limits, the
SCXI-1102/B/C passes the test.
13. Clear the acquisition using the DAQmx Clear Task VI.
14. Repeat steps 4 through 13 for the remaining channels.
15. Repeat steps 3 through 14 for all test points in Tables 6 or 7.
You have finished verifying the analog input accuracy of the
SCXI-1102/B/C.
LabVIEW Block Diagram NI-DAQmx Function Call
Call DAQmxReadAnalogF64 with the following
parameters:
taskHandle: taskHandle
numSampsPerChan: –1
timeout: 10.0
fillMode: DAQmx_Val_GroupByChannel
readArray: data
arraySizeInSamples: 1000
sampsPerChanRead: &read
reserved: NULL
LabVIEW Block Diagram NI-DAQmx Function Call
Call DAQmxClearTask with
the following parameter:
taskHandle: taskHandle

SCXI-1102/B/C Calibration Procedure 12 ni.com
Adjustment Procedure
The adjustment procedure adjusts the gain and offset calibration constants
on the SCXI-1102/B/C. Complete the Verification Procedure prior to the
adjustment procedure to determine the pre-calibration accuracy and
whether adjustments are necessary.
Complete the following steps to adjust the gain and offset of the
SCXI-1102/B/C:
1. Connect the calibrator output pins AI- and AI+ for all channels. Refer
to the SCXI-1300/1301 Terminal Block Installation Guide for
connection instructions. If you are not using the recommended
SCXI-1300, refer to Table 8 for the front signal pin assignments of the
SCXI-1102/B/C. If the calibration signal source is floating, connect
AI- to the SCXI chassis ground using the ground lug available on the
SCXI terminal block.
2. Connect the DMM to CH 0+ and CH 0- (pin 3 and 4) on the rear
connector. Refer to Table 9 for the rear signal pin assignments of the
SCXI-1102/B/C.
Note You can access these pins using a 50-pin cable connected to an SCXI-1349.
3. Start an external calibration session using the DAQmx Initialize
External Calibration VI.
Note Throughout the adjustment procedure, refer to the function call parameters for the
LabVIEW input values.
LabVIEW Block Diagram NI-DAQmx Function Call
Call DAQmxInitExtCal with the following
parameters:
deviceName: "SC1Mod1"
password: "NI"
calHandle: &calHandle

©National Instruments 13 SCXI-1102/B/C Calibration Procedure
4. Set the SCXI-1102/B/C to a gain value of 1 or 100 using the DAQmx
Setup SCXI Calibration VI.
5. Set the calibrator to the desired voltage for the gain value you set in the
previous step. Refer to Table 3 or 4 for appropriate voltage set points.
6. Wait for the settling time to elapse and then record the measured output
from the DMM. Refer to Table 5 for the settling time of the
SCXI-1102/B/C.
LabVIEW Block Diagram NI-DAQmx Function Call
Call DAQmxSetup1102Cal with the following
parameters:
calHandle: calHandle
channelNames: "SC1Mod1/aiX"†
gain: 1or 100
†Where Xrefers to the channel you are calibrating.
Table 3. SCXI-1102 Voltage Set Points
Gain Set Points (V)
1 –9 –6 –2 0 2 6 9
100 –0.09 –0.06 –0.02 0.00 0.02 0.06 0.09
Table 4. SCXI-1102 B and SCXI-1102 C Voltage Set Points
Gain Set Points (V)
1 –9 –6 –3 0 3 6 9
100 –0.09 –0.06 –0.03 0.00 0.03 0.06 0.09
Table 5. Settling Time of the SCXI-1102/B/C
SCXI-1102 SCXI-1102B, SCXI-1102C
60 seconds 5 second

SCXI-1102/B/C Calibration Procedure 14 ni.com
7. Adjust the external calibration constants using the DAQmx Adjust
SCXI Calibration VI.
8. Repeat steps 5 through 7 for the seven voltage test points at the current
gain value in Table 3 or 4.
9. Commit the calibration changes you made in the session using the
DAQmx Close External Calibration VI. The data is written to the
hardware in this step.
10. Repeat steps 3 through 9 for both gain values in Table 3.
11. Repeat steps 1 through 10 for the remaining channels.
You have finished adjusting the gain and offset of the SCXI-1102/B/C.
Verifying Adjusted Values
After calibrating the SCXI-1102/B/C, NI recommends that you verify the
analog input operation by repeating the steps listed in the Verification
Procedure to ensure that the SCXI-1102/B/C is operating within its test
limits.
Test Limits
Refer to the SCXI-1102/B/C User Manual for the specifications of the
SCXI-1102/B/C.
LabVIEW Block Diagram NI-DAQmx Function Call
Call DAQmxAdjust1102Cal with the
following parameters:
calHandle: calHandle
refVoltage: (calibrator output
voltage) float64
measOutput: (voltage measured by
DMM) float64
LabVIEW Block Diagram NI-DAQmx Function Call
Call DAQmxCloseExtCal with the following
parameters:
calHandle: calHandle
action: DAQmx_Val_Action_Commit

©National Instruments 15 SCXI-1102/B/C Calibration Procedure
Gain and Offset
Table 6 contains the test limits to use when verifying and adjusting the gain
and offset of the SCXI-1102 and SCXI-1102B. Table 7 contains the test
limits to use when verifying and adjusting the gain and offset of the
SCXI-1102C. If the SCXI-1102/B/C was calibrated within the last year, the
test point value should fall between the Lower Limit and Upper Limit
values found in Tables 6 or 7.
Note The values in Tables 6 and 7 do not include DAQ device errors.
SCXI-1102/B/C Front and Rear Panel Diagrams
Table 8 shows the pin assignments for the SCXI-1102/B/C front panel
connector. Table 9 shows the pin assignments for the SCXI-1102/B/C rear
signal connector.
Table 6. SCXI-1102 and SCXI-1102 B Test Limits
Gain Test Point (V) Upper Limit (V) Lower Limit (V)
1 9.800000 9.80345 9.79655
0.000000 0.001002 -0.001002
–9.800000 –9.79655 –9.80345
100 0.098000 0.098060 0.097940
0.000000 0.000030 –0.000030
–0.098000 –0.097940 –0.098060
Table 7. SCXI-1102 C Test Limits
Gain Test Point (V) Upper Limit (V) Lower Limit (V)
19.800000 9.80345 9.79655
0.000000 0.001002 -0.001002
–9.800000 –9.79655 –9.80345
100 0.098000 0.098060 0.097940
0.000000 0.000030 –0.000030
–0.098000 –0.097940 –0.098060

SCXI-1102/B/C Calibration Procedure 16 ni.com
Table 8. Front Signal Pin Assignments
Front Connector Diagram Pin Number Column A Column B Column C
NC—No Connection
32 CH GND AI 0– AI 0+
31 NC AI 1– AI 1+
30 NC AI 2– AI 2+
29 NC AI 3– AI 3+
28 NC AI 4– AI 4+
27 NC AI 5– AI 5+
26 NC AI 6– AI 6+
25 NC AI 7– AI 7+
24 CH GND AI 8– AI 8+
23 NC AI 9– AI 9+
22 NC AI 10– AI 10+
21 NC AI 11– AI 11+
20 NC AI 12– AI 12+
19 NC AI 13– AI 13+
18 NC AI 14– AI 14+
17 NC AI 15– AI 15+
16 CH GND AI 16– AI 16+
15 NC AI 17– AI 17+
14 NC AI 18– AI 18+
13 NC AI 19– AI 19+
12 NC AI 20– AI 20+
11 NC AI 21– AI 21+
10 NC AI 22– AI 22+
9NC AI 23– AI 23+
8NC AI 24– AI 24+
7NC AI 25– AI 25+
6NC AI 26– AI 26+
5CH GND AI 27– AI 27+
4CJ SENSOR AI 28– AI 28+
3CJ SENSOR AI 29– AI 29+
2CH GND AI 30– AI 30+
1+5 V AI 31– AI 31+
Column
A B C
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1

©National Instruments 17 SCXI-1102/B/C Calibration Procedure
Table 9. Rear Signal Pin Assignments
Rear Connector
Diagram Signal Name Pin Number Pin Number Signal Name
NC—No
Connection
RSVD—Reserved
AI GND 1 2 AI GND
CH 0+ 3 4 CH 0–
NC 5 6 NC
NC 7 8 NC
NC 910 NC
NC 11 12 NC
NC 13 14 NC
NC 15 16 NC
NC 17 18 NC
OUT REF 19 20 NC
NC 21 22 NC
NC 23 24 D GND
SER DAT IN 25 26 SER DAT OUT
DAQ D*/A 27 28 NC
SLOT 0 SEL* 29 30 NC
D GND 31 32 NC
NC 33 34 NC
NC 35 36 AI HOLD COMP, AI HOLD
SER CLK 37 38 NC
NC 39 40 NC
NC 41 42 NC
RSVD 43 44 NC
NC 45 46 RSVD
NC 47 48 NC
NC 49 50 NC
49 50
47 48
45 46
43 44
41 42
39 40
37 38
35 36
33 34
31 32
29 30
27 28
25 26
23 24
21 22
19 20
17 18
15 16
13 14
11 12
910
78
56
34
12

Refer to the NI Trademarks and Logo Guidelines at ni.com/trademarks for more information on National Instruments trademarks. Other product and company names
mentioned herein are trademarks or trade names of their respective companies. For patents covering National Instruments products/technology, refer to the appropriate
location: Help»Patents in your software, the patents.txt file on your media, or the National Instruments Patents Notice at ni.com/patents. You can find
information about end-user license agreements (EULAs) and third-party legal notices in the readme file for your NI product. Refer to the Export Compliance Information at
ni.com/legal/export-compliance for the National Instruments global trade compliance policy and how to obtain relevant HTS codes, ECCNs, and other
import/export data. NI MAKES NO EXPRESS OR IMPLIED WARRANTIES AS TO THE ACCURACY OF THE INFORMATION CONTAINED HEREIN AND SHALL NOT BE LIABLE
FOR ANY ERRORS. U.S. Government Customers: The data contained in this manual was developed at private expense and is subject to the applicable limited rights and
restricted data rights as set forth in FAR 52.227-14, DFAR 252.227-7014, and DFAR 252.227-7015.
© 2000–2015 National Instruments. All rights reserved. 370029C-01 Mar15
World Wide Support and Services
The National Instruments website is your complete resource for technical
support. At ni.com/support you have access to everything from
troubleshooting and application development self-help resources to email
and phone assistance from NI Application Engineers.
Visit ni.com/services for NI Factory Installation Services, repairs,
extended warranty, and other services.
Visit ni.com/register to register your National Instruments product.
Product registration facilitates technical support and ensures that you
receive important information updates from NI.
National Instruments corporate headquarters is located at 11500 North
Mopac Expressway, Austin, Texas, 78759-3504. National Instruments also
has offices located around the world. For telephone support in the United
States, create your service request at ni.com/support or dial
1 866 ASK MYNI (275 6964). For telephone support outside the United
States, visit the Worldwide Offices section of ni.com/niglobal to access
the branch office websites, which provide up-to-date contact information,
support phone numbers, email addresses, and current events.