Navig8r NAVSPORT720 User manual

NAVSPORT720 USER GUIDE

IMPORTANT SAFETY INSTRUCTIONS AND PRECAUTIONS
Read all instructions carefully before use
Retain this product manual for future reference.
Use this product only in the manner described.
Only use awater-dampened soft-cloth to clean the surface ofthe camera
including the lens. Remove particulate such as dirt or grease before you do so
otherwise you may risk scratching the case. The camera is notwaterproof when
it is outside its waterproof case
Be aware of environmental conditions such extreme heat and cold, humidity,
dusty, salty or sandy environments. In extremely cold weather and after
prolonged usage, condensation may form inside the case which maycause the
lens to fog up.We would recommend to stop using the camera and letthe
condensation evaporate (i.e.: don’t try to wipe it off)
For first time use, it is recommended to charge overnight to ensure a full
battery charge. Subsequentcharges can be as required.Duringcharging, or
extended use, the productmay become warm.
There are no user serviceable parts in this product.
Un-authorized attempts to dismantle or repair this productwill void your
productwarranty
Do not point the camera directly at the sun as thismay damage the video sensor
Do not wipe the lens surface with your fingers. Instead use an appropriate lens cleaning
cloth or lenscleaning solution.

ACCESSORIES IN THE BOX

PRODUCT CONNECTION AND BUTTONS:
1
M
icro SD Card
S
lot
7
Mode Switch
2
Re
set
8
Lens
3
U
SB
Port
9
LCD
Screen
4
Power
B
utton
10
Working Indicator
Light
5
M
icrophone
11
Charging
IndicatorLight
6
Shutter
B
utton
12
Wrist
S
trap
Hole

Charge the Built-in Lithium Battery
Turn the camera off and connect the USB cable to the camera and to your power source (i.e.PC USB port
orUSB Mains PowerAdaptor) The chargingindicatorlightwill be ON when charging and OFF when fully
charged. A full charge can take up to 4 hours.
Waterproof Case Operation
1. Use your fingertip to gently pull the release clamp (4)back, in the direction of the arrow (on the clamp body)
2. Inspect the rubber waterseal gasket to ensure itisin good condition, and then insertthe camera in the correct
orientation.
Note 1:You can test the gasket by closing the case without thecamera inside and submersing it completely in a
bowl of water fora few minutes. Remove the case from the water, dry off the exterior with a towel, and then
open the case.If the interior is dry, the camera andcase will be safe for use under water.
Note 2: Only two buttons arerequired for recording video and images: the Shutter Button, and the On/Off
button.
Note 3: Rememberto select the desired Mode on the camera before closing the case.
On/Off
Button
Releaseclamp
4.
Case Hinge
Shutter
Button

4
1
-
20 Screw
Handlebar Seat Post Mount
Note 1: Thiscamera does not have a standard tripod mount fastener.
Note 2: Always use thesupplied waterproof case or mounting adapter when connecting to other ¼”- screw fixture
accessories (eg. a Tripod)
1. Connect the handlebar clamp (4) to the ¼” (1) screwand turn clockwise until secure.
2. Turn the locking wheel (2) so it applies pressure back against the case.
3. Loosen onebar clamp bolt(3) until the Barclamp bracket (4) can be rotated 90 degrees.
4. The bracket can then acceptand be attached toany round fixture such as the bicycle handlebars.
5. After positioning thehandlebar clamp,closeup the bottom half ofthe clamp and tighten theclamp nuts (3).
6. Loosen the tilt knob (5) to adjust the frame angle then tighten off the tiltnut.
7. Panning adjustments can be made by loosening the Locking Wheel, adjust the pan angleand re-tightening the
wheel.
MOUNTING ADAPTOR / SHIELD
This Mounting Adapterallows you to attach OTHER mounting
accessories that use a ¼” screw, withoutusing the waterproof
case.
Note:The camera willclip into this adapter.
Locking Wheel
Bar Clamp
Nuts
BarClamp
TiltKnob
“Screw

¼”
Screw
Mount
Helmet Mounting Kit
Note: This bracket will only work with vented Helmets.
Use the supplied strap to loop through the holesin your helmetand then through the longslots onthe
helmetmount. Tighten as required.
MOUNTING EXAMPLES
Locking
Wheel
HelmetBelt
HelmetMount
Tilt
Knob
HANDLE BAR EDITION

Inserting the Micro SD Card
Push the memorycard into thecard slot,as shown in the diagram below.The Micro SD card will“clicks into
place”. To take the memory card out, gently press the end of the memory card inward using your fingernail
until a click is heard. An internal spring willthen release the card.
Note:This camera has no built-in memory. A memory card is needed for operation.
STARTUP/SHUTDOWN
1. START-UP:Press and hold the powerbutton until the welcome screen is displayed.
2. SHUTDOWN: Press and hold the power button until the Goodbye screen is displayed.
Note 1: This camera will automatically shut down after 5 minutes of inactive use to conserve power.
Note 2: Ifthere is not enough power the low powerbattery icon will flash. When power has
been exhausted the camerawill shutdown.

SWITCH BETWEEN FUNCTION MODES
Picture mode: Digital Still Camera operation
(To start recording press the shutter button or tap centre screen)
Video mode: Record video
(To start recording press the shutter button or tap centre screen)
Vehicle-mounted mode: Cycle record video in 5 minute files (Crashcam function)
(To start recording press the shutter button or tap centre screen)
Picture
mode
Video
mode
V
ehicle
mode
Mode
Switch

RECORDING
Except forthree on-screen icon types,all icons are the
same across all three recording functions (Camera,
Video and In-Car) moving clockwise from the top
middle icon or black box:
Note:A crossed out black box indicates
a unique mode feature as explained further.
Note:During extended sessions of playback, the screen
automatically turns off to conserve power. Press the
power button to turn the screen back on if required.
a.
b.
c.
a. Select Resolution in
Still Camera Mode (1/3/5MB)
b. Select Resolution in
Video Mode (HD/VGA)
c. Select Resolution in
In-Car Mode (HD/VGA)
Magnify / Zoom In
Magnification value
Magnify / Zoom Out
Playback
a.
b.
c.
a. Still Camera Mode
b. Video Mode
c. In Car mode
Battery power indicator
SetDateand time
Indication that SD card has
been inserted
a.
b.
c.
a. Still Camera mode
Image number “X” of “Y”
b. Video mode
time remaining
c. In-Car mode
time remaining
Frame Centre –
On screen shutter button

PLAYBACK MODE
The Playback mode is common for allfile types and modes. For example from this one screen, you can
scroll through all yourJPG and AVIfiles recorded in both carand video mode.
Quick Reference Guide:
1 : Displays the current file being played back. In this case itis an AVI video file.
2 : Displays the file number (X) and the total files in a folder (Y). (I.e. X/Y)
3 : Displays the current folder location i.e. I:\DCIM\100MEDIA (I: Drive is and example)
4 : Click to select the next file.
5 : Click to select the previous file.
6 : Click to delete a file
7 : Click to Play / Pause playback video files
8 :Click to return you to the previous mode eg. Video mode
9 : Click to rewind or fast forward.
CONNECTING TO A COMPUTER
Files can be played back directly from the Camera to a Windows ® Computer via a USB cable. The camera
willappearas a common removable disk under Window Explorer.Photos/Videos aresaved in folder
I:\DCIM\100MEDIA.In vehicle recorded files are saved to I:\DCIM\RECORDER.

TECHNICAL SPECIFICATIONS
Image sensor
1.3 millio
n pixel (CMOS)
Function mode
Taking
video
Taking photos
Vehicle-mounted mode
Camera lens
F3.1 f=9.3mm
Z
oom
4
X Digital
Shutter
Electronic
LCD display screen
2.0
-
inch
T
ouch
S
creen
Image resolution 1M(1280×1024), 3M (2048×1536), 5M
(2592×1944)
Video resolution VGA: 640x480 (60 frames/second)
720P:1280x720 (30 frames/second)
White balance
Automatic
Exposure
Automatic
File formats
Image
JPEG
Video
AVI
Storage medium
M
icro SD
card (
U
p to 32GB)
. There is no built in
memory.
USB interface
High
-
speed USB 2.0 interface
PowerSupply
Built
-
in 3.7V rechargeable lithium
Dimension (length × width ×height)
66
X
45
X
2
5
mm
Weight
4
8
grams

Warranty against Defects
Laser Corporation Pty Ltd (“Laser”) warrants your new product to be free from defects in materials and workmanship for 12
months, from the date of purchase, provided that the product is used in accordance with accompanying recommendations or
instructions where provided. The benefit of this warranty is in addition to your rights under the Australian Consumer Law and
to other rights and remediesof theconsumer undera law in relationto the goodsor services to which thewarrantyrelates.
Through a network of retailers and resellers, Laser will provide you with your choice of a refund, repair or exchange (where
possible) for this product if it becomes defective within the warranty period. This warranty will no longer apply where the
defect isa result of alteration, accident, misuse,abuse, normalwear and tear, neglect or improper storage.
Pleaseretainyourreceiptasproofof purchase.
How to makea product warrantyclaim:
Step 1: Find your receipt which proves the date of purchase. Where the date of purchase cannot be verified, your place of
purchase or Laser will make an assessment based on the date of manufacture, the condition of the Laser product and the type
of defect.
Step 2a): Contact your place of purchase. They will assess the nature of the fault and refund or replace the product as per
their storerefundorwarrantypolicy.
Step 2b): If your place of purchase cannot be contacted, then you can contact Laser Customer Service with details of your
defective Laser Product Phone [phone]; or Email: [e-mail] or online www.laserco.net/support/warranty
(click on “Consumers(End Users)”). Our business address is at 1/6-8 Byfield Street, NorthRyde, NSW2113
Step 3: Laser will issue you with aReturn Authorisation (RA) number within 48 hours. When requested, send us the defective
productand acopy of your receipt.Laserwillcover thecost of the return delivery.
Step 4: Wait for us to contact you. Once we have received your defective Laser product for inspection, we will inform you of
our assessment of your claim within 7 days. When we contact you, we will firstly let you know whether you have a valid claim
under this Warranty, and if so, we will inform you whether your defective Laser product will be replaced or repaired, together
with the number of days you can expect to wait to receive your replaced or repairedLaser product.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a
replacementor refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced ifthe goods fail to beof acceptable quality and the failure doesnot amount to a
major failure.