nbf SIGNATURE SERIES 61019 User manual

COMPONENTS
INSTRUCTIONS
AB
HARDWARE & TOOLS
Mounting Plate - 1pc Keyboard Desktop - 1pc CMiddle Bracket - 1pc
DEF
ASSEMBLY INSTRUCTIONS
Congratulations on the purchase of your new Signature Series product!
Monitor Mount Kit - 4pcs
H
Screws M6*12- 4pcs Allen Key(4mm) - 1pc
STEP 1
Electric A
Screws M5*10- 4pcs G
Allen Key(333 mm) - 1pc
3
Shown upside-down
Cable clamp - 4pcs
I
B
C
E
Attach the Middle Bracket (C) to the Keyboard Desktop
(B) using four M5×10 mm screws (E) using the 3 mm
Allen Key (F).
NBF-ESW004M-BK/WH
dj u stable H eig ht Sing le Monitor R iser with Memory
JSpanner (1 mm) - 1pc
3
of each item
F

INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
Congratulations on the purchase of your new Signature Series product!
STEP 2
STEP 3
D
G
A
Attach the Mounting Plate (A) to the column using four
M6×12 mm screws (D) with the 4 mm Allen Key (G).
Raise the unit to its highest level by pressing the UP (+)
arrow unti it reaches its highest eve and stops.
NBF-ESW004M-BK/WH
Electric A dj u stable H eig ht Sing le Monitor R iser with Memory

INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
Congratulations on the purchase of your new Signature Series product!
STEP 4
STEP 5
< 50 KGS
(< 110 LBS)
< 5 KGS
(< 11 LBS)
< 10 KGS
(< 22 LBS)
Unlock the Keyboard Platform Clamps underneath the desktop by pulling Clamps downward into the unlocked
desktop.
locked position.
NBF-ESW004M-BK/WH
To Lock
COMPLETED RISER ASSEMBLY
Electric A dj u stable H eig ht Sing le Monitor R iser with Memory
position. Insert the Keyboard Platform into the channels in the bottom of desktop until it is flush with edge of
Lock the Keyboard Platform in place by pushing Platform Clamps upwards towards the post into the

INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
Congratulations on the purchase of your new Signature Series product!
STEP 6
H
Attach monitor to mounting plate using hardware in Monitor Mount Kit (H).
Electric A dj u stable H eig ht Sing le Monitor R iser with Memory
Monitor Mount Kit - 1 bag
with 4pcs of each item per bag
NBF-ESW004M-BK/WH
Use 13mm Spanner (J) for tightening Mounting Plate(A). If Mounting
Plate(A) is loose, remove center plastic cover and tighten screw
with 13mm Spanner (J).
J

INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
Congratulations on the purchase of your new Signature Series product!
1. Handset Display Symbols :
LED Height Display Screen (features Energy saving Standby/Sleep function)
Key + : Up motion
Key - :Down motion
Key 1 First memory setting
Key 2 Second memory setting
Key 3 Third memory setting
Key M Key to set Memory
1. Long press(5 seconds) the M key, LED screen show " 1-0 " and " 0 " flashing.
2. Press the UP (+) key or DO W N ( - ) key to adj ust flashing " 0 ".
3. Flashing " 0 " means Centimeter
Memory Setting Instructions
NBF-ESW004M-BK/WH
2. How to change Centimeter to Inches :
Flashing " 1 " means I nches
4. Long press (5 seconds) the M key to program the setting.
Eg.
M
1-0
UP +
or
DOWN - 1-1
:
:
:
:
Electric A dj u stable H eig ht Sing le Monitor R iser with Memory
M
HO LD PRESS Display shows for
centimeter Display shows for
inches HO LD to program

INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
Congratulations on the purchase of your new Signature Series product!
Program height selections to Memory
Find desired height. Press Key M once. LED screen will show display " 5 - " .
Eg.
M
5 -
NBF-ESW004M-BK/WH
Q uickly press desired key number twice.
Press once Display shows
4. T roub lesh ooting :
Fault code Faulty description Solution
E-1 Motor hall break or Signal problem Call supplier
E-2 Motor's phase wire disconnect Call supplier
E-3 Motor unplug Call supplier
E-4 Motor short circuit Call supplier
E-5 Motor stalling Call supplier
E-6 Motor hall direction doesn't match phase wire Change two hall wires
E-7 Control box problem Call supplier
E-8 Handset disconnect well Call supplier
E-10 Screw rod to botton or to topside Reset
E-12 Electricity power down during working Connect power plug well
E-13 Anti-collision function working
3.
Electric A dj u stable H eig ht Sing le Monitor R iser with Memory
Press Twice
1,2 or 3