NCR 7707-K261 Manual

Kit Instructions
Handheld Scanner Holster
7707-K261
Issue A

The product described in this document is a licensed product of NCR Corporation.
NCR is a registered trademark of NCR Corporation. NCRSelfServ™ Checkout is a trademark of NCR Corporation in the United
States and/or other countries. Other product names mentioned in this publication may be trademarks or registered trademarks of
their respective companies and are hereby acknowledged.
Where creation of derivative works, modifications or copies of this NCR copyrighted documentation is permitted under the
terms and conditions of an agreement you have with NCR, NCR's copyright notice must be included.
It is the policy of NCR Corporation (NCR) to improve products as new technology, components, software, and firmware become
available. NCR, therefore, reserves the right to change specifications without prior notice.
All features, functions, and operations described herein may not be marketed by NCR in all parts of the world. In some instances,
photographs are of equipment prototypes. Therefore, before using this document, consult with your NCR representative or NCR
office for information that is applicable and current.
Copyright © 2022
By NCR Corporation
864 Spring St. NW
Atlanta, GA 30308
United States
All Rights Reserved

iii
Revision Record
Issue Date Remarks
AApr 2022 First Issue

iv

Handheld Scanner Holster
The Handheld Scanner Holster holds the Handheld Scanner. It is attached to a bracket,
which can be installed on either side of the Terminal Display depending on the
orientation of the NCRSelfServ™ Checkout (7707) unit. This publication provides
procedures for installing a Handheld Scanner Holster on an NCRSelfServ™ Checkout
(7707) unit.
Kit Contents
Part Number Description
497-0532993 7707-K261 Handheld Scanner Holster Kit
006-8611658 Screw,M3 x 5, SEMS, PHIL, PAN, STL, Z (2 pcs)
006-8624472 Acorn Nut – M4 x 0.7 mm, 7 mm Width, 8 mm Height -
Black Oxide Finish (2 pcs)
006-8628477 End Cap - Handheld Holster (2 pcs)
497-0520400 Bracket - Handheld, Display Mount
497-0531681 Holster, Scanner, Handheld
*497-0423108 Instructions Kit (Reference Sheet)
* Items marked with an asterisk are not called out on the image.

2 Handheld Scanner Holster
Installation Procedures
To install the Handheld Scanner Bracket, follow these steps:
1. Remove the Terminal Display. For more information, refer to Removing the Terminal
Display on page5.
2. Remove the Terminal Display Rear Cover. For more information, refer to Removing
the Terminal Display Rear Cover on page7.
3. Do any of the following, if necessary:
• Remove the Wireless Antenna Module. For more information, refer to Removing
the Wireless Antenna Module on page8.
Note: Both Semi-Self and Self-Checkout configurations of NCRSelfServ™
Checkout (7707) allows the 7702 Terminal Display to hold both the Wireless Card
Antenna and the Handheld Scanner Bracket. Depending on the orientation of the
unit, the two devices can be interchanged.
• Remove the existing scanner bracket assembly by removing the two(2) screws
securing the scanner bracket to the Display Collar, as shown in the image below.

Handheld Scanner Holster 3
• For No-Handheld Scanner units, remove the Blanking Plate using a pry tool.
Note: Remove all adhesive residues from the Blanking Plate.
4. Install the Handheld Scanner Bracket by doing the following:
a. Install the Holster to the bracket using two acorn nuts.

4 Handheld Scanner Holster
b. Attach the scanner bracket assembly to the Display Collar using two (2) screws,
as shown in the image below.
Note: The scanner bracket assembly can be installed on either side of the
Terminal Display. For the purpose of illustration only, the image below shows a
Right-hand (RH) orientation.
5. Install the Wireless Antenna Module on the other side of the Terminal Display, if
necessary. For more information, refer to Installing the Wireless Antenna Module on
page12.
6. Install the Terminal Display Rear Cover. For more information, refer to Installing the
Terminal Display Rear Cover on page15.
7. Install the Terminal Display. For more information, refer to Installing the NCR
Terminal Display on page16.

Handheld Scanner Holster 5
Removing the Terminal Display
To remove the NCR Terminal Display, follow these steps:
Note: For the purpose of illustration only, this procedure shows images using a 7702
Terminal Display.
1. Shut down the NCR Terminal Display software and hardware systems.
2. Unlock the Tower frame from the back panels using a key.
3. Raise the Terminal Display.

6 Handheld Scanner Holster
4. Open the cable cover by pushing both ends as shown below.
5. Disconnect the cables from the terminal.
6. Remove six (6) screws to detach the Terminal Display from the Display Hinged
Bracket, as shown in the image below.
7. Do the following:
a. Slide the Terminal Display to the back to disengage it from Upper Enclosure
b. Lift the Terminal Display away from the unit and place it on a flat surface with
the back facing up.

Handheld Scanner Holster 7
Removing the Terminal Display Rear Cover
To remove the Rear Cover of the Terminal Display, follow these steps:
1. Remove the cable cover.
Note: Place the Terminal Display on a flat surface with the back facing up.
2. Remove the two (2) screws to detach the rear cover from the Terminal Display, as
shown in the image below.
3. Detach the rear cover.

8 Handheld Scanner Holster
Removing the Wireless Antenna Module
To remove the Wireless Antenna Module, follow these steps:
Note: For more information about the wireless card and antenna, refer to the RealPOS
XR7 (7702) POS User Documentation.
1. Remove the Terminal Display Rear Cover, if necessary. For more information, refer
to Removing the Terminal Display Rear Cover on the previous page.
2. Disconnect the Ground and Wireless Antenna cables from the board, as shown in the
image below.
3. Remove nine (9) screws to detach the Display Collar from Terminal Display, as
shown in the image below.

Handheld Scanner Holster 9
4. At the back of the Display Collar, unhook the cable from the hook feature on the
Display Collar, as shown in the image below.
5. Remove two (2) screws to detach the Wireless Antenna Module from the Display
Collar, as shown in the image below.

10 Handheld Scanner Holster
Removing the Handheld Scanner Bracket
To remove the handheld scanner bracket, follow these steps:
Note: The images in this procedure use the default orientation of the bracket.
1. Do the following:
a. Remove the handheld scanner from the bracket.
b. Remove the Terminal Display. For more information, refer to Removing the
Terminal Display on page5.
2. Place the Terminal Display on a flat surface with the back facing up.
3. Disassemble the rear cover by doing the following:
a. Remove the cable cover.
b. Remove the two (2) screws to detach the rear cover from the Terminal Display,
as shown in the image below.

Handheld Scanner Holster 11
c. Remove the nine (9) screws to detach the Display Collar from the Terminal
Display, as shown in the image below.
4. Remove two(2) screws to detach the scanner bracket from the Display Collar, as
shown in the image below.

12 Handheld Scanner Holster
Installing the Wireless Antenna Module
To install the Wireless Antenna Module, follow these steps:
Note: For more information about the wireless card and antenna, refer to the RealPOS
XR7 (7702) POS User Documentation.
1. Secure the Wireless Antenna Module to the Display Collar using two (2) screws, as
shown in the image below.

Handheld Scanner Holster 13
2. Route the cables through the cable management feature on the Display Collar, as
shown in the image below.
3. Secure the Display Collar on the Terminal Display using nine (9) screws, as shown
in the image below.

14 Handheld Scanner Holster
4. Connect the Ground and Wireless Antenna cables to the board, as shown in the
image below.
5. Install the Terminal Display Rear Cover, if necessary. For more information, refer to
Installing the Terminal Display Rear Cover on the facing page.

Handheld Scanner Holster 15
Installing the Terminal Display Rear Cover
To install the Rear Cover of the Terminal Display, follow these steps:
1. Attach and secure the rear cover on the back of the Terminal Display using two (2)
screws, as shown in the image below.
2. Install the cable cover.

16 Handheld Scanner Holster
Installing the NCR Terminal Display
To install the NCR Terminal Display, follow these steps:
Note: For the purpose of illustration only, this procedure shows images using a 7702
Terminal Display.
1. Remove the existing NCR Terminal Display, if necessary. For more information,
refer to Removing the Terminal Display on page5.
2. Install the Adaptor Plate to the Display.
3. Mount the Terminal Display on the Upper Enclosure and then secure using four (4)
M4 x 8 machine screws, as shown in the images below.
4. Connect cables to the Terminal Display.