Necker V1 User manual

1
Table of Contents
1. Introduction………..…………………..……….... 2
zSystem Requirements……………………… 3
2. Preparation……………..………………………. 4
zComponent & Accessories…………..…….. 4
zPart Names………………………………….. 5
zIndicator LED………………………………… 6
3. Charging…………………………………………. 7
4. Recording….……………………………………. 9
zCar Mode……………..….…………………... 9
zSport Mode………………………………….. 12
5. Download………………………………………… 15
zDownload from NECKER V1………….….. 15
zDownload from Card Reader……………… 16
6. Playback…………………………………………. 17
zPlayback from PC / Mac..………………….. 17
7. Wireless…...……………………………………... 18
zEnable Wireless Function………………….. 18
zEnable APP Function……………………….. 20
8. Expert Mode……………………………………... 21
zLoad from NECKER V1…………….…….. 21
zLoad from microSD Card Reader…………. 22
zAdjust NECKER V1 Settings………………
zAdjust the Date and Time Settings………..
23
24
9.
10.
FAQ………………………………………........
Appendix……………………………………….
●Specification………………………………
●Default Setting………………………………
25
28
29
EN

2
1. Introduction
Welcome to the world of digital imaging. The following information will help you to use your
NECKER V1 to its full capabilities.
Before you install and operate the product, please take a few minutes to read through this
manual. It provides proper instructions for you to install and operate the product.
The NECKER V1 may be affected by static electricity interference. Please plug-in / out and
wait a few minutes to start this function.

3
zSystem Requirements
PC System Requirements
zIntel® Core2Duo 1.8G or AMD equivalent CPU
zHi-speed USB2.0 port
z1 GB RAM internal memory minimum
z500MB free hard disk space
z800 x 600 pixel color monitor
znVIDIA GeForce MX440 or above, AMD (ATi) Radeon 9200 or above
zDirectX 9.0 or higher
zWindows® XP (SP2 or higher) / Windows Vista™ / Windows 7™, Windows 8™
Note: If your system is Windows XP Service Pack I, please go to www.microsoft.com. It’s
free to update your system to Windows XP Service Pack II.
Mac System Requirements
zPower PC G5 or Intel Core Duo processor recommended
zFree USB2.0 port
z1 GB RAM internal memory minimum
z500MB free hard disk space
z800 x 600 color monitor
zMac OS 10.5 or above
EN

4
2. Preparation
zComponent & Accessories
NECKER V1 Sport DV QOG User Manual
USB Cable AC Adaptor Camera Holder
Hand Strap Waterproof MicroSD Hi-Speed
Car Charger (optional) charger cable
(Forcharging
useonly.)
Base Mount Tripod Mount Bike Mount Universal
Mount

5
zPart Names
EN

6
zIndicator LED
Front LED Rear LED
Off Off -Power
On Blue, On -
Off Off -Record
On Blue, Slow Blink -
Off - Off
Booting - Red, Slow Blink
Wireless
On - Red, On
Low Blue, Quick Blink -
Charge - Green, On
Battery
Full - Off
No Card - Red, Quick BlinkSD Card
Card Full - Red, Quick Blink

7
3. Charging
1. Remove the rear protective cap of the NECKER V1 and connect the supplied mini USB
cable into the NECKER V1.
2. Plug the USB cable into the supplied AC wall adaptor, car adaptor, or a PC / Mac USB
port.
EN

8
3. The NECKER V1 will illuminate the Green LED in the Rear LED to tell you it’s charging.
4. When the Green LED turns off, the battery is full and charging is complete.
Note: The Front LED will blink blue and auto power off after 10 seconds when the battery
power is low and reference the charging procedure to recharge it.

9
4. Recording
zCar Mode
1. Remove the rear protective cap of The NECKER V1 and insert a microSD card (optional)
in the microSD Card Slot.
2. Slide the Mode Switch to the Left side.
Note: 1. In Car Mode, the NECKER V1 circulate record video and overwrite the oldest
recorded file first.
2. The record file automatic divides each 1, 3 or 5 minutes depend on user
setting.
3. Hold down the Power Button for 1 seconds and release, the NECKER V1 will illuminate
the Blue Front LED and vibrates 3 times. The Rear LED will blink Red and boot the
wireless module.
EN