Nembrini Audio LEAD Series User manual

MRH810 V2 LEAD SERIES MANUAL

MRH810 V2 LEAD SERIES GUITAR AMPLIFIER
Congratulations on choosing our new MRH 810 V2 Lead Series Guitar Amplier!
This plugin faithfully reproduces the behavior and character of a famous 80s British high gain guitar amplier that
dened an era. We spend years of experience on modeling to build a Guitar Amplier plugin that is at the meantime
easy to use and good sounding in any situation and settings.
No wired controls and difcult names, but only the classics controls of a real guitar amplier!
But we have extended the possibility of the original hardware thanks to the versatility of the digital world with new
features for the maximum control of your tone!
Thanks to the versatility of the digital world, we have extended the possibility of the original hardware with new
features for the maximum control of your tone:
- 6 carefully selected cabinet emulations
- 4 of the best mic emulations used in real recording sessions
- selectable mic positions with volume and pan controls
- noise gate and clean circuit
- a powerful impulses loader to load your favorite IRs

MRH810 V2 LEAD SERIES GUITAR AMPLIFIER
Front Panel
The front panel contains the main control of the MRH 810 V2 Guitar Amplier plugin
1 - Power On/Off Switch: bypass the plugin to compare your processed and unprocessed signal.
2 - Master section: contains the controls of the power amp section of the MRH 810 V2 Guitar Amplier
Presence - adjust high frequency content to your tone
Volume - this controls the master volume of the amplier
Reverb - adjust the amount of reverb to your signal
3 - Lead Channel: this section contains the controls of the lead or distorted channel of the MRH 810 Guitar Amplier
Led status - when on it indicates that the lead channel is active
Bass/Middle/Treble - tone stack controls for the lead channel
Volume - adjust the volume of the Lead Channel of the preamp section before the master section
Gain - adjust the amount of of distortion of the preamp section
1 2 3 4 5

MRH810 V2 LEAD SERIES GUITAR AMPLIFIER
4 - Channel Selector: this control switches between Lead Channel and Clean Channel
5 - Clean Channel: this section contains the controls of the Clean Channel of the MRH 810 V2 Guitar Amplier
Led status - when on it indicates that the lead channel is active
Bass/Treble - this 2 knobs controls the tone of the Clean Channel
Volume - adjust the volume of the Clean Channel of the preamp section before the master section
1 - Cabinet - Impulse Loader button: opens and closes the Cabinet - Impulse Loader panel
1

MRH810 V2 LEAD SERIES GUITAR AMPLIFIER
Cabinet - Impulse Loader panel
12
3
4
5
1 - Recording Chain Mode: this three buttons switches between the included cabinet/recording
chain emulation, the Impulse Loader and the complete bypass of the entire cabinet/recording chain
emulation. The Cleaner (2), Noise Gate (3) and Levels (4) sections are always active in all the three
Cabinet Mode.

MRH810 V2 LEAD SERIES GUITAR AMPLIFIER
2 - Cleaner: this lter section has ben added to our MRH 810 V2 Guitar Amplier for clear your tone
Rumbling: reduces the low frequency content
Harsh: reduces the high frequency content
3 - Noise Gate: allows you to eliminate the noise produced by the large amount of gain
Power: activates the Noise Gate circuit
Threshold: denes the level where the gate is activated
Range: selects the quantity of noise reduction
4 - Levels: this section let you to control the level before the plugin process and after all the processing
Input : adjust the input level from minus innite to 12db
Output : adjust the output level from minus innite to 12db
5 - Fix button: pressing this button your input level remains the same when you change presets.

MRH810 V2 LEAD SERIES GUITAR AMPLIFIER
Cabinet MODE
1 - Cabinet: you can choose between six selected cabinet emulation
1- MRH 4x12 T75: based on Marshall* 1960B 4×12 with Celestion G12T-75W speakers
2- MRH 4x12 G12 : based on Marshall* 1960B 4×12 with Celestion G12T-25W speakers
3- MB RECT 4x12 V30: based on Mesa Rectier* 4x12 with Celestion Vintage 30 speakers
4- ORANGE 4x12 V30: based on Orange* 4×12 with Celestion Vintage 30 speakers
5- BG 2x12 V30: based on Bogner* 2x12 Celestion Vintage 30 speakers
6-TWEED 4x10 P10Q: based on Fender* Tweed Bassman 4x10 Jensen P10Q speakers
1 2 3

MRH810 V2 LEAD SERIES GUITAR AMPLIFIER
2 - Mic 1 and Mic 2 settings: You can use 2 virtual microphones for your amp recording chain and select between 4
different models, select between On or Off Axis postions, change the Position and Distance.
The emulated microphone are:
1 - Dynamic 57: based on popular Shure* SM-57 dynamic microphone
2 - Ribbon 121: based on modern Royer* Labs R-121 ribbon microphone
3 - Condenser 414: based on classic AKG* C 414 condenser microphone
4 - Dynamic 421: based on vintage Sennheiser* MD-421 dynamic microphone
3 - Mixer: This 3 faders controls the volume of the 2 microphones in front of the guitar cabinet and the stereo
ambience microphones.
Each channel have a pan control for stereo positions, solo, mute and phase inversion switch.
* Please note that all marks and models are all trademarks of their respective owners, which are in no way associated or afliated with
Nembrini Audio. These marks and names are used solely for the purpose of describing certain tones produced using Nembrini Audio’s modeling
technology.

MRH810 V2 LEAD SERIES GUITAR AMPLIFIER
IMPULSES MODE
The Nembrini Audio Impulses Loader let you load up to three 3rd-parties impulse responses and blend
them together. The following settings are available for each of the three loaded IRs:
1 - Empty button: unload the current IR
2 - Browse button: open an explorer window that permit you to select a folder and show you the contained wav les
in the adjacent display (5).
3 - Load button: open an explorer window that permit you to load your favorite impulse response.
1
2
3
4
5

MRH810 V2 LEAD SERIES GUITAR AMPLIFIER
In this mode the whole cabinet / recording chain section and impulses loader are completely bypassed,
letting you use your favorite impulse loader or your real power amplier and speakers system with
the MRH 810 V2 Guitar Amplier
BYPASS MODE
4 - IR controls: you can change the volume, pan, phase of each IR and Solo or Mute it
5 - Browse/Preview display: in this display you can browse your favorite IRs or view a preview
of the resulting waveform

MRH810 V2 LEAD SERIES GUITAR AMPLIFIER
The Toolbars
1 2 3 4 5 4
Top Toolbar
1 - Open the manual and the information about the plugin.
2 - + and - buttons allow you to scroll through the presets.
3 - Undo/Redo changes made to the parameters of the plugin at any time.
4 - With A/B banks, it is possible to compare two different settings in an easy way. It is also possible to compare pre
sets by loading them in the two different A/B banks.The red highlight will show the currently selected bank and what
you will modify/save.
5 - Copy the settings from a bank to another, so you can make slight changes to the controls and compare the two
settings for example.

MRH810 V2 LEAD SERIES GUITAR AMPLIFIER
2 3 4 5
1 - Shows you the active preset. Click on the label to see the preset list.
2 - Allow you to override the current selected preset.
3 - Save the current selected preset as a new preset with a name of your choice.
4 - Delete the selected preset.
5 - Bypass the plugin in order to compare your processed and unprocessed signal.
1