Neo-Neon FCB-VI-OX0125L-6FT-12P User manual

The Instruction Manual for 6' RGB Cone Tree
Model No.: FCB-VI-OX0125L-6FT-12P
Input Voltage: 120V~60Hz 1.5A Max.
Output: 12V 6.0A
CAUTION:
Use only UL Listed Class2 12V DC Power Supply.
This seasonal product is not intended for permanent installaon.
To reduce the risk of fire or electric shock, do not aempt to replace lamps or modify string.
Always unplug this product before installing.
To reduce the risk of fire and electric shock: Do not install on trees having needles, leaves or branch
coverings of metal ormaterials which look like metal.
To reduce the risk of fire and electrical shock: Do not mount or support strings in a manner that can cut or
damage wireinsulaon.
IMPORTANT SAFETY INSTRUCTIONS
When using electrical products, basic precauons should always be pracced including the following:
1.Please read this manual before use;
2.When the temperature is below ≤ 50°F (10°C), please do not directly straighten the lamp body because the
lamp body is hard,so as not to damage the lamp body. It is recommended to connect the power supply to
light the lamp body for 8~10 minutes.When the lamp body is so, Can be straightened and assembled.
3.In order to reduce the deformaon of the lamp body, it is recommended to vercally pull down the straight
lamp bodyduring assembly. Do not forcibly straighten the lamp body when the lamp body is twisted.
4.The lamp beads are not replaceable;
5.The external wires of the product cannot be replaced. If the external wires are damaged, do not use them.
6.Do not connect with other products;
7.Products can be used indoors and outdoors;
8.Do not place the product near gas, electric heaters, fireplaces, candlescks, or other similar sources of heat;
9.The products are electronic products, non-toy products, please do not play for children, please keep them
out of reach ofchildren, so as not to cause fire, burns, personal injury, electric shock and so on;
10. Avoid piercing the lamp body with sharp objects;
11.Aer the product is installed, do not hang other objects on the product;
12.Do not cover flammable materials when using the product;
13.Please check the integrity of the product before use or before using it. If the product is damaged, please do
not use it. If it isdamaged, please do not use it.
14.The product must be connected to the correct voltage;
15.When a fault occurs, please turn off the power immediately. Hold the plug when the power is off, and do
not pull the powercord;
16.If the operaon is not carried out in accordance with the precauons, the manufacturer will not be
responsible.
Page 1 / 3

Page 2 / 3
# Name Qty.
1
Waterproof power supply 1 pc
2
Controller 1 pc
3
Male and female connectors 1 couple
4
Screws for Base 2 pcs
5
Base frame 1 pc
6
Base outer ring 2 pcs
7
Hook 4pcs
8
Pin 12 pcs
9
Linear Light 12 pcs
10
Star 1 pc
11
Center Supporng Tube 2 pcs
Remote Control User Manual
1. Pull out the plasc film from the baer cover to energize the remote. (Fig.1)
2. Point remote to the tree controller box to funcon.
Baery Cauon:
1. Always purchase the correct size and grade of baery most suitable for the intended use.
2. Replace only with lithium, type CR2032 baery
3. Clean the baery contacts and also those of the device prior to baery installaon.
4. Ensure the baery is installed correctly with regards to polarity (+ and -)
5. Remove baery from equipment which is not to be used for an extended period of me.
12
Remote Controller 1 pcs
1
2
3
45
7
8
9
6
10
11

Page 3 / 3
Product Installaon:
Step 1: Open the base frame, and insert guide post of the base frame into the hole on the
outer ring, and fix the base with screws; (Figure 1 and Figure 2)
Step 2: Insert the 3-secons center supporng tube into the hole at base frame; (Figure 3)
Step 3: Insert the Star into the iron frame hole at the top of the lamp body; (Figure 3)
Step 4: Insert the iron frame of lamp body into the center supporng tube; (Fig. 3)
Step 5: Open the reeled lamp body and pull down the lamp body to be straight, and insert the
pin into the T-joint hole and the outer ring hole of the base; (Figure 4)
Step 6: If the product is placed outdoors, please hook one end of the hook to the outer ring of
the base and one end to the ground; (Figure 5)
Step 7: Connect the connector of the lamp body to the connector on the controller; (Figure 5)
Step 8: Power on.
Figure 1 Figure 2 Figure 3 Figure 4 Figure 5
Maintain and Care
You should maintain and care for the tree light kit in the following areas before storage.
1. Clean and wipe all the metal parts. Use rust removal product (not included) such as WD-40 to clean
any rusty spots if there is any when powder coang is damaged. (Note: Follow the rust removal
product instrucons when using it.)
2. Repaint any spots where the paint on the metal part is damaged. (Note: Paint not included)
3. Clean and wipe the light strands and all other parts. (Important: DO NOT let any part of this product
submerge or soak in water.)
4. Be sure all parts are dry before storage.
1
2
3
45
7
8
9
6
10
11

NOTE: This equipment has been tested and found to comply with the limits for a Class B
digital, pursuant to Part 15 or the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may casue harmful interference to radio
communications, However, there is no guarantee that interference will not occur in a particular
installation. If the equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
--- Reorient or relocate the receiving antenna.
--- Increase the separation between the equipment and receiver.
--- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
--- Consult the dealer or an experienced radio/ TV technician for help.
Any Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.