NETGEAR DGN1000v3 User manual

NETGEAR, Inc.
350 East Plumeria Drive
San Jose, CA 95134 USA
June 2013
Trademarks
NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks
and/or registered trademarks of NETGEAR, Inc. and/or its subsidiaries in the
United States and/or other countries. Information is subject to change without
notice. © NETGEAR, Inc. All rights reserved.
Compliance
For the current EU Declaration of Conformity, visit
http://support.netgear.com/app/answers/detail/a_id/11621/.
N150 Wireless ADSL2+ Modem Router
DGN1000v3 Installation Guide
Package Contents
The box contains the following items. If any items are incorrect,
missing, or damaged, contact your NETGEAR dealer.
Note: Your package might contain more items. The filter,
phone cable, or splitter provided depends on the region, and
in some locations, a CD is included.
Note: If your subscriber line
supports ADSL2+ Annex J,
your package also includes a
German plug-to-WAN jack adapter.
N150 Modem Router
Ethernet cablePhone cable
Power adapter Filter/splitter

You can use an Ethernet cable or
connect wirelessly.
You can follow this diagram to connect your modem router, or follow the detailed instructions in this booklet.
3. Connect a computer.2. Power on the
4. Launch a browser.
Wait for the WiFi LED to light.
1. Connect to the Internet.
a. Install an ADSL microfilter between the phone line
If you do not see genie, type
www.routerlogin.net. Type admin
for the user name and password
as the password.
modem router.
NETGEAR genie displays.
Power
On/Off
and the phone.
b. Connect the DSL port of the modem router to the
ADSL port of the microfilter.
Internet
ADSL
microfilter
Support
Thank you for selecting NETGEAR products.
After installing your device, locate the serial number on the label of
your product and use it to register your product at
https://my.netgear.com.
You must register your product before you can use NETGEAR
telephone support. NETGEAR recommends registering your product
through the NETGEAR website.
For product updates and web support, visit
http://support.netgear.com.
NETGEAR recommends that you use only the official NETGEAR
support resources.
You can get the user manual online at
http://downloadcenter.netgear.com or through a link in the product’s
user interface.

1
Contents
Before You Begin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Install Your Modem Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
If NETGEAR genie Does Not Display . . . . . . . . . . . . . . . . . . . . 5
Preset Wireless Security . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Wireless Network Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Join the Wireless Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Access the Modem Router to Make Changes . . . . . . . . . . . . . . . . . 9
NETGEAR genie App . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Other Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Reset the Modem Router to Factory Settings . . . . . . . . . . . . . . . . . 12

2
Before You Begin
You can connect your modem router directly to a DSL line.
Note: Make sure that your DSL service is active before you install
the modem router. You need the information listed here to
install your DSL modem and connect to the Internet. Locate it
and have it on hand before you start the installation procedure.
•DSL user name and password. This information is included in
the welcome letter your DSL ISP sent you when you signed up for
your service. Record your DSL Internet service account user
name and password here:
•Your telephone number or DSL account number. If you do not
have voice service, you can use your DSL account number in
place of a phone number.
If you do not know or cannot locate your user name and password,
call your DSL Internet service provider.
Be specific when speaking with your DSL Internet service provider.
For example, you could say:
I need my DSL service user name and password. Can you help me?
Note: If your provider says that they do not support NETGEAR
services, tell them you need only your DSL user name and
password; you do not need support.
User name:
Password:

3
Install Your Modem Router
A microfilter filters DSL interference out of standard phone equipment
that shares the line with DSL service. Examples of devices are
telephones, fax machines, answering machines, and caller ID
displays.
To install your modem router:
1. Connect to the Internet.
a. Install an ADSL microfilter between the phone line and the
phone.
b. Connect the DSL port of the modem router to the ADSL port
of the microfilter.
c. Use an ADSL microfilter for every phone line in the house if
your modem router and telephone connect to the same
phone line.
Modem router
ADSL microfilter
Phone line outlet
DSL port

4
2. Power on the modem router.
a. Connect the power adapter to the modem router, and plug
the power adapter into an outlet.
b. Wait for the WiFi LED on the front panel to light.
c. If no LEDs are lit, press the Power On/Off button on the
rear panel of the modem router.
3. Connect a computer.
Power
On/Off
LAN port
Computer

5
You can use an Ethernet cable or connect wirelessly.
•For a wired connection, use an Ethernet cable to connect
your computer to an unused yellow Ethernet LAN port on
your modem router.
•To connect wirelessly, use the preset wireless security
settings on the label on the bottom of the modem router.
4. Launch a browser.
The first time that you connect to the modem router, the genie
screen displays. Follow the genie steps to connect to the Internet
If NETGEAR genie Does Not Display
•Close and reopen the browser. Type www.routerlogin.net in the
address bar, and type the user name admin and the default
password (password).
•Make sure that the computer is connected to one of the four LAN
Ethernet ports, or wirelessly to the modem router.
•Make sure that the modem router has power, and that its WiFi
LED is solid green.
•If the computer is set to a static or fixed IP address (this condition
is uncommon), change it to obtain an IP address automatically
from the modem router.

6
Preset Wireless Security
The modem router has a unique WiFi network name (SSID) and
network key (password). The default SSID and password are
uniquely generated for every device, like a serial number, to protect
and maximize your wireless security. This information is located on
the label on the bottom of the modem router.
NETGEAR recommends that you do not change the preset WiFi
SSID or password. If you do change the settings, the SSID and
password on the label no longer apply.
WiFi network name Network key
(password)(SSID)

7
Wireless Network Settings
Record the preset wireless settings on the label on the bottom of the
modem router in the space below for easy reference.
If you change the default settings, record them here for easy
reference and store this booklet in a safe place:
To retrieve or update your wireless password:
1. Type www.routerlogin.net in a web browser.
2. Log in using the user name (admin) and the default password
(password).
3. Select Wireless Settings.
WiFi network name (SSID):
Network key (password):
WiFi network name (SSID):
Network key (password):

8
Join the Wireless Network
You can use either the Wi-Fi Protected Setup (WPS) method or the
manual method to join your wireless network.
To join the network using WPS:
1. Press the WPS button on the modem router.
2. Within 2 minutes, press the WPS button on your wireless computer
or device, or follow the WPS instructions that came with your
wireless device to complete the WPS process.
Note: Some older wireless computers or devices cannot use WPS.
To join the network manually:
1. On your computer or wireless device, open the software that
manages its wireless connections.
This software scans for all wireless networks in your area.
2. Look for the WiFi network name (SSID) and select it.
The SSID is on the label on the bottom of the modem router.
3. If you changed the name of your network during the setup process,
look for that network name.
4. Enter the preset password (or your custom password if you
changed it).
5. Click Connect.