NETGEAR NIGHTHAWK M2 User manual
Quick Start
Next Gen Gigabit LTE Mobile Router
M2
Support
For additional information, visit netgear.com/support to access the full user manual
and to download firmware updates.
Compliance
For the current EU Declaration of Conformity, visit
http://kb.netgear.com/app/answers/detail/a_id/11621.
For regulatory compliance information, visit:
http://www.netgear.com/about/regulatory/.
LCD Status Bar Icons
Signal strength 1 bar. Low signal
5 bars. Strong signal
Network type 4G+, 4G
HSPA+ /DC HSPA
3G
Roaming Connected to a network other than your service
provider’s.
Traffic • Outline. Connected
• Solid. Sending or receiving
• None. Not connected
Battery This icon is solid when the battery is fully charged.
Battery hot while
charging
The battery is hot, but is being charged.
Battery hot,
not charging
The battery is too hot and is not being charged.
Alert To view system alerts, visit the mobile router’s home page
at http://m2login.net.
Download the NETGEAR Mobile app
Use the NETGEAR Mobile app to change your WiFi network
name and password. You can also use it to play and share media,
and enable the travel router feature.
1. Connect your mobile device to the Internet.
2. Download the NETGEAR Mobile app from
netgear.com/mobileapps.
Log in to the Nighthawk M2 mobile router
1. Launch a web browser from a device that is connected to the
Nighthawk M2 mobile router.
2. In the address field of the web browser, enter http://m2login.net or
http://192.168.1.1.
3. In the Sign In field, enter the admin password and click the Sign In button.
See the label located under the battery for the initial admin password. We
recommend that you change it to a password that you want to use.
Upload media files to the Nighthawk M2 mobile router
You can upload media files to a USB drive connected to the
Nighthawk M2 mobile router. USB drives are sold separately.
1. Log in to the Nighthawk M2 mobile router home page.
2. Click the MyMedia tab.
3. Drag and drop your files onto the page.
Use the Nighthawk M2 mobile router to charge devices
If the battery power is low on your smartphone or other device, you can give it a
boost by connecting it to the mobile router’s USB port (type A).
Jump boost begins automatically once the devices are connected. Note that Jump
boost is only supported when the mobile router contains a battery.
USB
(type A)
Specifications
Band Specication
LTE FDD 700/800/900/1800/2100/2600 MHz
LTD TDD 2300/2500/2600 MHz
3G 850/900/1900/2100 MHz
© NETGEAR, Inc., NETGEAR and the NETGEAR Logo and Nighthawk are trademarks of NETGEAR, Inc. Any non‑NETGEAR
trademarks are used for reference purposes only.
USB
(type C)
Antenna port
Ethernet port
(LAN or WAN)
Antenna port
Status
The mobile router LCD home screen and the LED show you its status. The
appearance of your home screen depends on the model.
NETGEAR INTL LTD
Building 3, University Technology Centre
Curraheen Road, Cork, Ireland April 2019
Connect your devices
1. Check to make sure that WiFi is enabled on your computer or mobile device
and search for WiFi networks.
Windows Click the Internet Access icon, which is usually found on
the bottom right side of your screen.
Mac Select WiFi > Network.
Mobile devices Tap Settings > WiFi
3. To view the WiFi name and password, press and release the Power button.
4. Select the WiFi name displayed on your Nighthawk M2 mobile router screen.
5. Enter the WiFi password exactly as it is displayed.
Note: Your password is case‑sensitive. We strongly recommend that you
change the default admin password.
6. To use the mobile router as an Internet gateway, connect an Ethernet device to
the Nighthawk M2 mobile router Ethernet port.
Set up the Nighthawk M2 mobile router
1. Press and hold the Power button for three
seconds.
After several seconds, a setup screen displays.
2. Follow the onscreen prompts to change the
SSID, passphrase, and admin password.
Although not required, we strongly recommend
you change the SSID, passphrase, and admin
password.
Note: You can also change these settings by
using the NETGEAR Mobile app, or by visiting
http://m2login.net or http://192.168.1.1 from a
device that is connected to the mobile router.
Power or wake the mobile router
To turn the mobile router on or off, press and hold the Power button for three
seconds.
To wake the router, press and release the Power button.
Check the SIM card and insert the battery
1. Locate the bottom cover in the envelope.
2. Check to see if a SIM card is in the SIM
card slot.
3. If a SIM card is not in the slot, locate the
SIM card.
To get a valid and provisioned SIM card,
contact your mobile provider.
4. Carefully slide the SIM card into the slot
with the gold contacts facing down.
5. Align the battery connectors and insert
the battery making sure the contact side
of the battery goes under the two plastic
tabs in the battery recess.
6. Attach the bottom cover.
SIM
card
Reset
button
Package contents
• Nighthawk M2 mobile router
• Battery
• Quick start guide
• Bottom cover
• USB Type‑C cable
• AC power adapter
• Safety information sheet
• EU Declaration of Conformity sheet
Note: The bottom cover, quick start guide, and the other documents are in an
envelope.
Power button
Home
Return
(go back)
LED Description
Slow blue blink The mobile router is ready.
Fast blue blink The mobile router is transferring data
Slow amber blink The mobile router is not ready.
Status
The mobile router LCD home screen and the LED show you its status. The
appearance of your home screen depends on the model.
NETGEAR INTL LTD
Building 3, University Technology Centre
Curraheen Road, Cork, Ireland April 2019
Connect your devices
1. Check to make sure that WiFi is enabled on your computer or mobile device
and search for WiFi networks.
Windows Click the Internet Access icon, which is usually found on
the bottom right side of your screen.
Mac Select WiFi > Network.
Mobile devices Tap Settings > WiFi
3. To view the WiFi name and password, press and release the Power button.
4. Select the WiFi name displayed on your Nighthawk M2 mobile router screen.
5. Enter the WiFi password exactly as it is displayed.
Note: Your password is case‑sensitive. We strongly recommend that you
change the default admin password.
6. To use the mobile router as an Internet gateway, connect an Ethernet device to
the Nighthawk M2 mobile router Ethernet port.
Set up the Nighthawk M2 mobile router
1. Press and hold the Power button for three
seconds.
After several seconds, a setup screen displays.
2. Follow the onscreen prompts to change the
SSID, passphrase, and admin password.
Although not required, we strongly recommend
you change the SSID, passphrase, and admin
password.
Note: You can also change these settings by
using the NETGEAR Mobile app, or by visiting
http://m2login.net or http://192.168.1.1 from a
device that is connected to the mobile router.
Power or wake the mobile router
To turn the mobile router on or off, press and hold the Power button for three
seconds.
To wake the router, press and release the Power button.
Check the SIM card and insert the battery
1. Locate the bottom cover in the envelope.
2. Check to see if a SIM card is in the SIM
card slot.
3. If a SIM card is not in the slot, locate the
SIM card.
To get a valid and provisioned SIM card,
contact your mobile provider.
4. Carefully slide the SIM card into the slot
with the gold contacts facing down.
5. Align the battery connectors and insert
the battery making sure the contact side
of the battery goes under the two plastic
tabs in the battery recess.
6. Attach the bottom cover.
SIM
card
Reset
button
Package contents
• Nighthawk M2 mobile router
• Battery
• Quick start guide
• Bottom cover
• USB Type‑C cable
• AC power adapter
• Safety information sheet
• EU Declaration of Conformity sheet
Note: The bottom cover, quick start guide, and the other documents are in an
envelope.
Power button
Home
Return
(go back)
LED Description
Slow blue blink The mobile router is ready.
Fast blue blink The mobile router is transferring data
Slow amber blink The mobile router is not ready.
Status
The mobile router LCD home screen and the LED show you its status. The
appearance of your home screen depends on the model.
NETGEAR INTL LTD
Building 3, University Technology Centre
Curraheen Road, Cork, Ireland April 2019
Connect your devices
1. Check to make sure that WiFi is enabled on your computer or mobile device
and search for WiFi networks.
Windows Click the Internet Access icon, which is usually found on
the bottom right side of your screen.
Mac Select WiFi > Network.
Mobile devices Tap Settings > WiFi
3. To view the WiFi name and password, press and release the Power button.
4. Select the WiFi name displayed on your Nighthawk M2 mobile router screen.
5. Enter the WiFi password exactly as it is displayed.
Note: Your password is case‑sensitive. We strongly recommend that you
change the default admin password.
6. To use the mobile router as an Internet gateway, connect an Ethernet device to
the Nighthawk M2 mobile router Ethernet port.
Set up the Nighthawk M2 mobile router
1. Press and hold the Power button for three
seconds.
After several seconds, a setup screen displays.
2. Follow the onscreen prompts to change the
SSID, passphrase, and admin password.
Although not required, we strongly recommend
you change the SSID, passphrase, and admin
password.
Note: You can also change these settings by
using the NETGEAR Mobile app, or by visiting
http://m2login.net or http://192.168.1.1 from a
device that is connected to the mobile router.
Power or wake the mobile router
To turn the mobile router on or off, press and hold the Power button for three
seconds.
To wake the router, press and release the Power button.
Check the SIM card and insert the battery
1. Locate the bottom cover in the envelope.
2. Check to see if a SIM card is in the SIM
card slot.
3. If a SIM card is not in the slot, locate the
SIM card.
To get a valid and provisioned SIM card,
contact your mobile provider.
4. Carefully slide the SIM card into the slot
with the gold contacts facing down.
5. Align the battery connectors and insert
the battery making sure the contact side
of the battery goes under the two plastic
tabs in the battery recess.
6. Attach the bottom cover.
SIM
card
Reset
button
Package contents
• Nighthawk M2 mobile router
• Battery
• Quick start guide
• Bottom cover
• USB Type‑C cable
• AC power adapter
• Safety information sheet
• EU Declaration of Conformity sheet
Note: The bottom cover, quick start guide, and the other documents are in an
envelope.
Power button
Home
Return
(go back)
LED Description
Slow blue blink The mobile router is ready.
Fast blue blink The mobile router is transferring data
Slow amber blink The mobile router is not ready.
Status
The mobile router LCD home screen and the LED show you its status. The
appearance of your home screen depends on the model.
NETGEAR INTL LTD
Building 3, University Technology Centre
Curraheen Road, Cork, Ireland April 2019
Connect your devices
1. Check to make sure that WiFi is enabled on your computer or mobile device
and search for WiFi networks.
Windows Click the Internet Access icon, which is usually found on
the bottom right side of your screen.
Mac Select WiFi > Network.
Mobile devices Tap Settings > WiFi
3. To view the WiFi name and password, press and release the Power button.
4. Select the WiFi name displayed on your Nighthawk M2 mobile router screen.
5. Enter the WiFi password exactly as it is displayed.
Note: Your password is case‑sensitive. We strongly recommend that you
change the default admin password.
6. To use the mobile router as an Internet gateway, connect an Ethernet device to
the Nighthawk M2 mobile router Ethernet port.
Set up the Nighthawk M2 mobile router
1. Press and hold the Power button for three
seconds.
After several seconds, a setup screen displays.
2. Follow the onscreen prompts to change the
SSID, passphrase, and admin password.
Although not required, we strongly recommend
you change the SSID, passphrase, and admin
password.
Note: You can also change these settings by
using the NETGEAR Mobile app, or by visiting
http://m2login.net or http://192.168.1.1 from a
device that is connected to the mobile router.
Power or wake the mobile router
To turn the mobile router on or off, press and hold the Power button for three
seconds.
To wake the router, press and release the Power button.
Check the SIM card and insert the battery
1. Locate the bottom cover in the envelope.
2. Check to see if a SIM card is in the SIM
card slot.
3. If a SIM card is not in the slot, locate the
SIM card.
To get a valid and provisioned SIM card,
contact your mobile provider.
4. Carefully slide the SIM card into the slot
with the gold contacts facing down.
5. Align the battery connectors and insert
the battery making sure the contact side
of the battery goes under the two plastic
tabs in the battery recess.
6. Attach the bottom cover.
SIM
card
Reset
button
Package contents
• Nighthawk M2 mobile router
• Battery
• Quick start guide
• Bottom cover
• USB Type‑C cable
• AC power adapter
• Safety information sheet
• EU Declaration of Conformity sheet
Note: The bottom cover, quick start guide, and the other documents are in an
envelope.
Power button
Home
Return
(go back)
LED Description
Slow blue blink The mobile router is ready.
Fast blue blink The mobile router is transferring data
Slow amber blink The mobile router is not ready.
Status
The mobile router LCD home screen and the LED show you its status. The
appearance of your home screen depends on the model.
NETGEAR INTL LTD
Building 3, University Technology Centre
Curraheen Road, Cork, Ireland April 2019
Connect your devices
1. Check to make sure that WiFi is enabled on your computer or mobile device
and search for WiFi networks.
Windows Click the Internet Access icon, which is usually found on
the bottom right side of your screen.
Mac Select WiFi > Network.
Mobile devices Tap Settings > WiFi
3. To view the WiFi name and password, press and release the Power button.
4. Select the WiFi name displayed on your Nighthawk M2 mobile router screen.
5. Enter the WiFi password exactly as it is displayed.
Note: Your password is case‑sensitive. We strongly recommend that you
change the default admin password.
6. To use the mobile router as an Internet gateway, connect an Ethernet device to
the Nighthawk M2 mobile router Ethernet port.
Set up the Nighthawk M2 mobile router
1. Press and hold the Power button for three
seconds.
After several seconds, a setup screen displays.
2. Follow the onscreen prompts to change the
SSID, passphrase, and admin password.
Although not required, we strongly recommend
you change the SSID, passphrase, and admin
password.
Note: You can also change these settings by
using the NETGEAR Mobile app, or by visiting
http://m2login.net or http://192.168.1.1 from a
device that is connected to the mobile router.
Power or wake the mobile router
To turn the mobile router on or off, press and hold the Power button for three
seconds.
To wake the router, press and release the Power button.
Check the SIM card and insert the battery
1. Locate the bottom cover in the envelope.
2. Check to see if a SIM card is in the SIM
card slot.
3. If a SIM card is not in the slot, locate the
SIM card.
To get a valid and provisioned SIM card,
contact your mobile provider.
4. Carefully slide the SIM card into the slot
with the gold contacts facing down.
5. Align the battery connectors and insert
the battery making sure the contact side
of the battery goes under the two plastic
tabs in the battery recess.
6. Attach the bottom cover.
SIM
card
Reset
button
Package contents
• Nighthawk M2 mobile router
• Battery
• Quick start guide
• Bottom cover
• USB Type‑C cable
• AC power adapter
• Safety information sheet
• EU Declaration of Conformity sheet
Note: The bottom cover, quick start guide, and the other documents are in an
envelope.
Power button
Home
Return
(go back)
LED Description
Slow blue blink The mobile router is ready.
Fast blue blink The mobile router is transferring data
Slow amber blink The mobile router is not ready.
Quick Start
Next Gen Gigabit LTE Mobile Router
M2
Support
For additional information, visit netgear.com/support to access the full user manual
and to download firmware updates.
Compliance
For the current EU Declaration of Conformity, visit
http://kb.netgear.com/app/answers/detail/a_id/11621.
For regulatory compliance information, visit:
http://www.netgear.com/about/regulatory/.
LCD Status Bar Icons
Signal strength 1 bar. Low signal
5 bars. Strong signal
Network type 4G+, 4G
HSPA+ /DC HSPA
3G
Roaming Connected to a network other than your service
provider’s.
Traffic • Outline. Connected
• Solid. Sending or receiving
• None. Not connected
Battery This icon is solid when the battery is fully charged.
Battery hot while
charging
The battery is hot, but is being charged.
Battery hot,
not charging
The battery is too hot and is not being charged.
Alert To view system alerts, visit the mobile router’s home page
at http://m2login.net.
Download the NETGEAR Mobile app
Use the NETGEAR Mobile app to change your WiFi network
name and password. You can also use it to play and share media,
and enable the travel router feature.
1. Connect your mobile device to the Internet.
2. Download the NETGEAR Mobile app from
netgear.com/mobileapps.
Log in to the Nighthawk M2 mobile router
1. Launch a web browser from a device that is connected to the
Nighthawk M2 mobile router.
2. In the address field of the web browser, enter http://m2login.net or
http://192.168.1.1.
3. In the Sign In field, enter the admin password and click the Sign In button.
See the label located under the battery for the initial admin password. We
recommend that you change it to a password that you want to use.
Upload media files to the Nighthawk M2 mobile router
You can upload media files to a USB drive connected to the
Nighthawk M2 mobile router. USB drives are sold separately.
1. Log in to the Nighthawk M2 mobile router home page.
2. Click the MyMedia tab.
3. Drag and drop your files onto the page.
Use the Nighthawk M2 mobile router to charge devices
If the battery power is low on your smartphone or other device, you can give it a
boost by connecting it to the mobile router’s USB port (type A).
Jump boost begins automatically once the devices are connected. Note that Jump
boost is only supported when the mobile router contains a battery.
USB
(type A)
Specifications
Band Specication
LTE FDD 700/800/900/1800/2100/2600 MHz
LTD TDD 2300/2500/2600 MHz
3G 850/900/1900/2100 MHz
© NETGEAR, Inc., NETGEAR and the NETGEAR Logo and Nighthawk are trademarks of NETGEAR, Inc. Any non‑NETGEAR
trademarks are used for reference purposes only.
USB
(type C)
Antenna port
Ethernet port
(LAN or WAN)
Antenna port
Quick Start
Next Gen Gigabit LTE Mobile Router
M2
Support
For additional information, visit netgear.com/support to access the full user manual
and to download firmware updates.
Compliance
For the current EU Declaration of Conformity, visit
http://kb.netgear.com/app/answers/detail/a_id/11621.
For regulatory compliance information, visit:
http://www.netgear.com/about/regulatory/.
LCD Status Bar Icons
Signal strength 1 bar. Low signal
5 bars. Strong signal
Network type 4G+, 4G
HSPA+ /DC HSPA
3G
Roaming Connected to a network other than your service
provider’s.
Traffic • Outline. Connected
• Solid. Sending or receiving
• None. Not connected
Battery This icon is solid when the battery is fully charged.
Battery hot while
charging
The battery is hot, but is being charged.
Battery hot,
not charging
The battery is too hot and is not being charged.
Alert To view system alerts, visit the mobile router’s home page
at http://m2login.net.
Download the NETGEAR Mobile app
Use the NETGEAR Mobile app to change your WiFi network
name and password. You can also use it to play and share media,
and enable the travel router feature.
1. Connect your mobile device to the Internet.
2. Download the NETGEAR Mobile app from
netgear.com/mobileapps.
Log in to the Nighthawk M2 mobile router
1. Launch a web browser from a device that is connected to the
Nighthawk M2 mobile router.
2. In the address field of the web browser, enter http://m2login.net or
http://192.168.1.1.
3. In the Sign In field, enter the admin password and click the Sign In button.
See the label located under the battery for the initial admin password. We
recommend that you change it to a password that you want to use.
Upload media files to the Nighthawk M2 mobile router
You can upload media files to a USB drive connected to the
Nighthawk M2 mobile router. USB drives are sold separately.
1. Log in to the Nighthawk M2 mobile router home page.
2. Click the MyMedia tab.
3. Drag and drop your files onto the page.
Use the Nighthawk M2 mobile router to charge devices
If the battery power is low on your smartphone or other device, you can give it a
boost by connecting it to the mobile router’s USB port (type A).
Jump boost begins automatically once the devices are connected. Note that Jump
boost is only supported when the mobile router contains a battery.
USB
(type A)
Specifications
Band Specication
LTE FDD 700/800/900/1800/2100/2600 MHz
LTD TDD 2300/2500/2600 MHz
3G 850/900/1900/2100 MHz
© NETGEAR, Inc., NETGEAR and the NETGEAR Logo and Nighthawk are trademarks of NETGEAR, Inc. Any non‑NETGEAR
trademarks are used for reference purposes only.
USB
(type C)
Antenna port
Ethernet port
(LAN or WAN)
Antenna port
Quick Start
Next Gen Gigabit LTE Mobile Router
M2
Support
For additional information, visit netgear.com/support to access the full user manual
and to download firmware updates.
Compliance
For the current EU Declaration of Conformity, visit
http://kb.netgear.com/app/answers/detail/a_id/11621.
For regulatory compliance information, visit:
http://www.netgear.com/about/regulatory/.
LCD Status Bar Icons
Signal strength 1 bar. Low signal
5 bars. Strong signal
Network type 4G+, 4G
HSPA+ /DC HSPA
3G
Roaming Connected to a network other than your service
provider’s.
Traffic • Outline. Connected
• Solid. Sending or receiving
• None. Not connected
Battery This icon is solid when the battery is fully charged.
Battery hot while
charging
The battery is hot, but is being charged.
Battery hot,
not charging
The battery is too hot and is not being charged.
Alert To view system alerts, visit the mobile router’s home page
at http://m2login.net.
Download the NETGEAR Mobile app
Use the NETGEAR Mobile app to change your WiFi network
name and password. You can also use it to play and share media,
and enable the travel router feature.
1. Connect your mobile device to the Internet.
2. Download the NETGEAR Mobile app from
netgear.com/mobileapps.
Log in to the Nighthawk M2 mobile router
1. Launch a web browser from a device that is connected to the
Nighthawk M2 mobile router.
2. In the address field of the web browser, enter http://m2login.net or
http://192.168.1.1.
3. In the Sign In field, enter the admin password and click the Sign In button.
See the label located under the battery for the initial admin password. We
recommend that you change it to a password that you want to use.
Upload media files to the Nighthawk M2 mobile router
You can upload media files to a USB drive connected to the
Nighthawk M2 mobile router. USB drives are sold separately.
1. Log in to the Nighthawk M2 mobile router home page.
2. Click the MyMedia tab.
3. Drag and drop your files onto the page.
Use the Nighthawk M2 mobile router to charge devices
If the battery power is low on your smartphone or other device, you can give it a
boost by connecting it to the mobile router’s USB port (type A).
Jump boost begins automatically once the devices are connected. Note that Jump
boost is only supported when the mobile router contains a battery.
USB
(type A)
Specifications
Band Specication
LTE FDD 700/800/900/1800/2100/2600 MHz
LTD TDD 2300/2500/2600 MHz
3G 850/900/1900/2100 MHz
© NETGEAR, Inc., NETGEAR and the NETGEAR Logo and Nighthawk are trademarks of NETGEAR, Inc. Any non‑NETGEAR
trademarks are used for reference purposes only.
USB
(type C)
Antenna port
Ethernet port
(LAN or WAN)
Antenna port
Quick Start
Next Gen Gigabit LTE Mobile Router
M2
Support
For additional information, visit netgear.com/support to access the full user manual
and to download firmware updates.
Compliance
For the current EU Declaration of Conformity, visit
http://kb.netgear.com/app/answers/detail/a_id/11621.
For regulatory compliance information, visit:
http://www.netgear.com/about/regulatory/.
LCD Status Bar Icons
Signal strength 1 bar. Low signal
5 bars. Strong signal
Network type 4G+, 4G
HSPA+ /DC HSPA
3G
Roaming Connected to a network other than your service
provider’s.
Traffic • Outline. Connected
• Solid. Sending or receiving
• None. Not connected
Battery This icon is solid when the battery is fully charged.
Battery hot while
charging
The battery is hot, but is being charged.
Battery hot,
not charging
The battery is too hot and is not being charged.
Alert To view system alerts, visit the mobile router’s home page
at http://m2login.net.
Download the NETGEAR Mobile app
Use the NETGEAR Mobile app to change your WiFi network
name and password. You can also use it to play and share media,
and enable the travel router feature.
1. Connect your mobile device to the Internet.
2. Download the NETGEAR Mobile app from
netgear.com/mobileapps.
Log in to the Nighthawk M2 mobile router
1. Launch a web browser from a device that is connected to the
Nighthawk M2 mobile router.
2. In the address field of the web browser, enter http://m2login.net or
http://192.168.1.1.
3. In the Sign In field, enter the admin password and click the Sign In button.
See the label located under the battery for the initial admin password. We
recommend that you change it to a password that you want to use.
Upload media files to the Nighthawk M2 mobile router
You can upload media files to a USB drive connected to the
Nighthawk M2 mobile router. USB drives are sold separately.
1. Log in to the Nighthawk M2 mobile router home page.
2. Click the MyMedia tab.
3. Drag and drop your files onto the page.
Use the Nighthawk M2 mobile router to charge devices
If the battery power is low on your smartphone or other device, you can give it a
boost by connecting it to the mobile router’s USB port (type A).
Jump boost begins automatically once the devices are connected. Note that Jump
boost is only supported when the mobile router contains a battery.
USB
(type A)
Specifications
Band Specication
LTE FDD 700/800/900/1800/2100/2600 MHz
LTD TDD 2300/2500/2600 MHz
3G 850/900/1900/2100 MHz
© NETGEAR, Inc., NETGEAR and the NETGEAR Logo and Nighthawk are trademarks of NETGEAR, Inc. Any non‑NETGEAR
trademarks are used for reference purposes only.
USB
(type C)
Antenna port
Ethernet port
(LAN or WAN)
Antenna port
Table of contents
Other NETGEAR Wireless Router manuals
NETGEAR
NETGEAR DGN1000 - Wireless-N Router With Built-in DSL... User manual
NETGEAR
NETGEAR WGR614 User manual
NETGEAR
NETGEAR WPN824v3 - RangeMax Wireless Router User manual
NETGEAR
NETGEAR N300 WNR2000v5 User manual
NETGEAR
NETGEAR DGND3300v2 - RangeMax Dual Band Wireless-N Modem... User manual
NETGEAR
NETGEAR WNR3500Lv2 User manual
NETGEAR
NETGEAR RangeMax NEXT WNR854T User manual
NETGEAR
NETGEAR DG834G User manual
NETGEAR
NETGEAR JNR3000 User manual
NETGEAR
NETGEAR Nighthawk RS700 User manual
NETGEAR
NETGEAR 4G User manual
NETGEAR
NETGEAR WGR826V User manual
NETGEAR
NETGEAR WNDR4300 User manual
NETGEAR
NETGEAR CENTRIA WNDR4720 User manual
NETGEAR
NETGEAR Verizon Jetpack AC791L User manual
NETGEAR
NETGEAR Nighthawk RAX40v2 User manual
NETGEAR
NETGEAR 8NE10325070 User manual
NETGEAR
NETGEAR WNDRMAC User manual
NETGEAR
NETGEAR R7500 User manual
NETGEAR
NETGEAR DGND3300v2 - RangeMax Dual Band Wireless-N Modem... User manual
