netta BG-40B User manual

GLASS PANEL
FIREPLACE
-------------------------------------------------------------------------------------------------
EN USER INSTRUCTION & OPERATION MANUAL
ES MANUAL DE INSTRUCCIONES Y OPERACIONES PARA EL
USUARIO
DE BENUTZERANLEITUNG & BETRIEBSANLEITUNG
FR MANUEL D'UTILISATION ET D'UTILISATION
IT ISTRUZIONI PER L'USO E MANUALE OPERATIVO
STYLE
WALL-MOUNTED
OR RECESSED
RATED POWER
1400-1600W
TIMER
WEEKLY
REMOTE
CONTROL
INCLUDED
EN

Thank you for purchasing this NETTA product.
Please read the user manual carefully before operating this
appliance.
We will update our instruction manuals if necessary.
For the most up-to-date user manual, please visit our official
website: www.nettadirect.com.
You can download a copy of up-to-date user manuals at any time
in electronic format. We do not supply you with a paper-based
user manual after each revision.
Require a larger version of this
Instruction Manual?
Please download electronically
from our website and use PDF
reader on your device to enlarge
the text if needed.
www.nettadirect.com

Safety and Warnings
Intended Use
NETTA Design is for domestic and
indoor use only. This product is not
intended for use by people who have
lack of experience and knowledge or
have reduced ability, or sensory and
mental capabilities.
General Warnings
•Read all instructions before using this heater.
•Ensure the plug is connected to the mains socket securely.
•This heater is hot when in use. To avoid burning yourself, do not
touch the hot surfaces. Use the handles provided when moving
this heater.
•Keep combustible materials such as furniture, pillows, bedding,
papers, clothes and curtains at least 1m from the front of the
heater and away from the sides and rear. In order to avoid
overheating, do not cover the heater.
•Extreme caution is necessary when any heater is used near
children and/or when the heater is left operating and unattended.
•Always unplug the heater when it is not in use.
•Do not operate any heater with a damaged cord or plug, after the
heater malfunctions or after it has been dropped or damaged. In
this case, contact your retailer for their replacement/repair service.
•This heater is for indoor use only. Do not use outdoors.
•This heater is not intended for bathrooms, laundry areas or similar
indoor locations. Never locate the heater where it may come into
contact with water/liquid.
•Do not run the cord under carpeting, rugs, or similar coverings.
•Place the cord away from busy areas where it may become a trip
hazard.
Regular Check-Ups
Ensure the power cable and
plug are not damaged before
plugging into a socket.
Check all the buttons are
functioning correctly.

General Warnings
•Do not insert or allow foreign objects to enter any ventilation or
exhaust opening as this may cause an electric shock, fire or
damage the heater.
•To prevent a potential fire, do not block the air intakes or exhausts
in any manner. Do not use on soft surfaces, such as a bed, where
openings may become blocked.
•The heater has hot and sparking parts inside. Do not use it in areas
where gasoline, or similar flammable liquids, are used or stored.
•Use the heater only as described in this manual. Any other use not
recommended by the manufacturer may cause fire, electric shock
or injury as well as voiding your warranty.
•High temperatures may be generated under certain abnormal
conditions. Do not partially or fully cover/obstruct the front of this
heater.
•The replacement of the lamps should only be done when the heater
is disconnected from the supply circuit.
•This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety.
•Children should be supervised to ensure that they do not play with
the appliance.
•In order to avoid a hazard due to the inadvertent re-setting of the
thermal cut-out, this appliance must not be supplied through an
external switching device, such as a timer, or connected to a circuit
that is regularly switched on and off by the utility.
•To disconnect the heater, turn the controls to off, then remove the
plug from the socket.
When using electric appliances, basic precautions
should always be followed to reduce the risk of fire,
electric shock and injury to persons.

Assembling the Product
This product is constructed with a glass panel. Always use
extreme caution when handling glass. Failure to do so could
result in personal injury or property damage.
Remove all parts and hardware from the carton and place them on a
clean, soft and dry surface. Parts and assembly steps are grouped for
wall-hanging or recessing use. Check the parts list to make sure
nothing is missing. If disposing of the packaging, please recycle where
possible.
You will need the following tools (not included):
•Phillips Screwdriver
•Stud Finder
•Spirit Level
•Tape Measure
•Electric Drill
•¼” Wood Drill Bit
•Hammer

Your appliance is a wall-mounted/recessed/mantel installation. Select a
suitable location to install it that is not susceptible to moisture and is
away from drapes, furniture and high-traffic areas.
Note: Follow all national and local electrical codes.

Recessed To Wall Installation
A. Select an area of dry wall to create a framing hole for the
fireplace. The size of hole needed can be found on the chart
below. (Fig. A).
B. Fix the three wall anchors to each side of the fireplace
according to the dimensions shown on the drawing. (Fig. B).
C. Remove the two screws in both sides of the glass panel.
(Fig. C (Next Page)).

D. Have two people remove the glass panel from the front of the
fireplace. Place it onto a soft and clean place. (Fig. D).
E. Have two people move the fireplace to the wall hole.
If the appliance is fully recessed into the wall:
•Use the 6 screws (provided) to lock the appliance into the wall
with the existing two side flanges. (Fig. E).
•Re-install the glass panel when the fireplace is installed.

If the appliance is partially recessed into the wall:
•Use the four mounting metal brackets (provided) to lock the
appliance to the wall. (Fig. F).
•Note: Use the existing holes on the sides of the appliance for
recessing into a wall.
F. The fireplace should now look like this after installation.
(Fig. G).
Wall-Mounted Installation
Due to the many different materials used on different walls, it is
highly recommended that you consult your local builder before
you install this appliance on the wall.
A. Select a location that is not prone to moisture and is located
at least 36” (91cm) away from combustible materials such as
curtains, furniture or bedding.
B. Have two people hold the appliance against the wall to
determine the final location.

C. Place the unit face down on a soft, non-abrasive surface.
Remove the bracket from the back of the unit by removing the
screws (See Fig. 1).
D. Mark out the location, then mount the bracket(s) onto the wall
using the supplied screws. This bracket MUST have the
hooks facing upward and be level.
Note: It is strongly recommended that the mounting bracket
(E) be screwed into the wall studs where possible. If the wall
studs cannot be used, ensure that the supplied plastic
anchors are used to affix the bracket to the wall and the
bracket is adequately secured.
E. With the wall-mounting bracket installed, have two people lift
the appliance up and insert the two hooks on the bracket into
the two slots on the back of the appliance.
F. Check the appliance for stability ensuring that the bracket will
not pull free from the wall.
For 40”, 50”, 60”
models.
Fig. 1

Log/Crystal/Pebble Ember Installation
A. The appliance must be mounted in its final location with the
front glass removed before installing the logs/crystal/pebble
embers.
B. To install the logs, remove the logs from its packaging and
insert it into the fireplace (Fig. 1).
C. To install the crystals or pebbles, place the plastic tray (Part -
I (Parts and Hardware)) in the allotted space before carefully
placing the crystal or pebble embers into the bottom tray at
the front of the appliance as illustrated. Apply an even layer
from side to side. (Fig 2 and 3).
D. Crystal or pebble embers may have a fine oil residue that
needs to be cleaned prior to installation. Clean them with a
mild dish soap, rinse them thoroughly and allow to dry before
placing into the tray.
For 72” model.

Operating the Product
This electric fireplace can be operated by the control panel,
located on the bottom right-hand side of the glass panel, or by
the battery-powered remote control. The operation and functions
of the two methods are the same.
Before operating, please review the General Warnings at the
beginning of this manual.

Touch Control Panel Operation

Remote Control Operation

Timer Settings on Remote Control
Set Current Day and Time
1. Press once. When “MON” (Monday) begins flashing,
use to select the current day.
2. Press . When the hour digits begin flashing, use to
select the current hour.

3. Press again. When the minute digits begin flashing, use
to select the current minute.
4. Press again. The current time is now set.
Set ON/OFF Time and Temperature on a 7-Day Weekly Cycle
Ensure the fireplace is switched on before starting this process.
1. Press . When “MON” begins flashing, press 3 times.
When “ON” begins flashing, use to select the desired hour
and minute for the heater to turn on.
Note: The timer can only be adjusted in 30-minute
increments (i.e., 00:00-00:30; 00:30-01:00, etc).
2. Press . When “OFF” begins flashing, use to select the
desired hour and minute for the heater to turn off.
3. Press again. When “18” begins flashing, use to set
the desired temperature for Monday. Note: If a temperature
was previously set, those digits will be displayed instead of
“18”.
4. Press again. When “TUE” appears on the screen and
“ON” begins flashing, use to select the desired hour and
minute for the heater to turn on every Tuesday.
5. Press again. When “OFF” begins flashing, use to
select the desired hour and minute for the heater to turn off
every Tuesday.

6. Press again. When “18” begins flashing, use to
select the desired temperature for Tuesday.
7. Repeat steps 4 to 6 to set the “ON/OFF” time and
temperature for the remaining days.
8. Make sure the fireplace is on (if it’s not already) and
press to complete the programming, ensuring you aim
the remote control at the receiver, located in the middle of the
appliance. The appliance will “beep” once to confirm that
the programming has been successful.
9. Please note that the heater will need to be switched on
before you can complete the programming. If the heater is
off, you will not hear a beep and the timer will not be set.
Set ON/OFF Time and Temperature for a Specific Day(s)
Ensure the fireplace is switched on before starting this process.
1. If you wish to set the timer for a specific day(s), press
and then press for as many times needed before you
reach the required day. Follow steps 1, 2 and 3 to set the
timer and the temperature.
2. Ensure the fireplace is turned on (if it’s not already) and press
to set the programming. The appliance will “beep” once to
confirm that the programming has been successful. Once set,
you can turn the fireplace off.
Press at any time to clear the digits and turn the timer
settings off.

Open Window Warning
If the room temperature decreases by 10 degrees within 3
minutes, the appliance will assume there is an open window
nearby. In order to conserve energy, the heater will automatically
switch from High Heat to Low Heat, or if the heater is already set
to Low Heat, it will turn off completely.
When switching from High Heat to Low Heat, the appliance will
beep 3 times and the digital display will flash “88” 3 times before
displaying the existing heating status.
When switching from Low Heat to Off, the appliance will beep 3
times and the digital display will flash “88” continuously.
To reset the heating function, see the “Remote Control
Operation” section.
Note: When the heater is first turned on, a slight odour may
be present. This is normal and should not occur again
unless the heater is not used for a long period of time.
Note: To improve operation, aim the remote control at the
front of the fireplace. Do not press the buttons too quickly.
Give the unit time to respond to each command.

Temperature Limiting Control
This heater is equipped with a temperature limiting control.
Should the heater reach an unsafe temperature, the heater will
automatically turn off. To reset:
1. Unplug the power cord from the socket.
2. Turn the On/Off switch on the control panel to off and wait 5
minutes.
3. Inspect the fireplace to make sure no vents are blocked or
clogged with dust. If they are, use a vacuum to clean the
vents.
4. With the power switch in the Off position, plug the power cord
back into the socket.
5. If the problem continues, have your sockets and wiring
inspected by a professional.
Remote Control Battery Information
This remote control uses 2 AAA batteries (not included).
Always dispose of batteries in a safe way. Contact your
council or local recycling centre for more information on
battery disposal.

Cleaning, Maintenance and Storage
•Always turn the heater OFF and unplug the power cord from
the socket before cleaning, performing maintenance, or
moving this fireplace. Failure to do so could result in electric
shock, fire, or personal injury.
•Never immerse in water or spray with water. Doing so could
result in electric shock, fire, or personal injury.
Metal:
•Buff using a soft cloth, slightly dampened with a citrus oil-
based product.
•Do not use brass polish or household cleaners as these
products will damage the metal trim.
Glass:
•Use a good quality glass cleaner sprayed onto a cloth or towel.
Dry the glass panel with a paper towel or lint-free cloth.
•Never use abrasive cleaners, liquid sprays, or any cleaner that
could scratch the surface.
Vents:
•Use a vacuum or duster to remove dust and dirt from the
heater and vent areas.
Plastic:
•Wipe gently with a slightly damp cloth and a mild solution of
dish soap and warm water.
•Never use abrasive cleaners, liquid sprays, or any cleaner that
could scratch the surface.