Nextar W3G - W3G LCD Color Touch Screen Portable... User manual

1
POWER SUPPLY:
Connect the supplied adapter to the side of the unit in the slot marked “DC 5V IN”. Plug
the two-prong end of the power cord to an AC100-240V outlet. If you have difficulty
inserting the plug, turn it over and reinsert it. If the unit will not be used for a long time,
disconnect the plug from the outlet.
NOTE:
Before plugging the power cord into an AC outlet, make sure that all the connections
have been made.
CAUTION: These servicing instructions are for use by qualified service personnel only.
To reduce the risk of electric shock, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so.
Refer to service manual for servicing instructions. To reduce the risk of fire or electric
shock, do not expose this apparatus to rain or moisture.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NO
T
REMOVE COVER (OR BACK). NO USE-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to constitute
a risk of electric to
p
ersons.
The exclamation point within an equilateral triangle is intended to alert the use
r
to the presence of important operating and maintenance (servicing)
instructions in the literature accompan
y
in
g
the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OF MOISTURE.
Important
S
a
f
ety
Instructions

2
NOTES
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with a damp cloth.
7) Do not block any of the ventilation openings. Install in accordance with the
manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. Apolarized plug
has two blades with one wider than the other. A grounding type plug has two blades and
a third grounding prong. The wide blade or the third prong is provided for your safety.
When the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with a cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is damaged,
liquid has been spilled or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
15) Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids,
such as vases, shall be placed on the apparatus.
Important
S
a
f
ety
Instructions

3
Warning
Failure to avoid the following potentially hazardous situations may result in injury or
property damage.
The unit is designed to provide you with route suggestions. It does not reflect road
closures or road conditions, traffic congestion, weather conditions, or other factors that
may affect safety or timing while driving.
Use the unit only as a navigational aid. Do not attempt to use the unit for any purpose
requiring precise measurement of direction, distance, location, or topography. This
product should not be used to determine ground proximity for aircraft navigation.
CAUTION:
Danger of explosion if battery is incorrectly replaced. Replace only with the same or
equivalent type.
The batteries (or batteries installed) shall not be exposed to excessive heat such as
sunshine, fire or the like.
Underwriters Laboratories Inc. (“UL”) has not tested the performance or reliability of the
Global Positioning System (“GPS”) hardware, operating software or other aspects of this
product. UL has only tested for fire, shock or casualty hazards as outlined in UL’s
Standard(s) for Safety [Note-Consider referencing specific UL standard].
UL Certification does not cover the performance or reliability of the GPS hardware and
GPS operating software.
UL MAKES NO REPRESENTATIONS, WARRANTIES OR CERTIFICATIONS
WHATSOEVER REGARDING THE PERFORMANCE OR RELIABILITY OF ANY GPS
RELATED FUNCTIONS OF THIS PRODUCT.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Cleaning of touch screen
If touch screen has fingerprints or dust on it, lightly wipe the touch screen with dry soft
cloth (or similar).
Never use record cleaning sprays, benzene, thinner, static electricity prevention liquids
or any other solvents to clean your touch screen.
Important
S
a
f
ety
Instructions

4
Navigation Function
Other Special Functions
Navigation Function: The unit is designed to provide you with route suggestions. It supports voice
navi
g
ation.
Power Adapter Switch: Automaticall
y
adapts to voltage requirements in U.S and
other countries.
SD Card and USB Input:The unit is
designed with SD card and USB ports and
can be connected to SD card or other USB
device for file loading.
Flash Storage: Built in Flash Storage can
store map data. Support file formats: Supports MP3 Format files playback.
Features

5
Accessories List
ITEM NAME QTY
Owner’s Manual 2
Power Adaptor 1
Car Adaptor 1
USB Cable 1
Windshield mount bracket 1
Mount cradle 1
Dashboard mount disk 1
Pouch 1
NOTE
Accessories and their part number are subject to modification without prior notice due to
improvements.
Accessories

6
……………………………………….……..1
……………………………………………...4
……………………………………………...5
……………………………………………...7
……………………………………….……..9
………………………………………....….11
………………………………………..…..13
………………………………………..…..17
………………………………………....…19
………………………………………..…..20
………………………………………..…..21
Important Safety Instructions
Features
System Connections
Power Supply Preparation
Troubleshooting
General Setup
Specifications
A
ccessories
View of Main Unit
Playing Music
Use of the Mount Accessories
Contents

7
Front View
1. MENU button
Press to enter the main menu.
2. Speakers
3. POWER button
Press to enter or exit the standby mode.
4. Charge Indicator
When charging the battery, it is red; when the battery is fully charged, it turns green.
5. LCD Screen
View of Main Unit

8
Side View
Rear View
1. ON/OFF switch
Used to switch power on or off.
2. GPS Antenna
Receiving GPS signals.
1. Card Port
Insert the SD/MMC card into the port.
2. USB port
1. Volume Control
Used to adjust the volume of the headphone
and speaker.
2. Headphone Jack
Used to connect headphones for private
listening. When the headphones are
connected to this jack, the speaker will be
turned off automatically.
3. DC 5V Input Jack
Used to connect to the supplied car adapter.
View of Main Unit

9
Always ensure that the unit and any other external device connected to the unit are
switched off and unplugged from the power supply before you attempt to connect
the unit to any external device.
Connecting to PC
The unit is designed with a USB port which allows you to connect the unit to PC for map
updating. See the below figure for details:
System requirements:
-Windows 98SE, ME, 2000 and XP
(Driver required for Windows 98SE)
-DVD Rom Drive ( for map upgrade purposes)
-Intel Pentium II 233 Mhz
-64 MB RAM
-50 MB available hard drive space
-Available serial port and/or USB Port
-256-color display adapter and monitor
(16 bit color required)
System Connections

10
Inserting SD Card
The unit is designed with SD/MMC Card jack which allows you to insert the SD/MMC
card into the unit as shown below:
Connecting to Headphones
Connect the headphones to the right side of the unit for private listening.
When headphone is connected, the speakers will automatically turn off.
Note: Excessively loud volume could damage your hearing. So turn down the volume
before you connect the headphones, and then raise the volume to comfortable level.
System Connections