Nextar Q3-13 User manual

1
，
POWER SUPPLY:
Connect the supplied adapter to the side of the unit in the slot marked “DC 5V IN.” Plug
the two-prong end of the power cord to an AC100-240V outlet. If you have difficulty
inserting the plug, turn it over and reinsert it. If the unit will not the used for a long time,
disconnect the plug from the outlet.
NOTE:
Before plugging the power cord into an AC outlet, make sure that all the connections
have been made.
CAUTION: These servicing instructions are for use by qualified service personnel only.
To reduce the risk of electric shock, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so.
Refer to service manual for servicing instructions. To reduce the risk of fire or electric
shock, do not expose this apparatus to rain or moisture.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USE-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric to persons.
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
DO NOT EXPOSE THIS APPLIANCE TO RAIN OF MOISTURE.
Important
S
a
f
ety
Instructions

2
NOTES
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with a damp cloth.
7) Do not block any of the ventilation openings. Install in accordance with the
manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized or grounding-type plug. Apolarized plug
has two blades with one wider than the other. A grounding type plug has two blades and
a third grounding prong. The wide blade or the third prong is provided for your safety.
When the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11) Only use attachments/accessories specified by the manufacturer.
12) Use only with a cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip-over.
13) Unplug this apparatus during lightning storms or when unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is damaged,
liquid has been spilled or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
15) Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids,
such as vases, shall be placed on the apparatus.
Important
S
a
f
ety
Instructions

3
Warning
Failure to avoid the following potentially hazardous situations may result in injury or
property damage.
The unit is designed to provide you with route suggestions. It does not reflect road
closures or road conditions, traffic congestion, weather conditions, or other factors that
may affect safety or timing while driving.
Use the unit only as a navigational aid. Do not attempt to use the unit for any purpose
requiring precise measurement of direction, distance, location, or topography. This
product should not be used to determine ground proximity for aircraft navigation.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
The images in this manual are only for reference and they may be
different from the actual ones.
Important
S
a
f
ety
Instructions

4
Navigation Function
Other Special Functions
Navigation Function: The unit is designed to provide you with route suggestions.
It supports voice navigation.
1 GB Flash Storage: Built-in 1G
Flash Storage can store map data. Support file formats: Supports
MP3 and WMA .
Power Adapter Switch: Automatically adapts to voltage requirements in U.S and
other countries.
Features

5
Accessories List
ITEM NAME QTY
Remote Control (with battery) 1
Owner’s Manual 2
Power Adaptor 1
Car Adaptor 1
Mounting Bracket 1
USB Cable 1
Mounting cradle 1
Touch Pen 1
Dashboard mount disk 1
Pouch 1
NOTE
Accessories and their parts numbers are subject to modification without prior notice due
to improvements.
Accessories

6
…………………………………..………..1
……………………………….…………...4
……………………………….…………...5
……………………………….…………...7
……………………………….……….…..9
…………………………….……….…….10
……………………………….…………..12
…………………………….……………..14
……………………………….…………..18
…………………………….……………..20
……………………………………………21
………………………………………..….22
Important Safety Instructions
Features
System Connections
Power Supply Preparation
Troubleshooting
General Setup
Specifications
Accessories
View of Main Unit
Remote Control
Playing Music
Use of the Mount Accessories
Contents

7
Front View
1. MENU button
Press to enter the main menu.
2. Speaker
3. Charge Indicator
When charging the battery, it is red. When the battery is fully charged, it turns
green.
4. POWER button
Press the power button to enter or exit the standby mode.
5. LCD Screen
6. Remote Sensor
Receive signal from remote control for operation.
View of Main Unit

8
Side View
Rear View
1. Build-in GPS Antenna
Receiving GPS signals.
2. External GPS Antenna Jack
Connected to the external
antenna (optional).
3. ON/OFF Switch
Used to switch power on or off.
1. Card Port
Insert the SD card into the port.
2. USB Port
1. Volume Control
Used to adjust the volume of the headphone
and speaker.
2. Headphone Jack
Used to connect headphones for private
listening. When the headphones are
connected to this jack, the speaker will be
turned off automatically.
3. DC 5V Input Jack
Used to connect to the supplied power
adaptor or car adapter.
View of Main Unit

9
1. POWER button
Press to enter or exit standby mode.
2.  direction buttons
Press to select items in the setup
menu.
3.  direction buttons
Press to adjust items in the setup
menu.
4. OK button
Press to confirm selection.
5. MENU button
Press to enter the main setup menu.
6. - button
Press to zoom out the map.
7. MAP button
Press to enter the map view.
8. MUTE button
Press to turn on or off the speaker
output.
9. BACK button
Press to return to the previous
menu.
10. + button
Press to zoom in the map.
Remote Control

10
zAlways ensure that the unit and any other external device connected to the unit are
switched off and unplugged from the power supply before you attempt to connect
the unit to any external device.
Connecting to PC
The unit is designed with a USB port which allows you to connect the unit to PC for map
updating. See the below figure for details:
System requirements:
-Windows 98SE, ME, 2000 and XP
(Driver required for Windows 98SE)
-DVD Rom Drive ( for map upgrade purposes)
-Intel Pentium II 233 Mhz
-64 MB RAM
-50 MB available hard drive space
-Available serial port and/or USB Port
-256-color display adapter and monitor
(16 bit color required)
In the near future map updates will be available for down load from our website. Please
check www.nextar.com periodically for the information on downloads.
System Connections