Nikon COOLPIX 5400 Operating instructions

作成承認印 配布許可印
NIKON CORPORATION
Tokyo, Japan
Recycled paper
再生紙を使用しています
Printed in Japan July 2003
Copyright ｃ 2003 by Nikon Corporation.
All Rights Reserved.
無断転載を禁ず !!
VAA14001
VAA14001-R.3603.A
REPAIR MANUAL

8##4#
- E5400 -
CONTENTS
SPECIFICATIONS ····································································································································· M1-M2
DISASSEMBLY
WARNING ·················································································································································D1
REAR COVER UNIT/FRONT COVER ···································································································D2
DISCHARGE OF MAIN CONDENSER ··································································································D3
LCD UNIT ·················································································································································D3
JOINT UNIT ··············································································································································D5
LENS HOLDER/BATTERY COVER/CF CARD COVER·······································································D6
CF CARD HOLDER··································································································································D6
BATTERY HOLDER/SPEED LIGHT UNIT/PW1 PCB···········································································D7
①Separation from CP1 PCB·····················································································································D7
②ASeparation of the battery holder and speed light unit from PW1 PCB···············································D8
CCD, USB HOLDER·································································································································D8
FINDER UNIT ···········································································································································D9
ASSEMBLY························································································································································A1
FINDER UNIT ···········································································································································A1
CCD/USB HOLDER, LENS/FINDER UNIT····························································································A2
BATTERY HOLDER/SPEED LIGHT UNIT/PW1 PCBA3······································································A3
ԘSet the battery holder and speed light unit onto the PW1 PCB.····························································A3
ԙSetting to the CP1 PCB ························································································································A4
CF CARD HOLDER··································································································································A5
CF CARD HOLDER/BATTERY COVER/LENS HOLDER ····································································A5
JOINT UNT················································································································································A6
LCD UNIT ·················································································································································A6
FRONT COVER ········································································································································A9
REAR COVER·········································································································································A10
PCB ARRANGEMENT···························································································································A11
ADJUSTMENT ·········································································································································· A12-21
CIRCUIT DESCRIPTION···························································································································· E1-E7
CIRCUIT
OVERALL WIRING·································································································································· E8
CCD BLOCK DIAGRAM ························································································································· E9
CAA CIRCUIT DIAGRAM····················································································································· E10
LENS DRIVE BLOCK DIAGRAM ········································································································E11
OVERALL BLOCK DIAGRAM············································································································· E12

8##4#
- E5400 -
DMA CIRCUIT DIAGRAM···················································································································· E13
VF1 CIRCUIT DIAGRAM······················································································································ E14
PW1 CIRCUIT DIAGRAM ····················································································································· E15
SYSTEM BLOCK DIAGRAM················································································································ E16
SYA CIRCUIT DIAGRAM······················································································································ E17
TB1 BLOCK DIAGRAM ························································································································ E18
TB2 BLOCK DIAGRAM ························································································································ E19
TB3 BLOCK DIAGRAM ························································································································ E20
TB4 BLOCK DIAGRAM ························································································································ E21
POWER BLOCK DIAGRAM ················································································································· E22
INSPECTION STANDARDS ······················································································································ R1-R6
TOOL LIST··················································································································································· T1-T2

8##4#
- M1 㨯E5400 -
SPECIFICATIONS
Model Nikon Digital Camera E5400
Effective pixels 5.1 megapixels
Image pixels 1/1.8 type primary-color CCD
Total pixels: 5.26 megapixels
Record pixels pixel࡮ 2592 × 1944 ࡮1280 × 960
࡮2592 × 1728㧔3㧦2㧕࡮1024 × 768
࡮1600 × 1200 ࡮640 × 480
Lens 4-times Zoom Nikkor Lens, f = 5.8~2.4mm (Conversion to 35mm size: 28~116mm),
F2.8~F4.6 (8 groups, 9 lenses)
Electronic zoom Max. 4 times (equivalent to approx. 460mm by conversion to 35mm size)
Automatic focus Contrast detection TTL AF and multi-area auto-focus are possible.
Shooting distance Approx. 50cm before lens ~ ∞, (Approx. 1cm~ ∞in macro mode)
AF area 5 places: When the mode dial is set to P, S, Aor M, 1 place can be selected.
Finder Real image zoom finder, LED display
Magnification 0.26~0.92
Field of view Approx. 80% in up and down, left and right directions
Diopter adjustment 3~1m1
LC monitor 1.5 type high transmission advanced LC, 134000 pixels with luminance/color tone
adjustment
Field of view
(when shooting)
Approx. 97% in up and down, left and right directions (against real object)
Record type
Record media Compact flash card (Type I/II), applied to micro-drive (1GB)
Image file Complying with Design rule for Camera File system (DCF), Exif 2.2 and Digital
Print Order Format (DPOF)
File type Compression: Complying with JPEG-baseline.
FINE (approx. 1/4), NORMAL (approx. 1/8)
BASIC (approx. 1/16)
Non-compression: HI (TIFF)
Animation: QuickTime
Exposure
Metering system 4-mode TTL metering system
࡮256 division multi-metering ࡮Spot metering
࡮Center emphasis metering ࡮AF spot metering
Exposure control Program auto (program shift is possible), shutter prior auto, aperture prior auto,
manual exposure and exposure correction (-2.0~+2.0EV, 1/3EV step) are possible,
and auto-bracketing and AE-BSS are provided

8##4#
- M2 㨯E5400 -
Exposure
Exposure coupling range WIDE side: EV –1.0~+18.0
TELE side: EV+0.5~+18.0
Shutter Mechanical shutter and CCD electronic shutter are used together.
Shutter speed 1~1/4000 sec.*(program auto, auto shooting mode, scene mode), 8~1/4000*
(shutter speed prior auto, aperture prior auto), long-time exposure up to 10
minutes, 8~1/4000*(manual exposure), 1/30~1/8000*in UH continuous shooting
*According to the aperture, the shutter speed at high speed side is limited to
1/2000 sec.
Aperture 6-blade iris diaphragm
Limited steps 10 (1/3 EV step [min. aperture to F8])
Shooting sensitivity Equivalent to ISO50, sensitivity can be changed. (Equivalent to auto, ISO50,
ISO100, ISO200 and ISO400)
Self-timer Approx. 10 seconds and approx. 3 seconds
Built-in speed light
Optical adjustment range Approx. 0.5~4.5m (WIDE side), approx. 0.5~2.8m (TELE side) (When ISO Auto
is set)
Optical adjustment method Automatic optical adjustment control
Accessory shoe Hot shoe contact, with safety lock mechanism
Sync contact Only X contact
Interface USB
Video output NTSC/PAL can be selected.
Input/output terminal ࡮DC input terminal
࡮Audio video (AV) output terminal
࡮Digital terminal (USB)
Power supply ࡮Li-ion rechargeable battery EN-EL1 (accessory), 6V lithium battery 2CR5
(DL245) (sold separately)
࡮AC adapter EH-53 (sold separately)
࡮AC adapter/battery charger EH-21 (sold separately)
Continuous shooting time Approx. 110 minutes (when EN-EL1 is used and LC monitor lights at 20°C)
* Measurement conditions are specified by Nikon. (Zooming at each shooting,
shooting with approx. 30% flash in NORMAL mode)
External dimensions Approx. 108 (W) ×Approx. 73 (H) ×Approx. 69 (D) mm
Weight Approx. 320g (excluding battery and CF card)
Operation environment
Temperature 0 ~ 40°C
Humidity 85% or less (No dew condensation)

8##4#
- D1 㨯E5400 -
DISASSEMBLYޓޓ
Notes:
ԘRemove the CF card and battery prior to disassembly.
ԙDuring disassembly, make a note of the routing of the cords, which screws are
mounted in which parts, etc.
ԚElectrical parts must be grounded since they are easily damaged by static.
ޓNotes for the product in which the lead-free solder is used
• Lead-free solder is used in this product.
• When you perform soldering, special solder and special soldering iron are
necessary.
• Don' mix the lead-free solder with the conventional solder.
• The solder and soldering iron exclusively for this product cannot be used for
others.
WARNING
There are high voltege parts inside. Be careful of this electric shock,
when you remove the cover.
You must discharge the main condenser according to the instruction
of this repair manual before you remove the cover.
!

8##4#
- D2 㨯E5400 -
REAR COVER UNIT/FRONT COVER
• Open the CF card cover.
• Open the DC jacket cover.
• Remove the 3 screws Ԙ(M1.7×4).
• Open the I/O cover.
• Remove the 4 screws ԙ(M1.7×3.5).
• Remove the USB holder and cover.
• Remove the 2 screws Ԛ(M1.7×2.5).
• Separate the rear cover from the camera main unit
slowly.
• Remove the FPC ԛfrom the connector.
• Remove the FPC Ԝfrom the connector.
Front cover
USB cover
USB holder
FPC
FPC
FPA
CF card
cover
DC jack
cover
Connector
Flash holder
Connector
Connector
• Disconnect the connectors ԝand Ԟ.
• Remove the rear cover.
• Remove the FPC ԟ.
• Remove the 3 screws Ԡ(M1.7×4).
• Remove the 2 screws ԡ(M1.7×3.5).
• Remove the screw Ԣ(M1.7×2).
•Remove the screw ԣ(M1.7×2.5).
• Remove the front cover.
• Disconnect the connector Ԥand remove the
flash holder ԥ.

8##4#
- D3 㨯E5400 -
DISCHARGE OF MAIN CONDENSER
WARNING
There are high voltege parts inside. Be careful of this electric shock,
when you remove the cover.
You must discharge the main condenser according to the instruction
of this repair manual before you remove the cover.
!
Main condenser
2KΩ/5W
LCD UNIT
• Remove the screw ①(M1.7×4).
• Remove the 2 screws ②(M1.7×3).
• Remove the screw ③(M1.7×8).
• Remove the screw ④(M1.7×3.5).
• Separate the LCD unit from the rear cover slowly.
• Pull out the connector ⑤from the rear cover.
• The LCD unit can be removed from the rear cover unit.
Connector Ԝ
LCD unit
ԛ
Ԛ
Ԙ
ԙ

VAA14001-R.3603.A
- D4 ･E5400 -
• Turn the LCD unit by 90° in the arrow mark direction.
• Remove the 2 screws ① (M2×3).
• Remove the 2 screws ② (large head).
• Remove the LCD rear cover.
• Disconnect the FPC ① and ②.
• Push in the cords of the connector ③ a little in the arrow
mark "A" direction.
• Disconnect the connector ③.
(Pull out all the cords of the connector ③.)
• Disconnect the connector ④.
• Remove the screw ⑤ (M1.7×3). (Refer to Fig. 1.)
• Remove the joint unit.
• Remove the 2 screws ⑥ (M1.7×2).
Connector ④
②
①
FPC ②
FPC ①
Connector ③
⑥
A
LCD rear cover
Joint unit
⑤
⑤
Fig. 1

8##4#
- D5 㨯E5400 -
Soldering bridge 2
Front LCD cover
LCD unit
LCD holder
LCD side holder Ԙ
VF1 PCB
• Remove the LCD side holder ①.
• The VF1 PCB and LCD unit can be removed.
• When removing the LCD holder from the VF1 PCB, remove the 2 soldering bridges from the VF1 PCB. (Refer
to Fig. 1.)
JOINT UNIT
Joint cover Monitor cover
Joint unit
Joint unit
Ԙ
Ԛ
ԙ
• Float the upper side of the joint cover and then remove it from the joint unit.
• Remove the screw ①(M1.7×2).
• Remove the screw ②(M1.7×4) and then remove the monitor cover.
• Remove the screw ③(M1.7×2.5).
• Remove the TB1 PCB.
Spacer
ԛ
Fig. 1
Screw ԙ

8##4#
- D6 㨯E5400 -
LENS HOLDER/BATTERY COVER/CF CARD COVER
Shaft
CF CARD HOLDER
CF card cover
Shaft ԝ
Connector Ԛ
ԛ
Ԝ
Ԙ
Ԙ
Lens holder
Connector ԙ
CF card holder
Hook
Ԙ
Ԙ
Battery cover
• Remove the 3 screws ①(M1.7×3).
• Disconnect the connectors ②and ③and then remove the lens holder.
• Remove the 2 screws ④(M1.7×2.5) and then remove the TB4 PCB ⑤.
• Remove the shaft ⑥and then remove the battery cover.
• As pushing the CF card cover against the camera main unit, slide it forward and remove it.
• Remove the 2 screws ①(M1.7×4).
• Float the hooks (2 places) and then remove the CF
card holder.

8##4#
- D7 㨯E5400 -
BATTERY HOLDER/SPEED LIGHT UNIT/PW1 PCB
ԘSeparation from CP1 PCB
• Remove the FPC ①.
• Disconnect the connectors ②and ③.
• Float the microphone ④from the PCB. (Refer to Fig. 1.)
• Remove the screw ⑤(M1.7×2.5). (Refer to Fig. 1.)
• Release the hook peg of the holder frame and then separate the battery holder and speed light unit slowly.
• Remove the FPC ⑥. The battery holder and speed light unit can be removed from the CP1 PCB.
FPC Ԙ
FPC Ԙ
Microphone ԛ
CP1 PCB Connector Ԛ
Fig.1
Battery holder Speed light unit
FPC ԝ
Hook peg
position
CP1 PCB
Connector ԙ
Connector Ԛ
Screw Ԝ
Function Phenomena when a fuse has
blown out
PR501 Protection when the DC/DC
converter circuit malfunctions Camera does not operate.
PR502 Protection when the speed
light circuit malfunctions
The speed light condenser
cannot be charged.
PR503 Protection of DC IN detection
circuit
AC adapter detection is not
possible.
Fuse wiring
• Under this condition, 3 fuses can be changed.
PR502
PR501
PR503
PW1 PCB
Ԝ

8##4#
- D8 㨯E5400 -
CCD, USB HOLDER
ԙSeparation of the battery holder and speed light unit from PW1 PCB
• Remove the 4 screws ①(M1.7×4).
• Disconnect the connector ②. The speed light
unit can be removed.
• Disconnect the connector ③. The battery holder
can be removed.
• Take off the spacer ④.
• Remove the screw ⑤(M1.7×3). The PCB TB2
⑥can be removed.
• Remove the 2 screws ⑦(M1.7×2.5). The holder
frame ⑧can be removed.
CP1 PCB
FPC Ԙ
Lens/finder unit
Spacer
Optical filter
Spacer
Ԝ
ԙԛ
Ԛ
Solder ԝ
CP1 PCB
• Remove the FPC Ԙ
• Remove the 2 screws ԙ(M1.7×6).
• Remove the lens/finder unit.
• Spacers and optical filter can be removed.
• Remove the screw Ԛ(M1.7×2.5). The USB holder ԛand USB holder base
Ԝcan be removed.
• Remove the solder ԝfrom the CP1 PCB.
• Remove the CCD Ԟ, mounting lens ԟand spacer Ԡ.
Battery holder
Speed light unit
Connector ԙ
Ԙ
Ԙ
ԟ
Ԙ
Ԟ
Spacer ԛ
PW1 PCB
Connector Ԛ
ԝ
Ԝ
Ԡ
ԟ
Ԟԙ

8##4#
- D9 㨯E5400 -
FINDER UNIT
Finder unit
Ԙ
ԙ
• Take off the FPC ①.
• Remove the 3 screws ②(M1.4×3.5).
• Remove the finder unit.

8##4#
- A1 㨯E5400 -
FINDER UNIT
• Turn the finder cam in the arrow mark direction of Fig. 1
until it contacts with the stopper.
• Return the finder cam by half a turn. Where the distance
is approx. 2mm between the end faces of the V groove
cam and finder cover, stop the finder cam. (Refer to Fig.
2.)
• Fit the gear hole to the pin insertion hole and then insert
the finder positioning pin (J61201).
Finder cover
V groove cam
Gear hole
Pin insertion hole
Fig.1
Fig.2
Note: When setting the finder unit onto the lens unit, be careful
about dust, etc.
• Make sure that the lens unit is in the stowed position.
• Move the lens barrel in the arrow mark direction (left).
Move the finder connection gear in the arrow mark
direction (right).
• Set the finder unit onto the lens unit.
• Attach the 3 screws [1] (M1.4×3.5) .
• Remove the pin.
• Adhere the FPC.
Finder unit
FPC
Ԙ
Lens unit
ASSEMBLY
Approx. 2mm
Tool (J61201)
Finder cam
Moving of finder connection gear
Lens barrel unit

8##4#
- A2 㨯E5400 -
CCD/USB HOLDER, LENS/FINDER UNIT
• Set the spacer Ԙ, mounting lens ԙand CCD Ԛto the CP1 PCB.
• Perform soldering on the CP1 PCB.
• Attach the USB holder base ԛand USB holder Ԝwith the screw ԝ(M1.7 × 2.5). (Tighten the screw
temporarily so that play can remain in the USB holder base ԛ.)
• Set the spacer Ԟ, optical filter ԟand spacer Ԡonto the lens unit.
• Attach the lens/finder unit to the CP1 PCB.
• Attach the 2 screws ԡ(1.7 × 6).
• Connect the FPC Ԣ.
• Contact the rear of the USB holder base ԛwith the mark section of finder and then tighten the screw ԝ
securely.
CP1 PCB
FPC Ԣ
Lens
side
CCD
side
Lens side CP1 PCB
side
Sag side is lens side.
Lens/finder unit
ԡԜ
ԝ
ԡ
Ԛ
Ԟԟ
Ԡ
ԙԘ
ԛ
Solder
Rear side
USB holder
base contact
position

8##4#
- A3 㨯E5400 -
BATTERY HOLDER/SPEED LIGHT UNIT/PW1 PCB
ԘSet the battery holder and speed light unit onto the PW1 PCB.
• Attach the holder frame Ԙwith the 2 screws ԙ(M1.7 × 2.5).
• Attach the TB2 PCB Ԛwith the screw ԛ(M1.7 × 3).
• Adhere the spacer Ԝto the battery holder.
• Set the battery holder to the PW1 PCB.
• Attach the 2 screws ԝ(M1.7 × 4).
• Set the speed light unit onto the PW1 PCB.
• Attach the 2 screws Ԟ(M1.7 × 4).
• Connect the connector ԟ.
• Connect the connector Ԡ.
Cord arrangement
Cord arrangement
Connector ԟ
Ԛ
ԛ
Spacer Ԝ
Battery holder
Speed light unit
Connector Ԡ
PW1 PCB
ԙ
Ԙ
Ԟ
Ԟ
ԝ
ԝ

VAA14001-R.3603.A
- A4 ･E5400 -
② Setting to the CP1 PCB
• Connect the FPC ① to the PW1 PCB and CP1 PCB. (Refer to the gure for the direction of
FPC ①.)
Note: If you connect the FPC ① in the reversed direction, the power supply system will
short-circuit. Be careful.
• Hitch the hook of the holder frame on the CP1 PCB to attach the PW1 PCB.
• Attach the screw ② (M1.7 × 2.5). (Refer to Fig. 1.)
• Insert the microphone ③ into the PW1 PCB. (Refer to Fig. 1.)
• Connect the connector ④.
• Connect the FPC ⑤.
• Fix the tape of microphone’s code. (Refer to Fig. 1.)
FPC ⑤
PW1 PCB
Hook peg
position
Connector ④
②
CP1 PCB
FPC ⑥
Microphone ③
CP1 PCB Connector ④ Fig.1
Screw ②Tape
FPC ①
The side of
the character
The pattern surface is
the reverse.

8##4#
- A5 㨯E5400 -
CF CARD HOLDER
• Set the CF card holder by hitching 2 hooks.
• Attach the 2 screws Ԙ(M1.7 × 4).
CF CARD HOLDER/BATTERY COVER/LENS HOLDER
CF card holder
Hook
Ԙ
Ԙ
CF card cover
Shaft Ԙ
Connector ԛ
ԙ
Ԛ
ԝ
ԝ
Lens holder
Connector Ԝ
• As pushing the CF card cover against the camera main unit, slide it in the arrow mark direction and attach it.
• Attach the battery cover with the shaft Ԙ.
• Attach the TB4 PCB Ԛwith the 2 screws ԙ(M1.7 × 2.5).
• Connect the connectors ԛand Ԝ.
• Set the lens holder and attach the 3 screws ԝ(M1.7 × 3).

8##4#
- A6 㨯E5400 -
JOINT UNT
• Set the TB1 PCB Ԙand attach the screw ԙ(M1.7 × 2.5).
• Set the monitor cover.
• Attach the screw Ԛ(M1.7 × 2).
• Attach the screw ԛ(M1.7 × 4).
• Fit the lower harness side of the joint cover first. (Arrow mark Ԙ)
• Fit the upper side as floating. (Arrow mark ԙ)
LCD UNIT
• Set the spacer Ԙonto the LCD holder.
• Set the spacer ԙand the VF1 PCB onto the LCD holder.
• Move the VF1 PCB in the arrow mark direction and perform soldering bridge (2 places).
• Set the LCD unit onto the LCD holder and then set them onto the front LCD cover.
• Adhere the spacer Ԛonto the socket of the VF1 PCB.
• Fit the LCD side holder to the 2 convex sections of the front LCD cover and set it.
(The even surface of LCD side holder is outside.)
• Attach the 2 screws ԛ(M1.7 2).
Lower harness
Ԙ
ԙ
Joint cover
Screw
ԛ
ԛ
ԙ
Ԙ
Ԛ
Joint unit Monitor cover
ԛ
Front LCD cover
LCD unit
LCD holder
LCD side holder
VF1 PCB
Spacer Ԙ
Spacer ԙ
Spacer Ԛ
Socket
Soldering bridge (2 places)
Move it.
Move it.
Fig.1