Nimbus Water Systems WiMi310 User manual

WiMi310 User Manual v1.0
Wired/Wireless Multi-media interface
WiMi310
User Manual
Ver. 1.0
2017. 1. 16
©2017 NIMBUS INC. All rights reserved. 1/10 www.nimbus.kr

WiMi310 User Manual v.1.0
Document Revision History
Revision Date Description
v1.0 January 16, 2017Initial release of WiMi310 Product Datasheet v1.0
©2017 NIMBUS INC. All rights reserved. 2/10 www.nimbus.kr

WiMi310 User Manual v.1.0
•The RF module limited to OEM installation ONLY.
The OEM integrator is responsible for the compliance to all the rules that apply to the
product in to which this certified RF module is integrated.
•This module must be integrated into a device where the user cannot access the antenna
connector and should not be able to remove or install the module.
Dipole antenna(Under 6.26 ㏈i) can be used with this module. The antenna gain must
not exceed it.
•This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received. Including interference that may cause undesired
operation.
•This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
• This equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
• FCC Caution
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment. This transmitter must
not be co-located or operating in conjunction with any other antenna or transmitter.
• Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
©2017 NIMBUS INC. All rights reserved. 3/10 www.nimbus.kr

WiMi310 User Manual v.1.0
20cm between the radiator & your body.
• This device is intended only for OEM integrators under the following conditions:
The antenna must be installed such that 20 cm is maintained between the antenna and
users, and The transmitter module may not be co-located with any other transmitter or
antenna. As long as 2 conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed.
• IMPORTANT NOTE:
In the event that these conditions cannot be met (for example certain laptop configurations
or colocation with another transmitter), then the FCC authorization is no longer considered
valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM
integrator will be responsible for re-evaluating the end product (including the transmitter)
and obtaining a separate FCC authorization.
• End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be
installed such that 20 cm may be maintained between the antenna and users. The final end
product must be labeled in a visible area with the following:
“Contains FCC ID: ZD7-WIMI310”.
The grantee's FCC ID can be used only when all FCC compliance requirements are met.
• Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding
how toinstall or remove this RF module in the user's manual of the end product which
integrates this module. The end user manual shall include all required regulatory
information/warning as show in this manual.
©2017 NIMBUS INC. All rights reserved. 4/10 www.nimbus.kr

WiMi310 User Manual v.1.0
Purpose of this Document
This document provides simple circuit description and detailed specifications of the
WiMi310™ WiFi Module. The document is intended for Hardware designer wishing to
implementation of WiMi310 module into their own systems.
Related Documents
Additional information related to this document can be found in the Following documents
: PCB Form Factor
PCI Express TM Card Electromechanical Specification Revision 1.1 (March 28, 2005)
©2017 NIMBUS INC. All rights reserved. 5/10 www.nimbus.kr

WiMi310 User Manual v.1.0
Key Features
•2x3 MIMO antenna configuration using two spatial streams
•IEEE Std. 802.11 n Network Standards
•Modulation modes: OFDM
•WPS Certified- Wireless Protected Setup for easy set up and security configuration
•Functions as a legacy endpoint device that conforms to the PCI Express Base Specification,
Rev 1.1
•Optimal channel selection and connection management
•Seamless channel switch under interference
•Only 40 MHz channel bandwidth support.
•300MHz PHY Rate Support and STBC Support for Extended Range
•Antenna: 3x IPex Connectors (2T/3R) - U.FL
•MAC Filtering - No Restriction Mode, White List Mode, Black List Mode; Up to 32
connections
•WDS Enables network management units to collect statistics and manage the device
remotely
•Support Low Power Mode
•RoHS Compliance
©2017 NIMBUS INC. All rights reserved. 6/10 www.nimbus.kr

WiMi310 User Manual v.1.0
Electrical Specifications
Parameter Symbol Value Unit Note
Min. Typ. Max.
Supply Voltage VDD 5.0V-0.3 +6.0 V
Input voltage to digital pins Vin +3.6 V
Storage temperature TSTG -20 +50 ℃
Table 2. Absolute Maximum Ratings
Attention
: Stress above the Max. values listed here may cause permanent damage to the
device. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability. Maximum ratings are absolute ratings : exceeding only one of these value
may cause irreversible damage to the integrated circuit.
The Following Table is defined in typical conditions:Ta=25℃, unless otherwise specified.
Parameter Symbol Value Unit Note/Test Condition
Min. Typ. Max.
Supply Voltage VDD 5.0V3.9 5.0 5.5 V
Input high voltage VIH 2.0 5.5 V
Input low voltage VIL -0.3 0.8 V
Output high voltage VOH 2.4 V without DC load
Output low voltage VOL 0.4 Vwithout DC load
Tri-
State Output leakage
current
IOZ ±10 uA
Pull-up resistor Rpu 26 38 59 KΩ
Pull-down resistor Rpd 33 47 81 KΩ
I/O pins input capacitance CI 4 pF
Total Power Consumption 5.5 W
Table 3. DC Parameters Information
©2017 NIMBUS INC. All rights reserved. 7/10 www.nimbus.kr

WiMi310 User Manual v.1.0
Pinout Description
PIN # Name Type Description
1WAKE# In Link reactivation
45,47,49,51 +5.0V Power +5.0V Power
3,5,8,10,12,14,
16,17,19,20,
45,47,49,51
Reseved Reserve
d
Leave unconnected
4,9,15,18,21,
26,27,29,34,
35,37,40,43,50
GND Power Ground
6,28,48 +1.5V (Reserved) Reserve
d
Not used until now, leave unconnected.
7CLKREQ# Out Reference clock request
11 REFCLKn In Reference Clock, Differential Pair Negative
13 REFCLKp In Reference Clock, Differential Pair Positive
22 PERST# In Functional reset
23 PERn In PCI Express x1 data Input, negative
25 PERp In PCI Express x1 data Input, positive
30 SMB_CLK In SMBus Clock
32 SMB_DATA In/Out SMBus Data
31 PETn Out PCI Express x1 data Output, negative
33 PETp Out PCI Express x1 data Output, positive
36 USB_Dn In/Out USB Serial Data, negative
38 USB_Dp In/Out USB Serial Data, positive
42 LED_WWAN# Out Status Indication LED signal, active low
44 LED_WLAN# Out Status Indication LED signal, active low
46 LED_WPAN# Out Status Indication LED signal, active low
Table 4. Pinout Description
©2017 NIMBUS INC. All rights reserved. 8/10 www.nimbus.kr

WiMi310 User Manual v.1.0
PCI Express Interface Description
•PCI Express Interface Unit(PCIE) functions as a PCI Express legacy endpoint device that
conforms to the PCI Express Base Specification, Rev 1.1.
•As PCIe endpoint device, it can be configured to be either a master initiating PCIe
operation or a target responding to a PCIe operation. The PCIe I/F is a 2.5GHz signaling, x1
differential link
Parameters Description
Master transaction types All memory transactions, except lock
Supports PCIe master DMA
IO and configuration transactions – not supported
Target transaction types Supports two outstanding non-posted requests as a target (computer)
All memory transactions – type 0 only
Message support Supports interrupt and error messages
Configuration space Extended 4KB PCIe Configuration Space
Single function device
Interrupts Support of both MSI and interrupt messages
Error reporting Full support of PCIe baseline error reporting
Full support of advanced error reporting capability
Three error severity levels – correctable, non-fatal and fatal
Header logging and pointer to first uncorrectable error
Programmable error severity
PCI error mapping – mapping errors to PCI error reporting mechanism
Address space Two 32-bit memory BARs
Virtual channels Support of baseline TC0-VC0 mapping
Single VC0 HW resource
Table 5. WiMi310 PCIe Supported Features
©2017 NIMBUS INC. All rights reserved. 9/10 www.nimbus.kr

WiMi310 User Manual v.1.0
Mechanical Description
PCB Form Factors are complied with
“PCI Express Mini Card Electomechanical Specification
Rev.1.2”, (Oct 26, 2007)
•width : 30.0mm
•width : 50.95mm
•Thickness : 5.0mm
©2017 NIMBUS INC. All rights reserved. 10/10 www.nimbus.kr