nologo CARTY-R User manual

CARTY-R
1 2
3 4
All rolling code remote or fix code in the list which can be downloaded in the web site,
excluding the remote controls with the source code, see next paragraph.
5 - Press and release the button to be copied in the remote and wait for a while until the led CARTY-R is
flashing quickly to confirm the correct learning copy process.
6 - While the LED flashes (max 20sec.), press and keep press the corresponding button on CARTY-R
where you need to copy the original code until the LED switched off to confirm the right
learning copy process.
IN THE RADIO RECEIVER
Choose "MODE" in the table: MODE FAST or MODE ENTER or MODE MANUAL
1 - Place the original remote control X in front of CARTY-R at 4 cm of distance
2 - Press and keep pressed button 1 the LED is green
3 - Press four times the button 2 and the led will be red
4 - Release all buttons
Red LED flashes shortly every 2,5 sec.
(8 flashes) for maximum 20sec. which…..
FAAC 433 / 868 GENIUS 433 / 868
The remote control must be a MASTER, if you press the button the LED flashes twice instead fix light.
5 - Press and keep pressed the button to be copied until the Led of CARTY-R lits on.
6 - Release the button and wait.
7 - LED of CARTY-R flashes shortly each 2sec.
This indicate that it is time to memorize the source code.
8 - Press simultaneously buttons 1 and 2 of FAAC or GENIUS remote control and release them
9 - LED of the remote control FAAC or GENIUS flashes (max 9sec.)
10 - Press and keep pressed the button to be copied of FAAC or GENIUS remote control and wait for a
few seconds until the LED CARTY-R flashes quickly.
11 - Press the button which need to be copied and keep pressed
until the LED of CARTY-R switched off.
IN THE RADIO RECEIVER
Check the right function of the new remote control CARTY-R
See MODE FAST or MODE ENTER pressing twice the memorized button.
CLONE THE FIX AND ROLLING CODE WITHOUT THE SOURCE CODE
CLONE THE ROLLING FAAC / GENIUS WITH THE SOURCE CODE
INITIALIZING
 Compatible remote control, code remote control.
 It memorizes four different codes one button each.

V2
5 - Press and keep pressed the corresponding button on original remote control until the LED CARTY-R will lit on
6 - Release the button and wait.
7 - LED of CARTY-R will flash shortly for 2 seconds
This indicate the source code is required
8 - Press simultaneously buttons 1 and 2 of V2 remote control and release them both
9 - LED of CARTY-R will flash quickly
10 - Press and keep pressed the button CARTY-R where you need to memorize the code and wait for a
few seconds until the LED turned off to confirm the correct copy process.
11 - Activate learning process in the receiver
IN THE RADIO RECEIVER
Check if the new CARTY-R is working see V2: MODE FAST
BFT
5 - Press and keep pressed the corresponding button of original remote control until the LED CARTY-R will lit on
6 - Release the button and wait.
7 - After a while LED of CARTY-R then it will flash every 2 seconds.
This indicate that it is necessary to put a source code
8 - Press at the same time buttons 1 and 2 (or push with a pin the hidden button in the back side) of
BFT remote control and release until the LED BFT will turn on.
9 - LED CARTY-R flashes quickly
10 - Press and keep pressed the button CARTY-R where you need to memorize the code and wait for a few
seconds until the LED switched off to confirm that the code has been successfully copied
11 - Activate learning process in the receiver
IN THE RADIO RECEIVER
Check the correct operation of the new CARTY-R see BFT: MODE FAST
TECHNICAL DETAILS
Power supply: battery 3V CR2032
Range up: from 60 to 100 mt.
UE Frequencies: 433,92Mhz / 868,30Mhz
CONFORMITY DECLARATION
Declare under our sole responsibility that the product EB Technology CARTY-R to which this declaration
relates is in conformity with all the essentialrequirements of the European Directive 1999/5/EC (R&TTED)
and the Council
Recommendation 1999/915/EC (Human Exposure). The conformity with the essential requirements of the
above Regulations has been verified against the following harmonised standards:• EN 300 220-2 • EN 301
489-1 • EN 301 489-3 • EN 60950-1:2006 +A11:2009+A1:2010+A12:2011 • EN 50371:2002
GB_CARTY-R 171218_VXX01 www.ebtechnology.it www.nologo.info
!!! If the LED flashes three times and switched off, it means that the code has not been memorized, repeat from step n°2.
!!! The memory CARTY-R is completely rewritable.
!!! To memorize more buttons CARTY-R, repeat the operation from step n°2.
IT REMOTE CONTROL CARTY-R
Scan QR to
download info
about the
CARTY-R
CLONE REMOTE CONTROL ROLLING BFT WITH SOURSE CODE BFT
CLONE REMOTE CONTROL ROLLING V2 WITH SOURSE CODE V2