Northern MONWM2 Service manual

MONWM2
Fully Adjustable
LCD/LED Wall Mount
INSTALLATION & INSTRUCTION MANUAL
Rev.091012
3625 Cincinnati Avenue, Rocklin, CA 95765 ♦ 855-388-7422 ♦ www.northernvideo.com
3625 Cincinnati Avenue, Rocklin, CA 95765 ♦ 855-388-7422 ♦ www.northernvideo.com

2
1
NOTE: Read the entire instruction manual before you start installation and assembly.
Component Checklist
WARNING
• Do not begin the installation until you have read and understood the instructions
and warnings contained in this installation sheet. If you have any questions
regarding any of the instruction or warning, please contact your local distributor.
• This mounting bracket was designed to be installed and utilized ONLY as
specified in this manual. Improper installation of this product may cause damage
or serious injury.
• This product should only be installed by someone of good mechanical ability,
with basic building experiences and fully understanding of this manual.
• Make sure that the supporting surface will safely support the combined load of
the equipment and all attached hardware and components.
• If mounting to wood wall studs, make sure that mounting screws are anchored
into the center of the studs. Use of a stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position
equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can damage the
items, greatly reducing their holding power.
• This product intended for indoor use only. Using this product outdoors could
lead to product failure and personal injury.
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installing. If
any parts are missing or faulty, telephone your local distributor for a replacement.
Package M
Package W
concrete anchor (x3)
W-B
M4x14 (x4)
M-A
M5x14 (x4)
M-B
D4 washer
M-C
(x4)
D (x4)5 washer
M-D
3mm Allen key (x1)
M-E
ST5.5x50 (x3)
W-A

2
1
NOTE: Read the entire instruction manual before you start installation and assembly.
Component Checklist
WARNING
• Do not begin the installation until you have read and understood the instructions
and warnings contained in this installation sheet. If you have any questions
regarding any of the instruction or warning, please contact your local distributor.
• This mounting bracket was designed to be installed and utilized ONLY as
specified in this manual. Improper installation of this product may cause damage
or serious injury.
• This product should only be installed by someone of good mechanical ability,
with basic building experiences and fully understanding of this manual.
• Make sure that the supporting surface will safely support the combined load of
the equipment and all attached hardware and components.
• If mounting to wood wall studs, make sure that mounting screws are anchored
into the center of the studs. Use of a stud finder is highly recommended.
• Always use an assistant or mechanical lifting equipment to safely lift and position
equipment.
• Tighten screws firmly, but do not over tighten. Over tightening can damage the
items, greatly reducing their holding power.
• This product intended for indoor use only. Using this product outdoors could
lead to product failure and personal injury.
IMPORTANT: Ensure that you have received all parts according to the component checklist prior to installing. If
any parts are missing or faulty, telephone your local distributor for a replacement.
Package M
Package W
concrete anchor (x3)
W-B
M4x14 (x4)
M-A
M5x14 (x4)
M-B
D4 washer
M-C
(x4)
D (x4)5 washer
M-D
3mm Allen key (x1)
M-E
ST5.5x50 (x3)
W-A

4
3
2a. Mount on Wood Stud Wall
2b. Mount on Solid Brick and Concrete Block
X X
√
Screw the wall
mount onto
the wall
Screw the wall
mount onto
the wall
X X
√
WARNING
• Make sure that mounting screws are anchored into the center of the studs. Use of a stud finder
is highly recommended.
• Installers are responsible to provide hardware for other types of mounting situations.
• Installer must verify that the supporting surface will safely support the combined load of th e
equipment and all attached hardware and components.
• When installing wall mounts on cinder block, verify the actual concrete thickness is at least
1-3/8" (35mm) for using the concrete anchors. Do not drill into mortar joints! Be sure to
mount in a solid part of the block, generally 1" (25mm) minimum from the side of the block.
It is suggested electric drill on slow setting is used to drill the hole instead of a hammer drill
to avoid breaking out the back of the hole when entering a void or cavity.
• Installer must verify that the supporting surface will safely support the combined load of the
equipment and all attached hardware and components.
WARNING
1. Disassemble the VESA Plate
W-A
W-A
W-B
Drill pilot holes
12
123
Drill pilot holes
Find and mark the exact
location of mounting holes
Mark the exact
location of
mounting
holes
ø 4mm
(ø 5/32")
55mm
(2.2")
50mm
(2")
60mm
(2.4")
50mm
(2”)
ø 8mm
(ø 5/16”)
Loosen

4
3
2a. Mount on Wood Stud Wall
2b. Mount on Solid Brick and Concrete Block
X X
√
Screw the wall
mount onto
the wall
Screw the wall
mount onto
the wall
X X
√
WARNING
• Make sure that mounting screws are anchored into the center of the studs. Use of a stud finder
is highly recommended.
• Installers are responsible to provide hardware for other types of mounting situations.
• Installer must verify that the supporting surface will safely support the combined load of th e
equipment and all attached hardware and components.
• When installing wall mounts on cinder block, verify the actual concrete thickness is at least
1-3/8" (35mm) for using the concrete anchors. Do not drill into mortar joints! Be sure to
mount in a solid part of the block, generally 1" (25mm) minimum from the side of the block.
It is suggested electric drill on slow setting is used to drill the hole instead of a hammer drill
to avoid breaking out the back of the hole when entering a void or cavity.
• Installer must verify that the supporting surface will safely support the combined load of the
equipment and all attached hardware and components.
WARNING
1. Disassemble the VESA Plate
W-A
W-A
W-B
Drill pilot holes
12
123
Drill pilot holes
Find and mark the exact
location of mounting holes
Mark the exact
location of
mounting
holes
ø 4mm
(ø 5/32")
55mm
(2.2")
50mm
(2")
60mm
(2.4")
50mm
(2”)
ø 8mm
(ø 5/16”)
Loosen

6
5
4. Install the Display
TV
TV
TV
Tighten all screws but do not over tighten.
Screw VESA plate onto the display.
3. Install VESA Plate
wall
M-C
M-D
M-A
M-B
Slide the head of VESA plate along VESA plate mount rail until it snug fits into the VESA plate mount.
Then tighten screws(just removed) by hand.
Top of display
wall
Tighten by hand

6
5
4. Install the Display
TV
TV
TV
Tighten all screws but do not over tighten.
Screw VESA plate onto the display.
3. Install VESA Plate
wall
M-C
M-D
M-A
M-B
Slide the head of VESA plate along VESA plate mount rail until it snug fits into the VESA plate mount.
Then tighten screws(just removed) by hand.
Top of display
wall
Tighten by hand

wall
INSTALLATION INSTRUCTIONS
LCD Wall Mount
LDA03-110
23"
MAX
75x75
100x100
ISSUED: JUN 2012
CAUTION: DO NOT EXCEED MAXIMUM
LISTED WEIGHT CAPACITY. SERIOUS
INJURY OR PROPERTY DAMAGE MAY
OCCUR!
5. Adjustment
7
15kg
(33lbs)
MAX
180°
Adjust to desired location or tilt.
Maintenance
• Check that the bracket is secure and safe to use at regular intervals(at least every three months).
• Please contact your dealer if you have any questions.
+20°
-20°
+10° -10°
wall
It is necessary to slightly loosen or tighten
the adjustment screws using a supplied Allen
key according to the different weight of display.
M-E
MONWM2
Fully Adjustable
LCD/LED Wall Mount
INSTALLATION & INSTRUCTION MANUAL
Rev.090412
Tri-ed / Northern Video Distribution ♦3625 Cincinnati Avenue, Rocklin, CA 95765
888-874-3336 ♦www.northernvideo.com

MONWM2
Fully Adjustable
LCD/LED Wall Mount
INSTALLATION & INSTRUCTION MANUAL
Rev.122018
3625 Cincinnati Avenue, Rocklin, CA 95765 ♦ 888-874-3336 ♦ www.northernvideo.com