NOVAWINCH DUO Remote User manual

EN
Product Manual
Dual Function
Wired and Wireless
Winch Remote Control
DUO Remote
Read and understand this manual before product use.

INTRODUCTION
SAFETY PRECAUTIONS
Thank you for purchasing from Novawinch. This remote is
designed to provide a quality winching experience.
The responsibility for safe installation and operation of this
product ultimately rests with you, the operator. Read and
understand all safety precautions and operating instructions
before installing and operating your product. Careless
operation can result in serious injury and/or property
damage.
Please refer to your winch’s operating manual and follow all
safety precautions.
PART IDENTIFICATION
PART LIST
1Handheld Controller
212.8’ (3.9m) Wiring
3Wireless Receiver
4Lanyard, 39” (100cm)
1
2
3 4

DUO Remote Control is compatible with many 12v
NOVAWINCH models, including: PRO, FENIX, T (NVT), K
(NVK), EN and other 12v 4-pin NOVAWINCH Products. If
unsure of compatibility, please contact your dealer or
NOVAWINCH directly.
COMPATIBILITY
CONTROLLER
WIRED OPERATION
• Wired Connection Port
• Wireless Mode Power
Button
• Indicator lights:
• Wired
• Wireless
• Power in
• Power out
Connect DUO handheld controller
to included Wiring by aligning the
4-pin key, push to connect and
tighten the knurled ring for security.
Connect the other end of wiring to the winch solenoid box
and screw on safety ring
Once connected, the remote is active.

WIRELESS OPERATION
1. Press and hold the Wireless Mode Power Button for 3
seconds. This is complete when the Wireless indicator
light is lit.
2. When the Wireless indicator light is active, the remote is
ready.
3. To end wireless mode, press and hold the Wireless Mode
Power Button for 3 seconds until Wireless indicator light
turns off.
4. NOTE: if the DUO Remote is not operated for 2 minutes, it
will turn off automatically to conserve battery power.
Replacing Battery
How to replace DUO battery:
1. Remove ve (5) screws on
back of Handheld remote.
2. Remove back cover to reveal
A23 battery.
3. Replace A23 battery with
new.
4. Replace rear cover, ensuring
rubber seal is aligned and not
pinched. This will maintain
hand controller waterproof
rating.

1. Remove Wireless Receiver if connected. If winch is not
directly connected to winch, provide power to winch.
2. Turn on DUO Handheld Controller by pressing power
button for 3 seconds.
3. Simultaneously press and hold “IN” and “OUT” buttons
4. Green and Red lights will light solidly, ash slowly then
ash quickly.
5. When the indicator lights begin to ash slowly, continue
holding both buttons down and reinstall Wireless
Receiver.
6. Continue holding both buttons down until Indicators
lights turn off. Release buttons and the DUO Handheld
Controller is now paired.
RE-PAIRING DUO REMOTE
PAIRING NEW DUO REMOTE
1. Remove Wireless Receiver if connected. If winch is not
directly connected to winch, provide power to winch.
2. Turn on DUO Handheld Controller by pressing power
button for 3 seconds.
3. Simultaneously press and hold “IN” and “OUT” buttons
4. Green and Red lights will light solidly, then ash slowly.
When the lights begin to ash slowly continue holding
both buttons down and reinstall Wireless Receiver.
5. Continue holding both buttons down until Indicators
lights turn off. Release buttons and the DUO Handheld
Controller is now paired.
Your DUO Remote is paired at the factory. To pair a brand-
new replacement remote to your DUO, follow these steps:

TROUBLESHOOTING
Winch does not respond to
DUO in wired or wireless
mode
Winch is not operational, re-
fer to winch owners manual
If the winch is not
responding to the DUO
commands in Wireless
mode (but does respond in
Wired mode)
Re-Pair DUO controller
Replace DUO battery

Page Intentionally left blank

1689 Xianyuan Road
Jinhua, Zhejiang, China
Tel: [phone]
Fax:[phone]
[email protected]
novawinch.com