Novo Alta altadblsbng User manual

ALTA SIDE BURNER

USER MANUAL

Natural gas & liquid propane congurations

ALTA DOUBLE SIDE BURNER

ALTADBLSBNG / ATLADBLSBLP

ALTA POWER BURNER

ALTAPBNG / ALTAPBLP

NAME:

PART #:

ALTADBLSB

ALTAPB

THANK YOU

Thank you for your purchase. We’d like to welcome you to the NOVO family of luxury outdoor kitchen products and look forward

to being a part of your home for years to come. Welcome to the NOVO family and we hope you love your new Side Burner!

ALTA-SB2

320

638.4

242.5

212.5

597.6

ALTA-PB

400

581.4

550.85

280.68

243.68

10 1/3”

20 5/8”

12 5/8” 22 7/8”

21 3/4”

25 3/8”

7 3/4”

9 5/8”

25 3/8”

11 1/8”

FOR YOUR RECORDS

INSTALLER:

Please record the following information and refer to it when contacting NOVO or an authorized dealer. The serial number is located

on the rating plate. The rating plate is located on the exterior basin of the grill (re box) and on the underneath side of the drip

tray (select models only).

Serial Number:

Model:

Date of Purchase:

Place of Purchase:

Please leave this manual for the owner

TABLE OF CONTENTS

REPLACEMENT PART LIST

EXPLODED VIEW

SAFETY

BEFORE OPERATING

INSTALLATION

GAS REQUIREMENTS

MAINTENCE TIPS

LIGHTING THE SIDE BURNER

LIQUID PROPANE INSTALLATION

WARRANTY

1BUILT-IN SIDE BURNER MANUAL

REPLACEMENT PARTS LIST

S/N Part # PART DESCRIPTION QTY.

LP NG

1ALTA078 HANDLE 1 1

2ALTA079 LID 1 1

3ALTA004 RUBBER STOPPER 8 8

4ALTA080 INNER GRATE 1 1

5ALTA081 OUTER GRATE 1 1

6ALTA082 BURNER LID 1 1

7ALTA083 BURNER UPPER ASSEMBLY 1 1

8ALTA084 MID BURNER ORIFICE 1.5(LP) 1

ALTA085 MID BURNER ORIFICE 2.35(NG) 1

9ALTA086 BURNER BASE 1 1

10 ALTA087 RIGHT ANGLE FITTING 1 1

11 ALTA088 BURNER BASE BRACKET 1 1

12 ALTA089 TUBE BURNER ASSEMBLY 1 1

13 ALTA090 IGNITER PIN 1 1

14 ALTA091 TUBE BURNER IGNITER PIN 1 1

15 ALTA092 TUBE BURNER ORIFICE Φ1.8(LP) 1

ALTA093 TUBE BURNER ORIFICE Φ3.45(NG) 1

16 ALTA094 ORIFICE RIGHT ANGLE FITTING

ASSEMBLY 1 1

17 ALTA095 LED LIGHT WIRE 1 1

18 ALTA036 LED LIGHT 2 2

19 ALTA096 CONTROL PANEL 1 1

20 ALTA040 KNOB BEZEL 2 2

21 ALTA042 KNOB 2 2

22 ALTA097 DRIP TRAY 1 1

23 ALTA098 IGNITE WIRE L=240MM 1 1

24 ALTA099 IGNITE WIRE L=330MM 1 1

25 ALTA100 SS RIPLE TUBE L=325MM Φ9MM 2 2

26 ALTA045 LED LIGHT SWITCH 1 1

27 ALTA101 LED POWER SOURCE WIRE 1 1

28 ALTA076 TRANSFORMER 1 1

29 ALTA102 VALVE 2 2

30 ALTA103 MANIFOLD 1 1

31 ALTA049 VALVE LATCH 2 2

32 ALTA104 REGULATOR zRV48 1 1

33 ALTA105 1/2” IN & OUT BRUSHED ELBOW 2 2

ALTA POWER BURNER

BUILT-IN SIDE BURNER MANUAL

REPLACEMENT PARTS LIST

S/N Part # PART DESCRIPTION QTY.

LP NG

1ALTA057 HANDLE 1 1

2ALTA058 LID 1 1

3ALTA059 GRATE 1 1

4ALTA060 IGNITER PIN ASSEMBLY 2 2

5ALTA061 BURNER ASSEMBLY 2 2

6ALTA062 ORIFICE (LP 1.05) 2

ALTA063 ORIFICE (NG 1.6) 2

7ALTA064 BURNER BASE ASSEMBLY 2 2

8ALTA065 VALVE 2 2

9ALTA066 MANIFOLD 1 1

10 ALTA067 REGULATOR FITTING 1 1

11 ALTA049 VALVE LATCH 2 2

12 ALTA068 DRIP TRAY 1 1

13 ALTA069 IGNITER WIRE 330MM 1 1

14 ALTA070 IGNITER WIRE 480MM 1 1

15 ALTA071 RIPPLE TUBE 420MM 1 1

16 ALTA072 RIPPLE TUBE 200MM 1 1

17 ALTA073 LED LIGHT WIRE 1 1

18 ALTA036 LED LIGHT 2 2

19 ALTA074 CONTROL PANEL 1 1

20 ALTA040 KNOB BEZEL 2 2

21 ALTA042 KNOB 2 2

22 ALTA075 LED POWER SOURCE WIRE 1 1

23 ALTA076 LED LIGHT SWITCH 1 1

24 ALTA077 TRANSFORMER 1 1

ALTA DOUBLE SIDE BURNER

3BUILT-IN SIDE BURNER MANUAL

EXPLODED VIEW

26 27

23 24 25

28 29

ALTAPB大功率分解图

32 33

ALTA POWER BURNER

BUILT-IN SIDE BURNER MANUAL

EXPLODED VIEW

ALTASB2双边炉分解图

ALTA DOUBLE SIDE BURNER

5BUILT-IN SIDE BURNER MANUAL

1. Shut o the gas to the appliance.

2. Extinguish any open ame.

3. Open lid to vent.

4. If odor continues, keep away from the appliance,

and immediately call your gas supplier or re

department.

IF YOU SMELL GAS

WARNING!

FAILURE TO READ AND FOLLOW THE “USE

AND CARE” INSTRUCTIONS COULD RESULT

IN A FIRE OR EXPLOSION THAT COULD

CAUSE SERIOUS BODILY INJURY, DEATH

OR PROPERTY DAMAGE.

WARNING!

1. Do not store or use gasoline or other ammable

vapors and liquids in the vicinity of this or any other

appliance.

2. A propane cylinder not connected for use shall

not be stored in the vicinity of this or any other

appliance with ame.

WARNING!

Refer to this manual for assistance or for additional

information consult a qualied professional installer,

service agency or gas supplier.

WARNING!

IMPORTANT:

READ THESE INSTRUCTIONS CAREFULLY

BEFORE STARTING INSTALLATION

This Side Burner must be installed in accordance with local

codes and ordinances, or, in the absence of local codes, with

either the latest National Fuel Gas Code (ANSI Z223.1/ NFPA

54), and Natural Gas and Propane Storage and Handling

Installation Code (CSA-B149.1).

If stored indoors, detach and leave any fuel cylinders outdoors.

The burning of gas cooking fuel generates some by-products,

which are on the list of substances, which are known by the State

of California to cause cancer or reproductive harm. California

law requires businesses to warn customers of potential exposure

to such substances. To minimize exposure to these substances,

always operate the unit according to the use and care manual,

ensuring you provide good ventilation when cooking.

Always have your Side Burner vented correctly, installed

by a professional and inspected by the local city building

department.

CODE AND SUPPLY REQUIREMENTS:

FOR OUTDOOR USE ONLY

CALIFORNIA PROPOSITION 65 WARNING

SAFETY AND INSTALLATION INSTRUCTIONS

Disconnect all propane or natural gas supplies

to this unit before servicing.

FLAMMABLE GAS

WARNING!

BUILT-IN SIDE BURNER MANUAL

GENERAL SAFETY REQUIREMENTS

SAFETY AND INSTALLATION WARNINGS

• Have an ABC Fire Extinguisher readily accessible. Never attempt to extinguish a grease re with water or other liquids.

• Keep electrical supply cords and fuel supply hoses away from heated surfaces.

• Do not heat unopened food containers as they may explode.

• Never store additional or empty fuel cylinders in the side burner cabinet or near the side burner. Do not store cylinders indoors

or on their sides. Never use dented, rusty or damaged cylinders.

• Close supervision is necessary when this or any appliance is used near children. Keep children away from the Side Burner

during operation and until the Side Burner has cooled o.

• Do not use aluminum foil to cover cooking grates. This will alter combustion airow and trap excessive heat in the control area

leading to damaged knobs or igniter modules.

• After the Side Burner is installed by a professional technician be sure they show you where your gas supply shut-o valve

is located. All gas lines must have a shut-o that is easily accessible. If you ever smell gas, check for leaks IMMEDIATELY.

Never check for gas leaks with an open ame.

• Never operate Side Burner in a windy area. If windy conditions exist, install a suitable windbreak.

• Damage caused by leaving operating burner unattended is not covered under the terms and conditions of the NOVO

Warranty. Never leave open ame unattended.

• Never use Side Burner without drip pan in place. Make sure drip pan is properly and fully inserted. Failure to do so may allow

hot grease or boil-overs to become a re or explosion hazard.

• Do not repair or replace any part of the Side Burner unless specically recommended by this manual. A qualied technician

should perform all other necessary service.

• The Side Burner is not designed/certied for and cannot be installed in or on recreational vehicles, portable trailers, boats or

any other mobile vehicle.

• Children should never be left alone or unattended in an area where a Side Burner is located. Install your side burner well

away from areas where children play. Do not store items that may draw the interest of children in or around the side burner,

island or masonry enclosure. When in use and immediately after, areas of the Side Burner are hot enough to

cause severe burns!

• Avoid wearing loose-tting, long sleeves or ammable garments when using the side burner. Never touch cooking grates on

top or surrounding metal surfaces with your bare hands as these areas become extremely hot during use and could cause

severe burns. Use an insulated glove or mitt when attempting to handle parts of the Side Burner.

• Never lean over or look directly over the cooking surface when attempting to light.

• The Side Burner lid must be completely removed before lighting and during operation.

• Do not cover the Side Burner with the lid until the cooking surface has cooled down.

• Never connect any unregulated gas supply to the Side Burner. Supplied regulator must be used in order to validate warranty.

WARNING!

7BUILT-IN SIDE BURNER MANUAL

BEFORE OPERATING

SHIPMENT ARRIVING DAMAGED:

IMPORTANT NOTES:

VISIBLE DAMAGE

If your shipment arrives with visible damage to the box/carton,

be sure the damage is noted on the bill of freight or express

receipt and signed by the person making the delivery. File claim

for damages immediately, regardless of the extent of damage.

BE MINDFUL OF WIND DIRECTION

When selecting a suitable location, consider important factors

such as exposure to the wind and foot trac patterns. Position

your Side Burner so the prevailing wind blows into the front

control panel (at your back when operating), allowing for

proper front to rear airow. Side Burners located in areas with

prevailing winds should be protected by a wind barrier, wind

deector, or wind guard. The Side Burner is designed to pull

in air from the front and exhaust through the rear of the unit.

Winds hitting the back of the Side Burner directly may cause

problems.

CONCEALED DAMAGES

If damages are unnoticed until the Side Burner is unpacked,

notify the transportation company or carrier immediately and

le a concealed damage claim with them. This should be done

within (5) days of the delivery date. Be sure to hold on to the

box/carton for inspection. We cannot assume responsibility for

damage or loss incurred in transit.

GAS LINE LENGTH

Keep all gas supply lines as short as possible. Gas lines lose

pressure over distance and with each elbow or “t” tting added.

This drop in pressure aects Side Burner performance.

PROPER LEVELING

PROPER LEVELING DURING INSTALLATION IS CRITICAL.

A SIDE BURNER THAT IS OUT OF LEVEL WILL CAUSE

ERRATIC BURNER COMBUSTION AND INEFFICIENT,

UNEVEN HEATING. THE SIDE BURNER SHOULD BE

LEVEL IN ALL DIRECTIONS. ADJUSTMENTS MAY

NEED TO BE MADE EACH TIME WHEN MOVING A

FREESTANDING UNIT.

CONSTRUCTION ZONES

Keep all stainless steel products away from construction zones.

Construction debris such as (but not limited to) stone dust,

stucco, and lime dust could damage or permanently discolor

stainless steel products. Keep all caustic chemicals including

chlorine and pool cleaning products away from stainless steel

at all times.

IMPORTANT: THIS SIDE BURNER IS FOR

OUTDOORS USE ONLY.

The Side Burner must be installed in masonry or other

type of reproof surround. The unit is not insulated and

therefore must be installed or placed with 16” – 18” of

side and back clearance from unprotected combustible

materials such as wood, plastic, or stucco with wood

framing. PLEASE NOTE: if this is not done, the

combustible material will catch on re and potentially

damage your house structure and may cause bodily

harm due to the re.

WARNING!

Do not install this unit under unprotected ammable

surfaces. Do not install or use this

appliance inside a building, garage, or any other

enclosed area. It must not be used in

or on recreational vehicles or boats.

This is a slide-in unit designed to t into open-front

enclosures. The control panel of the unit is

removable for gas hookup, servicing and burner

adjustment. The control panel must remain removable

after you install the unit. Do not have this panel sealed

for any reason.

Important: The lip on the side requires 1” ( 2.5 cm) of

countertop on each side and back to support the unit.

Note: We recommend you build the enclosure for the Side

Burner 6”-12” (15.2 cm- 30.5 cm)

LOWER than your countertop. This will ensure a safer

environment when using tall cooking

pots like the turkey fryer, which can hold 40lbs of hot

ammable oil. Please make sure that

you do not overll large pots of oil for the oil will spill over

and catch on re.

Note: This unit should be installed so that it can be

removed at a later date if factory service is required.

BUILT-IN SIDE BURNER MANUAL

BEFORE OPERATING / INSTALLATION

ENSURING PROPER COMBUSTION AIR AND

COOLING AIR FLOW

EXHAUST REMOVAL Do not store or use gasoline or other ammable liquids

or vapors near this or any other appliance.

Do not store spare LP cylinders under or near this

appliance.

Never ll cylinder more than 80% capacity.

If these instructions are not followed, re causing

serious injury or even death may occur.

For installation in non-combustible locations only.

Do not locate under unprotected, overhead

combustible surfaces.

If installed under a patio roof, the cooking grid area should be

fully covered by a chimney and exhaust hood. An exhaust fan

with a rating of up to 1,000 CFM (472 liters per second) may

be necessary to eciently remove smoke and other cooking

by-products from the covered area. Installation in fully enclosed

patio areas is not recommended.

Disconnect all power supplies before servicing.

You must maintain proper air ow for your Side Burner to

perform as it was designed. If airow is blocked, overheating

and poor combustion will result. Make sure not to block the 1”

(2.5 cm) front air inlet along the bottom of the control panel

or more than 75% of the support grid surface with pans or

griddles.

Note: The 1” (2.5 cm) front air space allows access to the drip

tray.

CUTOUT DIMENSIONS

ELECTRICAL PARTS AND COMPONENTS

WARNING!

Disconnect all propane or natural gas supplies to this unit

before servicing.

FLAMMABLE GAS

WARNING!

MINIMUM PRESSURE REQUIREMENTS

Ensure the gas supplied meets the minimum pressure

requirements. See below table for gas requirements measured

in water column (w.c.) pressure:

Gas Type Maximum Minimum

Natural Gas 7” w.c. 4” w.c.

Liquid Propane 14” w.c. 11” w.c.

Dimensions Width Depth Height

ALTADBLSB 10 3/4 20 3/4 8

ALTAPB 13 3/4 23 8

Both the regulator and burner orices have been tuned for

the type of gas specied on the rating plate. Converting to a

dierent type of gas requires a conversion kit. Conversion kits

are included with this Side Burner and located with the manual.

Converting gases may require additional parts not included

with this Side Burner. (See Gas Conversion section for details).

Each appliance is set and tested at the factory for the type of

gas supply to be used. Identify the

type of gas, either natural gas or LP (Liquid Propane) gas and

make sure that the marking on the rating plate located on the

side of the unit matches the gas being supplied to the Side

Burner. The rating plate is located on the side of the Side Burner.

All gas hook up connections should be made by a qualied

technician and in accordance with local codes and ordinances.

The installation must conform with local codes or, in the

absence of local codes, with either the national Fuel Gas Code,

ANSI Z223.1/NFPA 54, or CAN/CGA-B149.1, Natural Gas

Installation Code or CAN/CGA-B149.2, Propane Installation

Code.

GAS SAFETY REQUIREMENTS

9BUILT-IN SIDE BURNER MANUAL

If your Side Burner is factory built for L.P., the regulator required

is set for 10” water column and is for use with L.P. gas only. If

unit is NOT supplied with regulator please make sure that all

requirements are met for the type of regulator required.

It must be provided with a shut-o valve terminating in gas

tank valve outlet. It must include a collar to protect the cylinder

valve. The cylinder supply system must be arranged for vapor

withdrawal.

A typical LP gas installation is show on the right. Make sure

that the factory supplied regulator is used and installed with the

arrow mark on the regulator pointing towards the Side Burner.

Do not use any replacement regulator other than that specied

by the manufacturer. Use only pipe sealants that are approved

for use with natural and LP gases. An installer-supplied

gas shuto valve must be installed in an accessible location.

(Reference: leak test procedure).

An enclosure or island for an LP gas cylinder must be vented

on the level of the cylinder valve and at oor level. The

eectiveness of the opening(s) for purposes of ventilation shall

be determined with the LP gas supply cylinder in place. This

shall be accomplished by one of the following:

a. One side of the enclosure shall be fully open; or

b. For an enclosure having four sides, a top and a bottom, at

least two ventilation openings at cylinder valve level shall be

provided in the sidewall, equally sized, spaced at 180 degrees

(3.14 r), and unobstructed. Each opening shall have a total free

area of not less than 1/2 square inch per pound (7.1 cm2/kg) of

stored fuel capacity and not less than a total free area of 10

square inches (64.5 cm2).

Ventilation opening(s) shall be provided at oor level and

shall have a total free area of not less than ½” square inch per

pound (7.1 cm2/kg) of stored fuel capacity and not less than

a total free area of 10 square inches (64.5 cm2). If ventilation

openings at oor level are in a sidewall, there shall be at least

two openings. The bottom of the openings shall be at oor level

and the upper edge no more than 5 inches (127 mm) above

the oor. The openings shall be equally sized, spaced at 180

degrees (3.14 r) and unobstructed.

Although LP Gas Cylinders may be used, it is not

recommended due to the large amount of Gas

Consumption and may freeze up the gas cylinder as

well as a safety risk.

The LP-gas supply cylinder must be constructed and marked

in accordance with the specications for LP-gas cylinders of the

U.S. Department of Transportation (D.O.T.) or the National

Standards of Canada CAN/CSA-B339, Cylinders, Spheres

and Tubes for the Transportation of Dangerous Goods, and

Commission, as applicable; and

1. Provided with a listed overlling prevention device.

2. Provided with a cylinder connection device compatible

with the connection for outdoor cooking appliances.

GAS REQUIREMENTS

CHECK TO ENSURE THAT THE GAS SUPPLY

HOSE DOES NOT COME IN CONTACT WITH

ANY HOT SURFACE OF THE SIDE BURNER.

WARNING!

L.P. GAS (LIQUIFIED PETROLEUM /PROPANE)

LP GAS HOOK-UP

VENTING YOUR ENCLOSURE:

L.P. GAS SAFETY REQUIREMENT

1. This gas appliance and its individual shuto valve must

be disconnected from the gas supply piping system

during any pressure testing of that system at the test

pressures in excess of ½ psi (3.5 kPa).

2. This appliance must be isolated from the gas supply

piping system by closing its individual manual shuto

valve during any pressure testing of the as supply piping

system at test pressures equal to or less than 1/2 psi (3.5

kPa). If the gas Side Burner is factory built for natural

gas, the regulator supplied is set for 4” water column.

The regulator is convertible Later to 10” water column

for system LP application. Do not use with a 20-lb LP

cylinder.

NATURAL GAS INSTALLATION

The installation must conform with local codes or, in the

absence of local codes, with either The National Fuel Gas

Code, ANSI Z223.1/NFPA 54, or CAN/CGA-B149.1, Natural

Gas Installation Code or CAN/CGA-B149.2, Propane

Installation Code.

Do not operate the gas Side Burner indoors or in any enclosed

area. If the gas Side Burner is not in use, the gas must be

turned o at the supply cylinder. If the Side Burner is to be

stored indoors, disconnect the gas supply cylinder and leave the

cylinder outdoors.

BUILT-IN SIDE BURNER MANUAL

CAUTION BEFORE TESTING

Make sure that the regulator is set for natural gas. To check,

remove the top cap. You will nd the conversion plastic pin

attached to the cap to the underside of the cap. If the disc (1/2

in. diameter) of the pin is close to the cap, then the regulator is

set for natural gas. If the disc is at the tip of the pin, away from

the brass cap, the regulator is set for system LP application. To

convert to natural gas, remove the plastic conversion pin and

invert and replace it back in a manner such that the disc is close

to the brass cap. For both natural and LP, the maximum inlet

pressure is 14” water column.

Make sure that the factory-supplied regulator is used and

installed with the arrow mark on the regulator pointing towards

the gas Side Burner. Do not use any replacement regulator

other than that specied by NOVO. Use only pipe sealants

that are approved for use with natural and LP gases. An

installer-supplied gas shuto valve must be installed in an

accessible location.

GAS REQUIREMENTS

Finding and/or xing a gas leak is NOT a

“DO-IT-YOURSELF” procedure.

1. Shut o gas to the appliance right

away.

2. Extinguish any open ame.

3. Make sure the cover is not placed over

the burner.

4. If gas smell continues, keep away from

the appliance and immediately call gas

supplier or re department.

IF YOU SMELL GAS

WARNING!

LEAK TEST

NEVER USE THE SIDE BURNER WITHOUT FIRST

LEAK TESTING THE GAS CONNECTIONS.

WARNING: DO NOT USE OPEN FLAME TO CHECK

FOR LEAKS. USE OF AN OPEN FLAME COULD

RESULT IN A FIRE, EXPLOSION AND BODILY

HARM.

DO NOT SMOKE WHILE PERFORMING THE LEAK

TEST!

IF AT ANYTIME YOU SMELL GAS – SWITCH

OFF ALL OF YOUR EQUIPMENT AND CALL A

PROFESSIONAL TO DETECT THE GAS LEAK.

ALWAYS INFORM ALL MEMBERS OF YOUR

FAMILY ABOUT THIS IMPORTANT FACT – SMELL

GAS = DO NOT USE THE EQUIPMENT.

To prevent re or explosion hazard, DO NOT use or permit

sources of ignition in the area while performing a leak test.

Perform leak test outdoors only. Check to ensure that exible

hoses do not have any cuts and wear that may aect the

safety before each use. Only the factory supplied regulator

must be used. Use only replacement regulator specied by the

manufacturer.

A minimum of 1” clearance to the sides of the Side

Burner above cooking surface to non-combustible construction

is recommended.

A minimum clearance of 1” from the back of the Side

Burner above cooking surface to non- combustible construction

is required.

1. Prepare a leak testing solution of soap and water in a

spray bottle (50% solution)

2. Conrm that all control knobs are in the o position

3. Turn the main gas supply valve ON

4. Apply the leak test solution by spraying on all of the pipe

joints, ttings and hose

5. A gas Leak is detected when:

• There is a faint smell of gas and/or

• There are bubbles around the connections.

6. DO NOT ATTEMPT TO IGNITE THE BURNER

7. Turn o the main Gas Supply

8. Call a certied/qualied professional to repair the GAS

LEAK

9. DO NOT attempt to use the Side Burner until the leak

is xed.

11 BUILT-IN SIDE BURNER MANUAL

NOTE:

Its is recommended to build the Side Burner at least 6”-12” lower

than the counter-top.

GAS REQUIREMENTS / MAINTENANCE

Spiders and other insects can nest in the burner of this and

any other Side Burner, which causes the gas to ow from the

front of the burner. This dangerous “condition” can cause a re

behind the valve panel, damaging the Side Burner and making

the Side Burner unsafe to operate. Inspect the burners once a

year or if the Side Burner has not been used for more than one

month or if any of the following conditions occur:

1. The smell of gas in conjunction with the burner ames

appearing yellow.

2. The Side Burner does not reach temperature.

3. The Side Burner heats unevenly.

4. The Side Burner makes popping noises.

SPIDER AND INSECT WARNING

STAINLESS STEEL MAINTENANCE

SIDE BURNER GRATE MAINTENANCE

The Side Burner is made of stainless steel construction. It is

non-rusting. Never clean the stainless steel when it is hot. After

the initial cooking use, certain areas of the Side Burner may

discolor. This is a normal discoloration caused by the internal

heat given o by the burner. Specks of grease can gather

on the surface of the stainless steel and get baked-on. These

can be removed by using a mild abrasive pad (like Scotch

Brite) with a stainless steel cleaner. Use the mildest cleaner and

always scrub in the direction of the grain.

Do not use steel wool to clean the Side Burner.

Do not use abrasives on the polished highlights. Be extra

careful when cleaning around the highlights. Metal polisher

or mild chrome cleaner can be used to bring back the luster

on highlights. To touch-up minor scratches in the stainless steel,

The easiest way to clean the grates is to scrub them with a

barbecue brush immediately after cooking is completed and

the ame is turned o.

Wear a heat protective barbecue mitt to protect your hands

from the heat and steam. Dip a brass bristle barbecue brush in

tap water and scrub the hot grates. Dip the brush frequently in

tap water. Steam, created as water comes in contact with the

hot Side Burner, helps loosen food particles stuck in the Side

Burner. These food particles will either get burned or fall into

the cleaning pan. Cleaning of the Side Burner would be longer

and more dicult if the Side Burner grates are allowed to cool

before cleaning.

sand the aected surface very lightly, with 100-dry grit emery

sandpaper in the direction of the grain.

BURNER CLEANING & MAINTENANCE

OPERATING INSTRUCTIONS

BEFORE LIGHTING THE SIDE BURNER

Burners are made of heavy gauge brass and can be cleaned

using a bristle brush, warm water and soap. Check every

porthole for clogs. Use a wire pin to clean out clogged ports.

Make sure the burner is dry before installing it back to the Side

Burner.

The drip pan collects grease, liquid and fallen food particles.

Allow the pan and its contents to cool before cleaning. Slide

the pan out and wipe it clean. Make sure the drip pan is fully

inserted back into the Side Burner. It is highly recommended to

clean the pan after every use to avoid any possibility of a grease

re. DO NOT use the Side Burner without the drip pan pushed

all the way to the back of the Side Burner unit.

1) DO NOT ATTEMPT TO LIGHT THE SIDE BURNER

IF YOU SMELL GAS.

2) WARNING! IT IS CRITICAL THAT THE GAS

BURNERS ARE PROPERLY INSTALLED WITH THEIR

ORIFICES INSIDE THE BURNERS AIR SHUTTERS.

If not properly installed, gas may leak outside of the

burner that could lead to re, potential damage to

your Side Burner and bodily injury.

BUILT-IN SIDE BURNER MANUAL

LIGHTING YOUR SIDE BURNER

Inspect the gas supply piping or hose prior to turning the gas

ON. If there is evidence of cuts, wear, or abrasion, it must be

replaced prior to use. The replacement pressure regulator and

hose assembly must be the type specied by the manufacturer.

Do not use the Side Burner if the odor of gas is present. The

pressure regulator and hose assembly supplied with the units

must be used. If the unit is LP, screw the regulator and hand

tighten to the valve of the cylinder and leak check the hose and

regulator connections with a soap and water solution before

operating the Side Burner. Make sure you always read about

LEAK PREVENTION. Always keep your face and body as

far away as possible when lighting. Refer to spiders and insects

warning and procedure under the cleaning and maintenance

page of this manual.

ASSEMBLY & LIGHTING

Remove all packing materials.

Ensure that the burners are positioned securely on their orices.

Place grates in the proper location over burners.

Connect gas using proper gas regulator.

FOR OUTDOOR USE ONLY!

1. Open the gas supply shut-o valve.

2. Push in the knob to the left wait a few seconds and then

click the ame-thrower ignition system to ignite. If the

igniter does not light turn to the right and OFF position,

verify that the gas is on and then try again.

3. Once you see or hear a ame you can adjust the burner

to the desired position.

CAUTION: If ignition does not take place within a few clicks,

turn knob to the OFF position, wait for ve minutes and repeat

step 2.

Match/BBQ Lighter Lighting Instructions:

The burners can be lit manually using a lighted long match or

long BBQ lighter.

1. Push and turn the knob counter-clock-wise past the

“CLICK” position. Hold the knob pushed in for 5 seconds.

2. Insert a lit match or BBQ lighter through the grates

and near the top of the burner. Once you see or hear a

ame you can release the knob.

NOTE

Improper lighting procedures can cause the flow

control to activate, resulting in reduced heat

output. If this is suspected, shut off all burner

controls and cylinder valve. Wait 30 seconds,

then very slowly re-open cylinder valve. Wait an

additional 5 seconds before turning burner control

knob and attempting to light.

ALWAYS WAIT 5 MINUTES BEFORE

RE-LIGHTING A HOT BURNER!

Important: If burner fails to light within 5 seconds, turn o gas

and wait 5 minutes before repeating the process.

Warning: If you smell gas, shuto the gas supplies and

immediately checks for leaks using the soapy water technique.

CONNECTING TO THE LP TANK

The hose and regulator are connected in the following manner:

• Insert the regulator inlet into the cylinder valve and turn

the black coupling nut clockwise until the coupling nut

is hand tight. DO NOT over-tighten this connection.

• To disconnect the coupling nut, rst make sure the

main cylinder valve is turned o. Grasp the coupling

nut and turn counter clockwise. The inlet will then

disengage.

FILLING AND REFILLING LP GAS CYLINDERS

All purging and relling of LP gas cylinders must

be performed by qualied personnel in the LP gas

industry. Never store a spare LP gas cylinder under or

near this appliance.

Never ll the LP gas cylinder beyond 80 percent

full. Failure to follow these instructions may result in

explosion, personal injury or death.

13 BUILT-IN SIDE BURNER MANUAL

LIQUID PROPANE INSTALLATION

LP gas grill models are designed for use with a standard 20 lb.

liquid propane gas (LP) tank with type (1) valve connections.

(Not included)

Never connect your gas grill to an LP tank that exceeds this

capacity. A tank of approximately 12 inches in diameter by

18-1/2 inches high is the maximum size LP gas tank to use. A

propane tank with an OPD (Overll Prevention Device) must

be used. This safety feature prevents the tank from being over-

lled which can cause malfunction of the LP gas tank, regulator

and/or grill.

The LP cylinder must be constructed and marked in

accordance with the specications for LP gas cylinders of the

U.S. Department of Transportation (DOT) and designed for

use with a Type 1 system only. Be sure to read and follow all LP

connection instructions.

A dented or rusty LP cylinder may be hazardous and should

be avoided. If in doubt, have it checked by your LP supplier.

Always check for leaks after every LP cylinder change. (See

Checking For Leaks)

Cylinders must be stored outdoors in a well-ventilated area out

of the reach of children. If your grill is stored indoors, the LP

cylinder must be stored outside, in upright position and away

from excessive heat.

CONNECTING TO A SIDE BURNER

You will need a ‘T’ adapter tting (not provided) or similar

connection to connect a single gas line to both a side burner

and a grill. We recommend a licensed gas technician install

all gas lines. See below gure for installation of a ‘T’ adapter.

IMPORTANT

All installation and all installation parts must conform

to local codes with the National Electrical Code, ANSI

Z223.1/ NFPA 70 latest edition and the National Fuel

Gas Code ANSI Z223.1/NFPA 54 in the U.S. and

CGA-B149.1/.2 in Canada

LIQUID PROPANE INSTALLATION

NOTE: Ventilation is required in the enclosure on opposite

sides to create cross-ventilation. Liquid propane is heavier than

natural gas and vents should be located near the bottom of

the enclosure.

Before lighting the burners, inspect the gas supply piping

or hose. If there is evidence of cuts, wear, or abrasion, it

must be replaced prior to use. Always keep your face

and body as far away from the grill as possible when

lighting.

WARNING!

BUILT-IN SIDE BURNER MANUAL

NOVO WARRANTY

GAS APPLIANCES (GRILLS, SIDE/

POWER BURNERS)

• Limited Lifetime Warranty on

construction and manufacturer defects

• Limited Lifetime Warranty on stainless

steel construction

• Limited Lifetime Warranty on cooking

grates, burners, burner covers, valves,

stainless steel burner covers and heat

zone separators, temperature gauges, &

hood springs

• Limited Lifetime Warranty on briquette

systems

• 3 Year Warranty on all other parts,

components, & electrical, including: LED

bulbs, wire harness, & switches; power

source wire; transformer; interior halogen

light wire & bulb; regulators

REFRIGERATION (15” & 24” models)

• 3 Year Warranty on all construction

including compressors

• 1 Year Warranty on transformer, LED bulbs,

LED harness, power source wire, LED

switches, interior halogen light wire/bulbs

NOVO products include our LIMITED LIFETIME WARRANTY with all replacement parts 100% non-prorated.

NOVO Limited Warranty is valid for original purchaser at original site of delivery with proof of purchase and photo documentation only. Warranty is

void upon transfer of ownership. Warranty does not apply to products installed in any commercial, rental, or non-residential application. Warranty covers

replacement parts only. Manufacturer is not responsible for labor or labor-related costs. Warranty does not cover discoloration, surface rust, corrosion,

or oxidation, which may occur due to harsh environments, chemicals, or overheating. Warranty will not apply for damage resulting from improper

installations, abuse, extreme environments, grease res, or misuse. Proof of regular and proper maintenance is required. Coastal, humid, and/or salt

environments are subject to manufacturer review. All out-of-box claims must be made within 30 days of purchase and must be made prior to installation.

Any product installed damaged will be considered damaged during installation and not covered under warranty. This warranty gives you specic legal

rights, and you may also have other rights which vary from state to state.

TO OBTAIN WARRANTY PROTECTION UNDER THE NOVO LIMITED WARRANTY, YOU MUST SUBMIT A COMPLETED

REGISTRATION FORM ONLINE AT www.novogrills.com WITHIN 30 DAYS OF THE PURCHASE DATE. FAILURE TO SUBMIT THE

REGISTRATION FORM WILL VOID THE LIMITED WARRANTY PROTECTION.

Please be advised - all display models are sold “as is” and the warranty covers the following items only: main burners (Limited Lifetime Warranty), grates