Ecoflam MAXFLAM 30 AB User manual

Technical data
Dati tecnici
Données techniques
Datos técnicos
Технические характеристики
Operating instructions
Istruzioni per l’uso
Notice d’emploi
Manual de uso
Руководство по эксплуатации
Electric diagrams
Schemi elettrico
Schémas électrique
Esquemas eléctrico
Электрические схемы
Spare parts list
Pièces de rechange
Parti ricambi
Piezas de recambio
Запчасти
www.ecoflam-burners.com
EN
IT
FR
ES
RU
MAXFLAM 30 AB
MAXFLAM 50 AB
MAXFLAM 30 AB TC 230-400-50 3142600
MAXFLAM 30 AB TL 230-400-50 3142601
MAXFLAM 50 AB TC 230-400-50 3142602
MAXFLAM 50 AB TL 230-400-50 3142603
HEAVY OIL BURNERS

Technical data
Dati tecnici
Données techniques
Datos técnicos
Технические характеристики
EN
IT
FR
ES
RU
3
Working fields
Campi di lavoro
Domaine de fonctionnement
Ámbito de funcionamiento
Рабочий диапазон
EN
IT
FR
ES
RU
4
Dimensions
Dimensioni
Dimensions
Dimensiones
Размеры
EN
IT
FR
ES
RU
5
Operating instructions for authorised specialists EN 6 - 18
Istruzione per l’uso per il personale qualificato IT 19 - 31
Notice d’emploi pour l’installateur spécialiste FR
Instrucciones de montaje para el instalador especialista ES
Инструкция по эксплутации Предназначено для
квалифицированных специалистов по установке RU 32 - 44
Electric diagrams
Schemi elettrico
Schémas électrique
Esquemas eléctrico
Электрические схемы
EN
IT
FR
ES
RU
45 - 46
Spare parts list
Parti di ricambio
Pièces de rechange
Piezas de recambio
Запчасти
EN
IT
FR
ES
RU
47 - 48
Overview - Index of contents / Panoramica - Indice dei contenuti / Vue d'ensemble - Table des matières
Descripción - Sumario / Обзор - Содержание
RU
ES
FR
IT
EN
420010405502
www.ecoflam-burners.com
2

Technical data - Dati tecnici - Données techniques - Datos técnicos - Технические характеристики MAXFLAM 30 AB MAXFLAM 50 AB
Burner output max/min kW - kcal/h
Potenza bruciatore max/min kW - kcal/h
Puissance du brûleur max/min kW - kcal/h
Potencia del quemador máx/min kW - kcal/h
Мощность горелки макс./мин., кВт -ккал/час
410 205 570 205
352800 176400 490000 176400
Oil throughput max/min kg/h
Portata gasolio max/min kg/h
Débit de fuel max/min kg/h
Caudal de gasóleo máx/min kg/h
Расход топлива макс./мин., кг/ч 36 18 50 18
Operation type (stage)
Sistema idraulico (stadio)
Système hydraulique 2 allure
Sistema hidráulico 2 etapa
Гидросистема 2 ступень 2 2
Regulating ratio Rapporto di
regolazione Rapport de régulation Relación de
regulación
Коэффициент регулирования 1:2
Fuel oil Combustibile Fuel Combustible Топливо
Heavy oil (L.C.V. 9.800 kcal/kg max. visc 50°E at 50°C)
Emission class Classe di emissione Classe d’émission Tipo de emisión Класс выделения
загрязняющих веществ -
Control box Apparecchiatura di
controllo Coffret de sécurité Cajetín de seguridad Блок управления и
безопасности Landis LMO 44
Air regulation Air flap
Regolazione aria Serranda dell'aria
Réglage de l’air Volet d’air
Ajuste del aire Válvula de aire
Настройка подачи воздуха Воздушная заслонка
--
Flame monitor Rivelatore di fiamma Surveillance
de flamme Vigilancia de llama Контроль пламени photoresistor photoresistor
Ignition transformer Trasformatore
d'accensione Allumeur Encendedor Устройство розжига cofi cofi
Fuel-oil pump Pompa di pressione Pompe de
pulvérisation
Bomba de pulverización
Насос распыления мазут suntec suntec
Electric motor rpm - watt
Motore elettrico giri motore - watt
Moteur rpm - watt
Motor rpm - watt
Электродвигатель об/мин - watt
2800 rpm 2800 rpm
740 W 1100 W
Voltage Tensione Tension Tensión Напряжение 230/400 V / 50 Hz
Power consumption (operation)
Potenza elettrica assorbita (Esercizio)
Puissance électrique absorbée (en service)
Pot. eléctrica absorbida
(en funcionamiento)
Потребляемая электрическая мощность: (при работе)
6000 W 6500 W
Net weight Peso netto Poids net Peso neto Приблизительная масса 65,5 kg 65,5 kg
Protection level Classe di protezione Indice de protection Índice de protección Класс электрозащиты IP40
Sound pressure level dB(A)
Livello pressione sonora dB(A)
Niveau presion acoustique dB(A)
Nivel de presion acústico dB(A) Уровень шума, dB(A) 74 76
Ambient temp. for storage
Temperatura ambiente di stoccaggio
Température ambiante de stockage
Temperatura ambiente de almacenamiento температура хранения -20°…+60° C
Temperature for use
Temperatura d’utilizzazione
Température d’utilisation
Temperatura ambiente de utilización Рабочая температура -10°…+60° C
Overview / Panoramica / Vue d'ensemble / Descripción / Обзор
RU
ES
FR
IT
EN
420010405502 www.ecoflam-burners.com 3

Working field The working field shows burner output as a function of combustion chamber pressure. It corresponds to the maximum values specified by EN 267 measured at the test fire tube. The efficiency rating of the boiler should be taken into account when selecting a burner. Calculation of burner output: QF = QN
ηK
QF = Burner output (kW) QN = Rated boiler output (kW) ηK= Boiler efficiency (%)
Curva Il campo di attività indica la potenza del bruciatore in funzione della pressione della camera di combustione. Corrisponde ai valori massimi previsti dalla norma EN 267 misurati sul tubo della fiamma di controllo. In occasione della scelta del bruciatore si deve tenere conto del rendimento energetico della caldaia. Calcolo della potenza del bruciatore: QF = QN
ηK
QF= potenza bruciata (kW) QN= potenza nominale della caldaia (kW) ηK= rendimento energetico
della caldaia (%)
Domaine de fonctionnement Le domaine de fonctionnement correspond aux valeurs mesurées lors de l’homologation. Elle correspond aux valeurs max mesurées sur tunnel d’essai d’après l’EN 267. Pour le choix du brûleur, tenir compte du rendement de la chaudière. Calcul de la puissance calorifique: QF = QN
ηK
QF= Puissance calorifique (kW) QN= Puissance nominale chaudière (kW) ηK= Rendement chaudière (%)
Ámbito de funcionamiento El ámbito de funcionamiento corresponde a los valores registrados en el momento de la homologación. Corresponde a los valores máx medidos en el túnel de ensayo según la EN 267. Para la elección del quemador, se ha de tener en cuenta el rendimiento de la caldera. Cálculo de la potencia calorífica: QF = QN
ηK
QF = Potencia calorífica (kW) QN = Potencia nominal de la caldera (kW) ηK = Rendimiento de la
caldera (%)
Рабочий диапазон Рабочий диапазон соответствует значениям, измеренным при сертификации. Он соответствует максимальным значениям, измеренным в соответствии со стандартом EN 267 в стандартном канале. При выборе горелки необходимо учитывать КПД котла. Расчет тепловой мощности: QF = QN
ηK
QF = Тепловая мощность, кВт QN= Номинальная мощность котла, кВт ηK= КПД котла, %
Overview - Working fields / Panoramica - Curve / Vue d'ensemble - Domaine de fonctionnement / Descripción - Ámbito de funcionamiento / Обзор - Рабочий диапазон
mbar
0,0 1,0 2,0 3,0 4,0 5,0 6,0 7,0 8,0 9,0
100 150
200
250 300 350
400 450 500 550 600
kW
kcal/h*1000
Maxflam 30 AB
Maxflam 50 AB
100 150 200 250 300 350 400 450 500
kg/h
10 15 20 25 30 35 40 45 50
RU
ES
FR
IT
EN
420010405502
www.ecoflam-burners.com
4

Overview - Dimensions / Panoramica - Dimensioni / Vue d'ensemble - Dimensions / Descripción - Dimensiones / Обзор - Размеры
X
Y
Z
Packaging
Ø a
d..°
Ø b
Ø c
M
Model AB C DD1 EFGI L M
MAXFLAM 30 AB 562 302 260 205 325 653 160 280 185/200 185/200 M10 MAXFLAM 50 AB 562 302 260 205 325 653 160 280 185/200 185/200 M10
Model Ø a Ø b Ø c
MAXFLAM 30 AB 170 262 283 MAXFLAM 50 AB 170 262 283
Model XY Z Kg
MAXFLAM 30 AB 786 1045 565 74 MAXFLAM 50 AB 786 1045 565 74
D / D1 E
M
L
F
G
125
I
CB
AE
D - D1
G
F
I
L
M
248
230
MAX FLAM 30 - 50 AB
Boiler plate drilling
RU
ES
FR
IT
EN
420010405502 www.ecoflam-burners.com 5

Contents - Index - General warnings - Conformity declaration
Important notes
The MAXFLAM burners are designed for
the combustion of heavy oil.
Assembly, commissioning and
maintenance must be carried out only by
authorised specialists and all applicable
guidelines and regulations must be
observed.
Burner description
The MAXFLAM burner is a two-stage,
fully-automatic monoblock-type burner. It is
suitable for use, within its range of
performance, with boilers complying with
EN 303 or hot-air generators in line with
DIN 4794, DIN 30697 or EN 621.
Use for any other application requires the
approval of Ecoflam.
The following standards should be
observed in order to ensure safe,
environmentally sound and energy-efficient
operation:
EN 60335-2
Safety of electrical equipment for domestic
use.
Installation location
The burner must not be operated in rooms
containing aggressive vapours (e.g. spray,
perchloroethylene, hydrocarbon
tetrachloride, solvent, etc.) or tending to
heavy dust formation or high air humidity.
Adequate ventilation must be provided at
the place of installation of the furnace
system to ensure a reliable supply with
combustion air.
Variations may arise as a result of local
regulations.
We can accept no warranty liability
whatsoever for loss, damage or injury
caused by any of the following:
- Inappropriate use.
- Incorrect assembly or repair by the
customer or any third party, including the
fitting of non-original parts.
Provision of the system and the
operating instructions
The firing system manufacturer must
supply the operator of the system with
operating and maintenance instructions on
or before final delivery. These instructions
should be displayed in a prominent
location at the point of installation of the
heat generator, and should include the
address and telephone number of the
nearest customer service centre.
Notes for the operator
The system should be inspected by a
specialist at least once a year. It is
advisable to take out a maintenance
contract to guarantee regular servicing.
Declaration of conformity
for oil burners
We,
Ecoflam Bruciatori S.p.A.
declare under our sole responsibility
that the heavy oil burners named
MAXFLAM....
conform to the following standards:
EN 267: 2010
EN 60335-1: 2008
EN 60335-2-30: 2006
EN 60335-2-102: 2007
EN 55014-1: 2008 + A1: 2009
EN 55014-2: 1998 + A1: 2001 + A2:
2008
These products bear the CE mark in
accordance with the stipulations of the
following directives:
2006/95/EEC Low Voltage Directive
2004/108/EEC EMC Directive
2006/42/EC Machinery directive
Resana, 28th June 2011
M. PANIZZON
Ecoflam burners have been designed and built in compliance with all current regulations
and directives.
All burners comply to the safety and energy saving operation regulations within the standard
of their respective performance range. The quality is guaranteed by a quality and management
system certified in accordance with ISO 9001:2008.
Overview Technical data 3
Working fields 4
Dimensions 5
Contents Index 6
General warnings 6
Conformity declaration 6
Burner description 7
Function General safety functions 8
Landis LMO 44 control and safety unit 9
Oil burner pump 10
Installation Burner assembly 11
Electrical connection 12
Checks before commissioning 12
Heavy oil feeding and suction line 13
Start up Setting data table - air regulation 15
Adjusting burner output 16
Oil pressure regulation 16
Service Maintenance 17
Troubleshooting 18
Overview Electrical diagrams 45-46
Spare parts list 47-48
420010405502
EN
www.ecoflam-burners.com
6

A1 Landis LMO44 control box
M1 Electric motor for pump and
blower wheel
T1 Ignition transformer
5 Fastening screws for equipment plate
9 Electric switch board
15 Burner flange
16 Release knob
102 Heavy-oil pump
103B Air regulation
113 Air intake
Contents - Burner description
Scope of delivery
CB: COMPLETE BURNER
- 1 bag including :
- multilanguage technical manual.
- filter and hoses.
- nozzle and spanner.
- screws, nuts and washer.
KIT & ACS delivered separately
15
113
9
103B
M1
15
102
MAXFLAM 30 AB TC 230-400-50
MAXFLAM Heavy oil
RANGE NAME BY FUEL TYPE
MAXFLAM 30 30 kg/h - 349 kW
MODEL SIZE (Gas: kW; Oil: kg/h)
OPERATION TYPE
TC Short head
TL Long head
HEAD TYPE
Heavy oil
FUEL
230-400-50 230-400 Volt, 50 Hz
ELECTRICAL POWER SUPPLY
- 1 stage
AB 2 stages
420010405502
EN
www.ecoflam-burners.com 7
16 A1
T1
5

Function - General safety functions
Operating function
- Switch-on the burner. When reaching
the preset temperature on the working
thermostat, and with boiler’s thermostat
closed, the control box starts the fan,
the fuel pump and the ignition
transformer. At the same time, the
resistors are activated, to keep fuel
temperature into the heater at a
constant value.
- The motor starts, the igniter is switched
on and the preventilation period of 25
seconds commences.
- During the preventilation period, the
furnace is monitored for flame signals.
- At the end of the preventilation period,
the fuel-oil solenoid valve opens and the
burner starts.
- The igniter remains switched off while
the burner is in operation.
Controlled shutdown
- Boiler thermostat interrupts heat
request.
- The fuel-oil solenoid valve closes and
the flame is extinguished.
- Burner motor switches off.
- Burner enters standby.
Safety function
A safety shutdown occurs:
- if a flame signal is present during
preventilation (parasitic flame
monitoring).
- if no flame is produced within 5 seconds
(safety time) of start-up (fuel
authorisation).
- if no flame is produced after an
unsuccessful restart attempt in the
event of flame failure during operation.
A safety shutdown is indicated by the
malfunction lamp lighting up and it is then
only possible to reenable the burner by
pressing the reset button after the cause
of the malfunction has been rectified.
For further information, see the
automatic combustion control unit
description.
O
F
H
E
GI
D
A
B
N
Legend :
A. Low Flame solenoid valve (N.C.)
B. High Flame solenoid valve (N.C.)
D. Orifice.
E. Tank..
F. Anti-gas valve.
G. Heater.
H. Filter.
I. Fuel pump.
N. Manometer.
O. Solenoid valve (N.O.).
N.C. = Norm. closed
N.O. = Norm. open
420010405502
EN
www.ecoflam-burners.com
8

!Always disconnect the power supply before installing or removing the control unit. Do not attempt to open or carry out repairs
on the control unit.
Function - Landis LMO44 control and safety unit
Connection diagram and internal diagram LMO44… Control sequence LMO44…
126745
10 11 12
W
SB
R
L
N
MZBV1
AL
Si
83
OW
OH
N
83
QRB
QRC
br
bl sw
1
7130a04/1105
9
EK2
EK1 µC-Steuerung
K1 K2
K4
BV2
LED
kbr
FSV
µC2
µC1
K3
R
W
SB
OH
OW
M
Z
BV2
FS
A´ AB C D
1
8
3
3
6
5
11
12
t1´
t3 t3n
TSA
tw
BV1 4
t4
t1
7130d05/1105
AL Alarm device
BV... Fuel valve
EK1 Lockout reset button
EK2 Remote lockout reset button
FS Flame signal
FSV Flame signal amplifier
K... Contacts of control relay
kbr Cable link (required only
when no oil preheater is used)
LED 3-color signal lamp
M Burner motor
OW Release contact of oil preheater
OH Oil preheater
QRB... Photoresistive flame detector
QRC... Blue-flame detector
bl = blue, br = brown, sw = black
R Control thermostat or
pressurestat
SB Safety limit thermostat
Si External primary fuse
W Limit thermostat or pressure
switch
Z Ignition transformer
TSA Ignition safety time
tw Waiting time
t1 Prepurge time
t1´ Purge time
t3 Preignition time
t3n Postignition time
t4 Interval from flame signal to
release of «BV2»
A´ Start of startup sequence with
burners using an «OH»
A Start of startup sequence with
burners using no «OH»
B Time of flame establishment
C Operating position
D Controlled shutdown by «R»
Color code table for multicolor signal lamp (LED)
Status Color code Color
Waiting time «tw», other waiting states
❍................................................................................... Off
Oil preheater on, waiting time «tw»
●................................................................................... Yellow
Ignition phase, ignition controlled ● ❍ ● ❍ ● ❍ ● ❍ ● ❍ ● ❍ ● ❍ ● ❍ ● ❍ ● ❍ ● ❍ Flashing yellow
Operation, flame o.k. ❑................................................................................... Green
Operation, flame not o.k. ❑ ❍ ❑ ❍ ❑ ❍ ❑ ❍ ❑ ❍ ❑ ❍ ❑ ❍ ❑ ❍ ❑ ❍ ❑ ❍ ❑ ❍ Flashing green
Extraneous light on burner startup
du bruleur ❑ ▲ ❑ ▲ ❑ ▲ ❑ ▲ ❑ ▲ ❑ ▲ ❑ ▲ ❑ ▲ ❑ ▲ ❑ ▲ ❑ ▲ Green-red
Undervoltage ● ▲ ● ▲ ● ▲ ● ▲ ● ▲ ● ▲ ● ▲ ● ▲ ● ▲ ● ▲ ● ▲ Yellow-red
Fault, alarm ▲................................................................................... Red
Error code output (refer to «Error code
table») ▲ ❍ ▲ ❍ ▲ ❍ ▲ ❍ ▲ ❍ ▲ ❍ ▲ ❍ ▲ ❍ Flashing red
Interface diagnostics ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ Red flicker light
Legend: ....... Steady on ▲ Red ❑ Green
❍ Off ● Yellow
420010405502
EN
www.ecoflam-burners.com 9

Function - Oil burner pump
1 suction intake connection.
2 return connection.
3 oil pressure gauge connection.
4 negative pressure gauge connection.
5 oil pressure regulator.
6 pressure connection
SUNTEC E
PUMP
IDENTIFICATION
Gear set capacity
(see pump capacity curves)
)Pressure regulation
Filter
Shaft rotation
and nozzle location
(seen from shaft end)
E 4 N C 1 069 7 P
Flange mounting
069 :
model without cut-off function
P : by-pass plug installed in return port
for two-pipe operation
(vista lato albero)
A : clockwise rotation/
right hand nozzle.
C: anti clockwise rotation/
left hand nozzle. izquierdo
body with
preheater cavity
Revision number
Installation
(Not all model combinations are available
Consult your Suntec representative)
Tenuta
albero
Pressure
gauge port
Gear set
To nozzle
Pressure
adjustment
Back
to suction
By-pass
plug
inserted
By-pass
plug
removed
Return
Inlet
ONEPIPE
INSTALLATIONReturn
plugged
TWOPIPE
INSTALLATION
Vacuum
gauge port
Oil under pressure
Oil under suction
By-passed oil
returned to tank,
or to suction
By-pass hole
Inletand return G1/2"
Nozzle outletG1/4"
Pressure gauge port G1/8"
Vacuum gauge port G1/2"
General
Mounting
Connection threadsCylindrical according to ISO 228/1
ShaftØ11mm according to EN 225.
By-pass plug Insertedinreturn port for 2 pipe system;
to be removedwith a3/16" Allenkey
for 1 pipe system.
Weight4 kg
Hydraulic data
Nozzle pressure range14 - 30 bar
Operating viscosity3 - 75 cSt
0 - 130°C max. nellapompa
installation to lightoil : 0,45 bars max.
vacuum to prevent airseparation from oil.
installation to heavy oil : 3,5 bar max.
Return pressureinstallation to lightoil : 3,5 bar max.
installation to heavy oil : 3,5 bar max.
Ratedspeed3600 gpm max.
Torque(to 40 gpm) 0,3 N.m
Choice of heater
Crtridge Ø12 mm
Fitting inaccordo con EN 50262
Rating 50-80 W
Valve function Pressure regulating - no cut-off
FilterOpenarea: 45 cm²
Opening size ѥP
Capacity (L/h)
Capacity (L/h)
Pressure (bar)
Pressure (bar)
Viscosity = 200 cSt
20 cSt
5 cS Ratedspeed= 2850 gpm
TECHNICAL DATA
Flange mounting according to EN 225.
Delivery pressure setting 20 bar
Oil temperature
Inletpressure
Pump capacity
Data showntake into account awear margin.
Donot oversize the pump whenselecting the
gear capacity.
The heavy oil burner pump used is a self-
priming gear pump, which must be
connected as two-line pump via a bleed
filter. There is an intake filter and an oil
pressure regulator integrated in the pump.
Pressure gauges for pressure
measurements and negative pressure
measurements must be connected before
the equipment is commissioned.
NB: before starting the burner, check that
the return pipe is open. An eventual
obstraction could damage the pump
sealing device.
420010405502
EN
www.ecoflam-burners.com
10

Installation - Burner assembly
Oil connection
The filter must be located in such a way
that the correct hose routing cannot be
impaired. The hoses must not kink.
Burner assembly
The burner is fixed by the flange and
therefore to the boiler.
Installation:
• To fix the flange to the boiler with
the screws.
Removal:
• Loosen the screws.
• To slowly slide the the burner from the
boiler.
Burner pipe insertion depth and
brickwork
Unless otherwise specified by the boiler
manufacturer, heat generators without a
cooled front wall require brickwork or
insulation 5 as shown in the illustration.
The brickwork must not protrude beyond
the leading edge of the flame tube, and
should have a maximum conical angle of
60°. Gap 6 must be filled with an elastic,
non-combustible insulation material. For
boilers with reverse firing, the minimum
burner tube insertion depth A as
specified in the boiler manufacturer’s
instructions must be observed.
Exhaust system
To avoid unfavourable noise emissions,
right-angled connectors should not be
used on the flue gas side of the boiler.
1
2
–
420010405502
EN
www.ecoflam-burners.com 11

Installation - Electrical connection - Checks before commissioning
Electrical connection
The electrical installation and connection
work must only be carried out by an
authorised electrical specialist.
All applicable rules and regulations must
be observed.
The electrical installation should include a
type A circuit breaker.
The applicable guidelines and
directives must be observed, as well as
the electrical circuit diagram supplied
with the burner!
• Check to ensure that the power supply
voltage is as specified in the electric
diagram and in data plate.
• Burner fuse: 5 A.
Checks before commissioning
The following must be checked before
initial commissioning:
• That the burner is assembled in
accordance with the instructions given
here.
• That the burner is pre-set in accordance
with the values in the adjustment table.
• Setting the combustion components.
• The heat generator must be ready for
operation, and the operating regulations
for the heat generator must be observed.
• All electrical connections must be correct.
• The heat generator and heating system
must be filled with water and the
circulating pumps must be in operation.
• The thermostats, pressure regulator, low
water detectors and any other safety or
limiting devices that might be fitted must
be connected and operational.
• The exhaust gas duct must be
unobstructed and the secondary air
system, if available, must be operational.
• An adequate supply of fresh air must be
guaranteed.
• The heat request must be available.
• Fuel tanks must be full.
• The fuel supply lines must be
assembled correctly, checked for leaks
and bled.
• A standard-compliant measuring point
must be available, the exhaust gas duct
up to the measuring point must be free of
leaks to prevent anomalies in the
measurement results.
Position of electrodes
Note: Always check the position of
electrodes after having replaced the
nozzle (see illustration). A wrong position
could cause ignition troubles.
12
RP
6 7 8
RA1
2221 26 25
TP
STAB RA2 R0
5
P
T
STS
HLB HLF
P
T
STC
Q
S
N
T
50 Hz 400V
PE
R
NR TS 1 2 3 4 109 11
SECTION A-A
4
4/5
A
A
/56
420010405502
EN
www.ecoflam-burners.com
12

Installation - Heavy oil feeding and suction line
T
T
A
B
C
A A
Sez. A - A
A - Isolation gasket
B - Heater
C - Pipe heavy oil
1 - Burner
2 - Tank
3 - Heater
4 - Thermostat
5 - Transfer pump
6 - Header
7 - Tank
8 - By-pass
9 - Pressure regulating valve
1
1
1
2
2
3
3
4
4
5
5
5
6
6
7
7
8
9
IMPORTANT: All fuel pipings are heated (see section A-A of the picture)
420010405502
EN
www.ecoflam-burners.com 13
HEAVY OIL FEED SYSTEM UP TO 15°E AT 50°C

14 www.ecoflam-burners.com
EN
420010405502
Hot
water
Return
hot water pipe
oil pipe oil pipe
heating cable
hot water pipe
insulation
1 - Burner
2 - Tank
3 - Heater
4 - Safety thermostat
5 - Level switch
6 - Heating coil
7 - Filter
8 - Load pumps
9 - Ring pumps
10 - Pressure regolator
11 - Heating cable
IMPORTANT: All feed piping are heated (see sec. A-A)
Installation - Heavy oil feeding and suction line
HEAVY OIL FEED SYSTEM UP TO 50°E AT 50°C

15
www.ecoflam-burners.com
EN
420010405502
A
Start up - Setting data table - Air regulation
The settings above are basic settings.
These adjustment values are normally
suitable for commissioning the burner.
These values have been determined in
our test labs and are useful for the first
switch-on as final setting must be done
using a combustion analyzer.
Favourable combustion values can be
achieved using the following nozzles:
DANFOSS H÷S 80°÷60°
DELAVAN W 60°
STEINEN S 60°
Air damper setting (A).
Remove the cover to gain access to the
adjustment cams. The cams are adjusted
using the screwdriver.
Descrıption:
I - Limit switch for the “HIGH FLAME“
position of the air damper
(MAX POWER).
II - Adjusting cam for the air damper
position at shut down (0°).
III - Auxiliary switch for the release of the
second stage valve (HIGH FLAME).
IV - Limit switch for the “LOW FLAME“
position of the air damper.
B
Note : Cam III (to enable the stage two
electrovalve to open) is adjusted to an in-
termediate position between the low flame
and high flame positions (to an angle ap-
proximately 5° greater than the low flame
position).
Firing head setting (B).
Slide the burner out off mounting flange.
Modify air cilynder position (1,2,3,4) as
shown in fig.B using a screwdriver. Slide
again the burner in the mounting flange
end fix to the boiler.
Maxflam 30 AB
burner output
kW
pressure in
combustion
chamber
mbar
oil output
kg/h
nozzle 60° HO
pump
pressure
bar
firing head
setting
air damper setting
1° stage 2° stage 1° stage 2° stage 1° stage 2° stage 1° stage 2° stage 1° stage stage
205 274 1,6 3,3 18 24 3,00 1,00 23 1 18° 30°
239 331 1,3 3,7 21 29 3,50 1,50 23 2 20° 40°
274 388 1 4 24 34 4,00 2,00 23 3 20° 60°
Maxflam 50 AB
burner output
kW
pressure in
combustion
chamber
mbar
oil output
kg/h
nozzle 60° HO
pump
pressure
bar
firing head
setting
air damper setting
1° stage 2° stage 1° stage 2° stage 1° stage 2° stage 1° stage 2° stage 1° stage stage
205 296 1,5 3,5 18 26 3,00 1,50 23 1 15° 40°
262 388 1,3 4 23 34 4,00 2,00 22 2 20° 50°
308 479 1,4 4,7 27 42 4,50 2,50 23 3 20° 50°

Start up - Adjusting burner output - Oil pressure regulation
Burner start
Before starting the burner, draw oil in until
the filter is completely filled.
Then start the burner by switching on the
boiler regulator. Open the bleed screw on
the oil filter to allow the oil line to bleed
fully during the preventilation phase. The
negative pressure must not fall below 0.4
bar. Close the bleed screw when the filter
is completely filled with oil and oil is
flowing out without bubbles.
Burner output adjustment
Use the pressure regulator to adjust the oil
pressure in accordance with the burner
output desired. Monitor the combustion
values continuously as you do so (CO,
CO2, soot test). Adjust the airflow
gradually if necessary.
Optimising combustion values
If the combustion values are not
satisfactory modify the position of the
combustion head. By doing this the burner
ignition conditions and the combustion
values change. Compensate for the
change in airflow if necessary by adjusting
the air flap position.
Note: observe the minimum required
flue gas temperature specified by the
boiler manufacturer and the
requirements demanded of flue gas
ducts for avoiding condensation.
Oil pressure regulation
The oil pressure, and therefore burner
output, is adjusted using oil pressure
regulator 5in the pump.
Turn to
- right: to increase pressure
- left: to reduce pressure
Connect a pressure gauge at point 3(with
R1/8" thread).
Checking negative pressure
The vacuum meter for checking negative
pressure must be connected to point 4,
R1/8". Maximum permissible negative
pressure is 0.4 bar. At higher negative
pressures, the fuel oil gasifies, which
causes scraping noises in the pump and
ultimately leads to pump damage.
Operating check
Flame monitoring must be checked for
safety as part of initial commissioning and
also after servicing or if the system has
been out of operation for any significant
period of time.
- Starting attempt with flame monitor unlit:
the automatic combustion control unit
must switch to malfunction at the end of
the safety time
- Start with flame monitor lit: the
automatic combustion control unit
must switch to malfunction after 5
seconds of preventilation
- Normal start-up: flame monitor goes out
when burner in operation; the automatic
combustion control unit must switch to
malfunction after the restart and end of
the safety time
!Risk of air blast!
Continuously check CO, CO2and soot emissions when adjusting the output of
the burner. Optimise combustion values in the event of CO formation. CO must
not exceed 50 ppm.
1 suction intake connection.
2 return connection.
3 oil pressure gauge connection.
4 negative pressure gauge connection.
5 oil pressure regulator.
6 pressure connection
SUNTEC E
Adjustment of fuel thermostats
The working resistor thermostat must be
set to 100°-140°C, while the safety ther-
mostat is preset. Said adjustments can be
slightly modified following the type of fuel
and particular uses.
A - Working thermostat (100°-140° C).
B - Stand-By thermostat (150° C).
C - Firing head thermostat (120°-140° C).
420010405502
EN
www.ecoflam-burners.com
16

Service - Maintenance
Fan assembly
Observe the positioning diagram below
when replacing the motor and blower
wheel. The inside flange Aof the blower
wheel must be fitted at the same level as
the equipment plate B. Insert a straight
edge between the wing of the blower wheel
and set Aand Bto the same height, tighten
the set screw on the blower wheel.
Burner and boiler servicing must only
be carried out by qualified personell.
The system operator is advised to take
out a service contract to guarantee
regular servicing.
Attention
• Disconnect the electrical supply before
carrying out any maintenance or
cleaning work.
• The blast tube and firing head may be
hot.
Checking the exhaust gas temperature
• Check the flue gas temperature at
regular intervals.
• Clean the boiler if the flue gas
temperature is more than 30°C above
the value measured at the time of
commissioning.
• To simplify the check, use a flue gas
temperature indicator.
Burner maintenance positions
• After removing the screws pull the burner
out of the flange and turn to maintenance
(as show in picture) to :
nozzle change
electrodes change and setting
combustion disc cleaning/change
air cylinder setting
Maintenance on the burner
• Clean fan and housing and check for
damage.
• Check and clean the combustion head.
• Replace oil nozzle.
• Check ignition electrodes, readjust or
replace as necessary.
• Fit combustion head. Observe
adjustment dimensions.
• Fit burner.
• Start burner, check flue gas data, correct
burner settings if necessary.
• Check oil supply components (tubes,
pumps, oil feed tube) and their
connections for leaks or signs of wear,
replace if necessary.
• Check electrical connections and
connection cables for damage, replace if
necessary.
• Check pump filter and clean if
necessary.
Nozzle and cleaning replacement
Use only the suitable box wrench provided
for this operation to remove the nozzle,
taking care to not damage the electrodes.
Fit the new nozzle by the same care.
–
+
B
A
C
Cleaning of filter on the preheater
Removing of the filter:
1 Switch-off the burner and make cold to
leave.
2 Take off oil thermometer bulb C.
3 Loosen screw B and drain part of the fuel
from the heater, until the fuel level drop
below the filter.
4 Unscrew and pull out the stem filter A from
its seat.
5 Clean the filter and reassemble the parts
as shown by the picture, then fit it in its own
seat.
It is advisable to replace all filter and valve
gaskets whenever they are removed.
Note: that when the burner is working
the heater has a pressure of abt. 23 bar,
and that it becomes very dangerous to
carry out said operations with the burner
running.
Note: Always check the position of
electrodes after having replaced the
nozzle (see illustration). A wrong position
could cause ignition troubles.
420010405502
EN
www.ecoflam-burners.com 17

Fault diagnosis and repair
In the event of a malfunction, first check
that the prerequisites for correct operation
are fulfilled:
1. is the system connected to the power
supply?
2. is there oil in the tank?
3. are all shut-off valves open?
4. are all control and safety devices,
such as the boiler thermostat, low-water
detector, limit switch, etc.
adjusted correctly?
If the malfunction persists, use the
following table.
It is not permitted to repair any
components relevant to safety. These
components must be replaced by parts
with the same order number.
Only use original spare parts.
NB: after each operation:
• under normal operating conditions
(doors closed, hood fitted, etc.), check
combustion and check the individual
lines for leaks.
• Record the results in the relevant
documents.
Service - Troubleshooting
Error code table
Red blink code of «AL» at Possible cause
signal lamp (LED)) term. 10
2 blinks on No establishment of flame at the end of «TSA»
- Faulty or soiled fuel valves - Faulty or soiled flame detector
- Poor adjustment of burner, no fuel - Faulty ignition equipment
3 blinks on Free
4 blinks on Extraneous light on burner startup
5 blinks on Free
6 blinks on Free
7 blinks on Too many losses of flame during operation
(limitation of the number of repetitions)- Faulty or soiled fuel valves.
- Faulty or soiled flame detector - Poor adjustment of burner.
8 blinks on Time supervision oil preheater
- Oil preheater failed 5 times during prepurging
9 blinks on Free
10 blinks off Wiring fault or internal fault, output contacts,other faults.
on 3 times temporary fault of the output contacts
420010405502
EN
www.ecoflam-burners.com
18

Contenuti generali - Indice - avvertenze generali - dichiarazione di conformità
Avvertenze importanti
I bruciatori MAXFLAM sono progettati per
la combustione di olio pesante.
Montaggio, messa in funzione e
manutenzione devono essere eseguiti
esclusivamente da personale tecnico
autorizzato, nel rispetto delle direttive e
delle prescrizioni in vigore.
Descrizione del bruciatore
Il bruciatore MAXFLAM è bistadio, a
funzionamento completamente
automatico in esecuzione monoblocco.
E' adatto per l'allestimento di tutti i
generatori di calore conformi alla norma
EN 303 e/o degli aerotermi secondo
DIN 4794, DIN 30697 o EN621
nell'ambito del suo range di potenza.
Per qualsiasi altro utilizzo è richiesta
l'autorizzazione della Ecoflam.
Al fine di garantire un funzionamento
sicuro, non inquinante ed a basso
consumo energetico, è necessario
rispettare le seguenti norme:
EN 60335-2
Apparecchi elettrici di sicurezza per uso
domestico.
Luogo di installazione
Il bruciatore non dev'essere messo in
funzione in locali in cui siano presenti
vapori aggressivi (ad es. lacca per capelli,
percloroetilene, tetracloruro di carbonio),
notevole accumulo di polvere o forte
umidità dell'aria (ad es. lavanderie).
Una adeguata ventilazione deve essere
fornita nel locale dell’installazione in modo
da garantire le condizioni per una buona
combustione.
Si possono riscontrare scostamenti
dovuti ad eventuali normative locali.
Si esclude qualsivoglia responsabilità
per eventuali danni derivanti dalle
seguenti cause:
- utilizzo non conforme.
- montaggio difettoso e/o riparazione a
cura dell'acquirente o terzi, ivi inclusa
l'applicazione di elementi di origine
estranea.
Consegna e istruzioni per l'uso
Il costruttore dell'impianto di
combustione è tenuto a consegnare al
gestore dell'impianto, al più tardi all'atto
della consegna dello stesso, le
istruzioni per l'uso e la manutenzione.
Queste istruzioni devono essere
appese nel locale di installazione del
generatore termico in modo ben visibile.
Devono essere indicati l'indirizzo ed il
numero telefonico del punto di
assistenza più vicino.
Avvertenza per il gestore
L'impianto dev'essere controllato almeno
una volta l'anno da un tecnico
specializzato. Al fine di garantire
un'esecuzione regolare, si suggerisce di
stipulare un contratto per la manutenzione
dell'impianto.
Dichiarazione di conformità
per bruciatori ad olio
Noi,
Ecoflam Bruciatori S.p.A.
dichiariamo sotto la nostra
responsabilità, che i bruciatori ad olio
MAXFLAM...
sono conformi alle norme elencate:
EN 267: 2010
EN 60335-1: 2008
EN 60335-2-30: 2006
EN 60335-2-102: 2007
EN 55014-1: 2008 + A1: 2009
EN 55014-2: 1998 + A1: 2001 + A2:
2008
Questi prodotti vengono contrassegnati
con il marchio CE nel rispetto delle
direttive:
2006/95/EEC Low Voltage Directive
2004/108/EEC EMC Directive
2006/42/EC Machinery directive
Resana, 28 giugno 2011
M. PANIZZON
I bruciatori Ecoflam sono stati progettati e costruiti nel rispetto delle normative e direttive correnti.
Tutti i bruciatori rispondono alle normative sulla sicurezza e sul risparmio energetico nel limite del
campo di lavoro dichiarato.
La qualità del prodotto è garantita dal sistema di certificazione in base alla norma ISO 9001:2008.
Panoramica Dati tecnici 3
Curve di lavoro 4
Dimensioni d’ingombro 5
Contenuti generali Indice 19
Avvertenze generali 19
Dichiarazione di conformità 19
Descrizione del bruciatore 20
Funzione Funzioni generali di sicurezza 21
Programmatore di comando e sicurezza Landis LMO44 22
Pompa del bruciatore 23
Installazione Montaggio del bruciatore 24
Connessione elettrica 25
Controlli da eseguire prima della messa in funzione 25
Linea di alimentazione del combustibile 26
Messa in funzione Dati di configurazione - regolazione dell’aria 28
Regolazione del bruciatore 29
Regolazione pressione del gasolio 29
Assistenza Manutenzione 30
Possibili inconvenienti 31
Panoramica Schemi elettrici 45-46
Parti di ricambio 47-48
420010405502
IT
www.ecoflam-burners.com 19

420010405502
IT
www.ecoflam-burners.com
20
A1 Landis LMO44 programmatore di
comando e sicurezza
M1 Motore elettrico per pompa e ventola
T1 Trasformatore d'accensione
5 Viti di fissaggio piastra
9 Pannello elettrico
15 Flangia bruciatore
16 Pulsante di sblocco
102 Pompa olio
103B Regolazione dell’aria
113 Cuffia aria
Contenuti generali - Descrizione del bruciatore
Imballaggio
CB: BRUCIATORE COMPLETO
- 1 sacchetto :
- manuale tecnico in multilingue.
- filtro e tubi flessibili.
- ugello e chiave per ugello.
- viti, dadi e rosette.
KIT & ACS ordinabili e
consegnati separatamente
15
113
9
103B
M1
15
102
MAXFLAM 30 AB TC 230-400-50
MAXFLAM Olio pesante
NOME
MAXFLAM 30 30 kg/h
MODELLO (Gas: kW; Olio pesante: kg/h)
TIPO DI FUNZIONAMENTO
TC Testa corta
TL Testa lunga
TIPO TESTA
Oilo combustibile: max visc. 50° E a 50°C
COMBUSTIBILE
230-400-50 230-400 Volt, 50 Hz
TENSIONE DI ALIMENTAZIONE
-1 stadio
AB 2 stadi
16 A1
T1
5