Novus NVAHD-1DN3102H/IR-1 User manual

NVAHD-1DN3102H/IR-1
u s e r ’s m a n u a l

NVAHD-1DN3102H/IR-1 - ver. 1.0 - User’s manual
All rights reserved © AAT Holding S.A.
2
INFORMATION
EMC (2004/108/EC) and LVD (2006/95/EC ) Directives
CE Marking
Our products are manufactured to comply with the requirements of the following directives and
national regulations implementing the directives:
 Electromagnetic compatibility EMC 2004/108/EC.
 Low voltage LVD 2006/95/EC with further amendment. The Directive applies to electrical
equipment designed for use with a voltage rating of between 50VAC and 1000VAC as well
as 75VDC and 1500VDC.
WEEE Directive 2002/96/EC
Information on Disposal for Users of Waste Electrical and Electronic Equipment
This appliance is marked according to the European Directive on Waste Electrical and
Electronic Equipment (2002/96/EC) and further amendments. By ensuring this product is disposed of
correctly, you will help to prevent potential negative consequences for the environment and human
health, which could otherwise be caused by inappropriate waste handling of this product.
The symbol on the product, or the documents accompanying the product, indicates that this appliance
may not be treated as household waste. It shall be handed over to the applicable collection point for
used up electrical and electronic equipment for recycling purpose. For more information about
recycling of this product, please contact your local authorities, your household waste disposal service
or the shop where you purchased the product.
RoHS Directive 2002/95/EC
Out of concern for human health protection and friendly environment, we assure that our
products falling under RoHS Directive regulations, regarding the restriction of the use of
hazardous substances in electrical and electronic equipment, have been designed and manufactured in
compliance with the above mentioned regulations. Simultaneously, we claim that our products have
been tested and do not contain hazardous substances whose exceeding limits could have negative
impact on human health or natural environment.
Information
The device, as a part of professional CCTV system used for surveillance and control, is not designed
for self installation in households by individuals without technical knowledge.
The manufacturer is not responsible for defects and damages that result from improper or inconsistent
with user’s manual installation of the device in the system.

NVAHD-1DN3102H/IR-1- ver. 1.0 - User’s manual
All rights reserved © AAT Holding S.A.
3
SAFETY REQUIREMENTS
WARNING!
THE KNOWLEDGE OF THIS MANUAL IS AN INDESPENSIBLE CONDITION OF A
PROPER DEVICE OPERATION. YOU ARE KINDLY REQUSTED TO FAMILIRIZE
YOURSELF WITH THE MANUAL PRIOR TO INSTALLATION AND FURTHER
DEVICE OPERATION.
WARNING!
USER IS NOT ALLOWED TO DISASSEMBLE THE CASING AS THERE ARE NO USER-
SERVICEABLE PARTS INSIDE THIS UNIT. ONLY AUTHORIZED SERVICE PERSONNEL
MAY OPEN THE UNIT
INSTALLATION AND SERVICING SHOULD ONLY BE DONE BY QUALIFIED SERVICE
PERSONNEL AND SHOULD CONFORM TO ALL LOCAL REGULATIONS
WARNING!
PRIOR TO UNDERTAKING ANY ACTION THAT IS NOT DESCRIBED FOR THE GIVEN
PRODUCT IN USER’S MANUAL AND OTHER DOCUMENTS DELIVERED WITH THE
PRODUCT, OR IF IT DOES NOT ARISE FROM THE USUAL APPLICATION OF THE
PRODUCT, MANUFACTURER MUST BE CONTACTED UNDER THE RIGOR OF
EXCLUDING THE MANUFACTURER’S RESPONSIBILITY FOR THE RESULTS OF SUCH AN
ACTION.
IMPORTANT SAFEGUARDS AND WARNINGS
1. Prior to undertaking any action please consult the following manual and read all the safety and
operating instructions before starting the device.
2. Please keep this manual for the lifespan of the device in case referring to the contents of this manual
is necessary;
3. All the safety precautions referred to in this manual should be strictly followed, as they have a
direct influence on user’s safety and durability and reliability of the device;
4. All actions conducted by the servicemen and users must be accomplished in accordance with the
user’s manual;
5. The device should be disconnected from power sources during maintenance procedures;
6. Usage of additional devices and components neither provided nor recommended by the producer
is forbidden;
7. Mounting the device in places where proper ventilation cannot be provided (e. g. closed lockers
etc.) is not recommended since it may lead to heat build-up and damaging the device itself
as a consequence;
8. Mounting the camera on unstable surface or using not recommended mounts is forbidden.
Improperly mounted camera may cause a fatal accident or may be seriously damaged itself. The
camera must be mounted by qualified personnel with proper authorization, in accordance with this
user’s manual.

NVAHD-1DN3102H/IR-1 - ver. 1.0 - User’s manual
All rights reserved © AAT Holding S.A.
4
SAFETY REQUIREMENTS
9. Device should be supplied only from a power sources whose parameters are in accordance with those
specified by the producer in the camera technical datasheet. Therefore, it is forbidden to supply the
camera from a power sources with unknown parameters, unstable or not meeting producer’s
requirements;
10. Signal cables (conducting TV or / and telemetric signal) should be placed in a way excluding the
possibility of damaging them by accident. Special attention must be paid to cables getting from the
camera and connecting the power supply;
11.
To avoid equipment damage, whole TV circuit should be equipped with properly made
discharge-, overload- and lightning protection devices. Usage of separating transformers is advised;
12. Electric installation supplying the device should be designed to meet the specifications given
by the producer in such a way that overloading is impossible;
13. User cannot repair or upgrade the equipment himself. All maintenance actions and repairs should
be conducted only by qualified service personnel;
14. Unplug the camera from the power source immediately and contact the proper maintenance
department when the following occurs:
 Damages to the power cord or to the plug itself;
 Liquids getting inside the device or exposure to strong mechanical shock;
 Device behaves in a way not described in the manual and all adjustments approved by the
manufacturer and possible to apply by user himself, seem not to have any effect;
 Camera is damaged;
 Atypical behaviour of the camera components may be seen (heard).
16. In necessity of repairs attention to using only original replacement parts (with their parameters
in accordance with those specified by the producer) should be paid. Non-licensed service and
non-genuine replacement parts may cause fire or electrocution;
17. After maintenance activities tests should be run to ensure proper operation of all the functional
components of the device.
Novus AHD cameras are dedicated to work with Novus AHD DVRs. Using only Novus products
guarantees the highest image quality. Connecting Novus AHD cameras to DVRs from other
manufacturers may decrease video quality.
Attention!
Technical changes reserved without prior notice and printing errors possible.

NVAHD-1DN3102H/IR-1- ver. 1.0 - User’s manual
All rights reserved © AAT Holding S.A.
5
1. PACKAGE CONTENTS
 NVAHD-1DN3102H/IR-1camera
 User’s manual
 A set of screws and dowels
 Allen key
 Mounting template
If any of the listed equipment has been damaged during transport or if the package is incomplete,
the contents of package should be packed back in to the original box. Please contact your local
NOVUS distributor for further assistance.
2. MAIN CHARACTERISTIC
 Mechanical IR cut filter
 IR operation capability
 Horizontal resolution: 720p
 Min. illumination: from 0.0013 lx/F=1.2 (0lx with IR on)
 Lens type: Varifocal, f=2,8 –12 mm
 Built-in IR illuminator: 2 LED
 Light sensor
 2DNR and 3DNR digital noise reduction
 WDR - wide dynamic range
 SENS-UP - digital slow shutter (DSS)
 BLC - back light compensation
 HLC - high light compensation
 DEFOG - improves visibility during fog and rain
 The ability to work in 720p AHD mode and analog 960H mode
 Stabilization of IR LED current for extending their service life
 Other functions:
– 4 motion detection zones,
– 4 privacy zones,
– mirror effect, freeze, negative image
– defective pixels correction
– defining the camera name
– adjusting the brightness and sharpness
 Operation in PAL and NTSC systems
 OSD menu
 Power supply: 12VDC
FOREWORD INFORMATION
To avoid equipment damage, whole TV circuit should be equipped with properly made

NVAHD-1DN3102H/IR-1 - ver. 1.0 - User’s manual
All rights reserved © AAT Holding S.A.
6
3. SPECIFICATION
SPECIFICATION
IMAGE
Pick-up element 1/4’’ APTINA, CMOS, 1.1 Mpx imager
Number of effective pixels 1280 (H) x 800 (V)
Horizontal resolution 720p
Min. illumination
0.03 lx/F=1.2 - color mode (1/50 s),
0.0013 lx/F=1.2 - b/w mode (1/50 s),
0 lx (IR on) – b/w mode
S/N ratio >60 dB
Electronic shutter auto/manual: 1/25s ~ 1/50 000s (for AHD) and 1/50s ~ 1/50 000s (for analog 960H)
Digital slow shutter (DSS) up to 30x
LENS
Type varifocal, f=2.8 - 12 mm/F=1.2
Angle of View (H) 26°- 70° (for AHD), 24° - 66° (for analog 960H)
DAY/NIGHT
Type mechanical IR cut filter
Switching Mode auto/manual
Switching Level Adjustment yes
Switching Delay 0-60 s
OTHER FUNCTIONS
OSD English, Polish, Russian and others
Back Light Compensation (BLC) yes
High Light Compensation (HLC) yes
Wide Dynamic Range (WDR) yes
Digital Noise Reduction (DNR) yes
Privacy Zones 4 zones
Motion Detection 4 zones
Image Processing mirror effect, rotate, sharpening
IR ILLUMINATOR
LED number 2
Range 30 m
Angle 60°
INTERFACES
Video output BNC, 1.0 Vp-p, 75 Ohm
INSTALLATION PARAMETERS
Dimensions (mm) 65 (H) x 77 (W) x 178 (L)
Weight 530 g
Enclosure aluminium, in ivory
Power Supply 12 VDC +/- 10%
Power Consumption 1 W (3,8 W IR on)
Operating Temperature -20ºC ~ 50ºC
Degree of protection IP 66
Defog yes

NVAHD-1DN3102H/IR-1- ver. 1.0 - User’s manual
All rights reserved © AAT Holding S.A.
7
3.1. Dimensions:
3.2. View of the camera, layout of the camera items:
SPECIFICATION/INSTALLATION
Screw of holder
Screw of kamera arm
Focus adjustment
Focusing
Joystick for menu operation
Service video output

NVAHD-1DN3102H/IR-1 - ver. 1.0 - User’s manual
All rights reserved © AAT Holding S.A.
8
4. INSTALLATION
Make sure the location can support 5 times the total weight of the bullet camera. Be careful not to
jam or peel insulation covering of the cable. This may result in malfunction or a fire hazard.
 Using the template, mark the position of the mounting holes
 Drill holes for the mounting screws and the hole for video and power cables
 Pass the power and video cables through the hole in the base of the camera
 Pass the cables through a previously prepared in the ceiling/wall hole
 Using screws included in the box, attach the base of the camera to the ceiling/wall
 Adjust the position of the camera and then lock them with position with suitable screws/nuts.
 Make the appropriate camera settings via the OSD menu
NOTE:
It is possible to switch camera into analog 960H mode, which is e.g. compatible with service
monitor. To change mode tilt the joystick to the left and hold for about 5 seconds. To return to
the AHD mode, tilt the joystick to the right and hold for about 5 seconds. The default mode of
the camera is AHD mode.
By pressing and holding the joystick down (DN) camera switches between PAL and NTSC sys-
tems. The default operating mode of the camera is PAL.
INSTALLATION
Handle screw
Screw sunshade
Mounting bracket
Sunshade
Photodetector
IR LED’s
Camera lens
Bottom cover
Bottom screw

NVAHD-1DN3102H/IR-1- ver. 1.0 - User’s manual
All rights reserved © AAT Holding S.A.
9
SETTINGS
4.1. Power supply connection
NOTE: Device should be supplied only from a power sources whose parameters are in accor-
dance with those specified by producer in the camera’s technical datasheet. Therefore, it is for-
bidden to supply the camera from power sources whose parameters are unknown, unstable or
not meeting the producer’s requirements.
5. SETTINGS
The camera has an OSD menu displayed in the foreground of image. During normal operation
status information can be displayed on the image. To navigate menu and make changes please use
joystick located on the bottom of the camera:
To enter the menu, press the joystick, which sends ENTER command to the device. To choose
submenu, select the UP, DOWN (UP, DN) directions. If the sub-menu contains the symbol  that
indicates the opportunity to enter to the settings by pressing the ENTER key. To change the parame-
ters of selected items, press LEFT, RIGHT buttons. To exit the menu and saves changes, select
EXIT and next select SAVE & END. By selecting RESET you can restore the factory settings, and
by selecting NOT SAVE you can exit the menu without saving changes. To exit the submenu, select
RETURN and press ENTER. Choosing (with left or right button) SAVE & END in the RETURN
position saves changes and closes the menu.
NOTE:
In case of the image failure after connecting camera, or video loss due to changes in the menu,
it is possible to restore the factory settings. Following procedure is also recommended when
camera menu is not working. To restore factory settings:
1. Turn the power off and on again.
2. If the picture does not appear, perform the following sequence of joystick keys:
press ENTER, UP, RIGHT, press ENTER.
Successful completing these steps restores factory settings (AHD 720p, PAL).
video
12V DC +/- 10% power supply
video
(GND)
+
- (GND)

NVAHD-1DN3102H/IR-1 - ver. 1.0 - User’s manual
All rights reserved © AAT Holding S.A.
10
SETTINGS
5.1. Main menu
In order to enter the menu press the joystick button (ENTER command). The following menu is
displayed on the screen:
5.1.1 LENS submenu
This submenu allows to set lens parameters:
MANUAL - manual iris lens or fixed iris lens
DC - auto iris mode (DC signal control) - opens another sub-menu.
MODE - selects the operating inside mode (INDOOR) or outside mode (OUTDOOR)
IRIS SPEED - sets the shutter speed (0 to 15).
OUTDOOR mode opens another sub-menu where you can set the minimum and maximum
aperture.
5.1.2 EXPOSURE submenu
This submenu contains exposure and shutter speed settings.

NVAHD-1DN3102H/IR-1- ver. 1.0 - User’s manual
All rights reserved © AAT Holding S.A.
11
SETTINGS
SHUTTER - shutter mode control. Allows you to choose the automatic mode (AUTO), the manual
mode with adjustable shutter speed in the range of 1/25 ~ 1/50000s and ability to enable the
DSS function in the range from x2 to x30, and flicker reduction (FLK).
AGC - Sets AGC gain. Higher gain make a scene brighter, but noise increases. It allows to
adjust the gain in the range from 0 to 15.
SENSUP - Digital Slow Shutter function - helps to obtain better, brighter images in low light by
selecting the multiplier of shutter speed in the range from x2 to x30 (opens another sub-menu).
BRIGHTNESS - sets brightness level in the range from 1 to 100.
D-WDR - this function allows to enable/disable wide dynamic range function that enables to
observe the scene with different illumination levels. After selecting this function, there is
a submenu to adjust the level in the range from 0 to 8.
DEFOG - allows you to enable correction functions of image disrupted by the influence of fog,
rain, etc. It opens another sub-menu that allows you to set the zone and the degree of noise
reduction.
5.1.3 BACKLIGHT submenu
These compensation functions allow to enhance visibility of the objects located in the
foreground, surrounded by strongly illuminated background (BLC) or for enhancing visibility of
the objects located near the strong light source (HSBLC).
BLC - function allows to enhance visibility of the objects located in the foreground, surrounded
by strongly illuminated background. Pressing ENTER button in this mode displays the following
menu:
Submenu presented allows to set the size and location of the area where the BLC function is
active, furthermore it allows to set the sensitivity of the function.
HSBLC - high light compensation function. It allows to enhance visibility of the objects located
near the strong, point light source. If a strong, point light source appears on the screen , function
will mask it for effective observation of the scene itself (this function is recommended e.g. to
observe car licence plates). Selecting HSBLC displays following screen:

NVAHD-1DN3102H/IR-1 - ver. 1.0 - User’s manual
All rights reserved © AAT Holding S.A.
12
SETTINGS
SELECT - allows to select one of the four areas of HSBLC function
DISPLAY - enables or disables previously selected zone.
BLACK MASK - enables or disables masking area
LEVEL - adjusts intensity function between 0-100
MODE - (ALL DAY/NIGHT) determines whether the function is running all the time or only at
night (recommended).
DEFAULT - restores default HSBLC settings.
5.1.4 WHITE BAL submenu
This feature allows to set appropriate color settings using following options:
ATW - auto tracking white balance based on color temperature.
AWC→SET - this mode enables adaptive setting of white balance. In order to obtain the
optimum state under the current illumination, direct the camera at a sheet of white paper and
press ENTER. When lighting parameters change (e.g. light bulbs changed to halogen lamps,
daylight to artificial light etc. ), procedure mentioned above should be repeated;
AWB - auto white balance adjustment.
MANUAL - manual mode settings. In case of inappropriate color settings for ATW, AWC
modes it is possible to set RED and BLUE values manually. Color values range from 0 to 100
and are represented by sliders. Any change in the color components are instantly applied to the
image.
5.1.5 D&N submenu
Allows to adjust day/night settings. Available settings are: AUTO, EXT, COLOR, B/W.
AUTO - camera switches between night (b/w) and day (color) mode automatically, depending
on current illumination conditions. Settings are available at following sub-menu:
D--N (CDS) and N--D (CDS) - sets the illumination threshold that switches the camera from day
to night mode and from night to day mode (respectively 6~255 and 0~249)
D--N (DELAY) and N--D (DELAY) - sets the delay between color and b/w mode switching and
between b/w and color mode (0~60s)

NVAHD-1DN3102H/IR-1- ver. 1.0 - User’s manual
All rights reserved © AAT Holding S.A.
13
SETTINGS
B/W - forces continuous black & white mode. Selecting displays following submenu for
adjusting additional values:
BURST - enables/disable chrominance signal synchronization.
IR SMART - function ensuring balanced brightness level of the picture during operation with an
IR illuminator (which prevents overexposure of the objects located close to the camera and its
illuminator). Entering the function allows to set function area and sensitivity, in the same
manner as in motion detection menu.
IR PWM - unavailable
5.1.6 NR submenu
Allows to make settings for digital noise reduction function. Pressing ENTER button in this
mode displays the following menu:
2DNR - allows to set the level of noise reduction for static parts of the image (available
settings: OFF, LOW, MIDDLE, HIGH)
3DNR - allows to set the level of noise reduction variables (dynamic) parts of the image
(available settings: OFF, LOW, MIDDLE, HIGH)
NOTE:
In the 960H analog mode only 2DNR noise reduction is available.
5.1.7 SPECIAL submenu
Allows to set additional camera features. Pressing ENTER button in this mode displays the
following menu:

NVAHD-1DN3102H/IR-1 - ver. 1.0 - User’s manual
All rights reserved © AAT Holding S.A.
14
SETTINGS
CAM TITLE - allows to enter a string of characters that will be displayed on the screen, e.g. as
camera title. Screen contains mainly alphanumerical characters, which may be used in
camera’s title. Select desired character and press ENTER key. Currently edited title is visible at
the bottom of the screen. Line above it contains buttons for editing the title. To enable
particular functions, please highlight them as normal characters and confirm by pressing
ENTER. Button functions are described below:
  - moves character highlight cursor left.
  - moves character highlight cursor right.
POS - adjusts the position of entered characters.
CLR - erases the whole title.
END - exits title editing menu.
D-EFFECT - submenu allows to set additional digital functions:
FREEZE - holds the picture currently displayed.
MIRROR - allows to change viewpoint as MIRROR, ROTATE, V-FLIP.
NEG. IMAGE - enables/disables displaying negative video image.
MOTION - allows (provided that ON option is selected) to turn a built-in motion detection
feature on or off. Motion detection may simultaneously be conducted in four independent zones
(with their size and location selectable by user). Detection of motion displays an „MOTION
DETECTED” information superimposed on the screen.
After selecting ON and pressing ENTER adjust motion detection settings is displayed, as
depicted below:
SELECT - selects the number of the area for further settings.
DISPLAY - turns on/off particular area. Also allows to set the position and size of the area.
SENSITIVITY - refers to sensitivity
COLOR - sets the color visualization of motion in a particular area
TRANS - allows to set the transparency level of visualization
ALARM - displays submenu where user can set motion visualization mode (OFF, BLOCK,
OUTLINE, ALL), enable or disable displaying „MOTION DETECTED” information and set its
display time (1 ~ 15 s). Options ALARM OUT and ALARM SIG are inactive.
DEFAULT - restores default settings.

NVAHD-1DN3102H/IR-1- ver. 1.0 - User’s manual
All rights reserved © AAT Holding S.A.
15
SETTINGS
PRIVACY - allows to enable (by selecting ON) privacy zones. Part of the screen may be
masked using four rectangular zones. Selecting ON and pressing ENTER displays a sub-
menu, containing four masks positions.
SELECT - selects the number of the area for further settings.
DISPLAY - turns on/off particular area. Available masking methods: with overlaid color, color
reversal or tessellation (COLOR, INV, MOSAIC). Pressing ENTER after selecting COLOR, INV or
MOSAIC option will open a new submenu which allows to set the position and size of the
zone.
COLOR - sets the color masking (available only if COLOR option was chosen).
TRANS - allows you to set the degree of transparency mask (available only if COLOR option
was chosen).
DEFAULT - restores default settings.
LANGUAGE - switches between OSD languages: Polish, English, Russian and others.
DEFECT - allows to adjust parameters used in Dead Pixel Correction function:
LIVE DPC - sets parameters of the defective pixel correction function in real time. Selecting
ON and pressing ENTER button opens a submenu for setting the gain level and the level of
correction.
WHITE DPC - allows to a correct "hot pixels". Selecting ON and pressing ENTER button opens
a submenu where you can specify the size and location of the zone in which the correction
will be made (position POS/SIZE), then define the level of correction and amplification (LEVEL
and AGC positions) and set SENS-UP option (if camera uses SENS-UP position). Then select
START position and press ENTER, cover the lens tightly and press ENTER again. After
correcting process the camera returns to the DPC WHITE menu. In the DPC VIEW you can
check the correction effect and, if needed repeat the operation with different settings.

NVAHD-1DN3102H/IR-1 - ver. 1.0 - User’s manual
All rights reserved © AAT Holding S.A.
16
SETTINGS
BLACK DPC - allows to correct (mask) dead pixels. Selecting ON and pressing ENTER button
opens a submenu which define the size and location of the zone in which the correction is made
(position POS/SIZE), then define the compensation level (position LEVEL). Then select START
position and press ENTER button and wait for the end of the operation. In the DPC VIEW check
the correction effect and, if needed repeat the operation with different settings.
RS485 - option disabled
5.1.8 ADJUST submenu
It allows to perform additional image adjustment. After pressing ENTER, the following submenu
is dispalyed:
SHARPNESS - allows to disable (OFF) and enable (AUTO) sharpness correction function. After
selecting AUTO and pressing ENTER, next submenu is displayed, where it is possible to set the
degree of correction and gain ranges for compensation
MONITOR - corrects the image parameters depending on chosen monitor (LCD monitor or CRT
monitor). After pressing ENTER, the submenu is displayed where fine adjustments can be made.
LSC - enables and disables the function of increasing the brightness of the image edge
VIDEO OUT - chooses a system in which the camera works (PAL or NTSC)
INFORMATION:
For camera mode analog 960H in the ADJUST menu there are two additional items:
MONITOR OUT - switches the aspect ratio between 4:3 and 16:9
COMET - option disabled

NVAHD-1DN3102H/IR-1- ver. 1.0 - User’s manual
All rights reserved © AAT Holding S.A.
17
NOTES

AAT Holding S.A.
ul. Puławska 431, 02-801 Warszawa
tel.: [phone], fax: [phone]
www.novuscctv.com
2015-06-17 MF, TF

NVAHD-1DN3102H/IR-1
ins t r u k c j a obs ł u g i

NVAHD-1DN3102H/IR-1 - instrukcja obsługi wersja 1.0
Wszelkie prawa zastrzeżone © AAT Holding S.A.
2
INFORMACJE
Dyrektywy EMC (2004/108/EC) i LVD (2006/95/EC)
Oznakowanie CE
Nasze produkty spełniają wymagania zawarte w dyrektywach oraz przepisach krajowych
wprowadzających dyrektywy:
- Kompatybilność elektromagnetyczna EMC 2004/108/EC.
- Niskonapięciowa LVD 2006/95/EC. Dyrektywa ma zastosowanie do sprzętu elektrycznego
przeznaczonego do użytkowania przy napięciu nominalnym od 50VAC do 1000VAC oraz od 75VDC do
1500VDC.
Dyrektywa WEEE 2002/96/EC
Informacja dla użytkowników o pozbywaniu się urządzeń elektrycznych i elektronicznych
Niniejszy produkt został oznakowany zgodnie z Dyrektywą WEEE (2002/96/EC) oraz
późniejszymi zmianami, dotyczącą zużytego sprzętu elektrycznego i elektronicznego.
Zapewniając prawidłowe złomowanie przyczyniają się Państwo do ograniczenia ryzyka
wystąpienia negatywnego wpływu produktu na środowisko i zdrowie ludzi, które mogłoby
zaistnieć w przypadku niewłaściwej utylizacji urządzenia.
Symbol umieszczony na produkcie lub dołączonych do niego dokumentach oznacza,
że nasz produkt nie jest klasyfikowany jako odpad z gospodarstwa domowego. Urządzenie należy oddać
do odpowiedniego punktu utylizacji odpadów w celu recyklingu. Aby uzyskać dodatkowe informacje
dotyczące recyklingu niniejszego produktu należy skontaktować się z przedstawicielem władz lokalnych,
dostawcą usług utylizacji odpadów lub sklepem, gdzie nabyto produkt.
Dyrektywa RoHS 2002/95/EC
Informacja dla użytkowników dotycząca ograniczenia użycia substancji niebezpiecznych w sprzęcie
elektrycznym i elektronicznym.
W trosce o ochronę zdrowia ludzi oraz przyjazne środowisko zapewniamy, że nasze produkty
podlegające przepisom dyrektywy RoHS, dotyczącej użycia substancji niebezpiecznych
w sprzęcie elektrycznym i elektronicznym, zostały zaprojektowane i wyprodukowane zgodnie
z wymaganiami tej dyrektywy. Jednocześnie zapewniamy, że nasze produkty zostały
przetestowane i nie zawierają substancji niebezpiecznych w ilościach mogących niekorzystnie
wpływać na zdrowie człowieka lub środowisko naturalne.
Informacja
Urządzenie, jako element profesjonalnego systemu telewizji dozorowej służącego do nadzoru i kontroli,
nie jest przeznaczone do samodzielnego montażu w gospodarstwach domowych przez osoby nie
posiadające specjalistycznej wiedzy.
Obowiązek konsultowania się z Producentem przed wykonaniem czynności nieprzewidzianej
instrukcją obsługi albo innymi dokumentami:
Przed wykonaniem czynności, która nie jest przewidziana dla danego Produktu w instrukcji obsługi,
innych dokumentach dołączonych do Produktu lub nie wynika ze zwykłego przeznaczenia Produktu,
należy, pod rygorem wyłączenia odpowiedzialności Producenta za następstwa takiej czynności,
skontaktować się
z Producentem.