Installation / Operation / Maintenance
Ionmaster®Ionizing Fan (with heater)
Model 6214
NRD, LLC / 2937 Alt Boulevard / Grand Island, NY 14072
PHONE 716 773 7634 / FAX 716 773 7744 / EMAIL sales@nrdllc.com / WEB www.nrdllc.com
NRD Asia Pte. Ltd
PHONE +65 6679 1707 / EMAIL sales@NRDasia.com / WEB www.nrdllc.com
INST6214 – 1/23
Locate the Ionmaster®M/N:6214:
•12” to 48” from the target to be neutralized for
optimal performance, making sure that the airflow
will not be restricted.
•A working electrical outlet within reach of the 6
detachable cord that is supplied with the Ionmaster®
M/N:6214.
The Ionmaster®M/N:6214 can be installed in two dif-
ferent ways:
•Placed or secured on a flat surface such as a bench
top
. The unit comes with a stand so that it can be po-
sitioned on the work surface, aimed at the target and
adjusted for inclination and locked in place with the
lock knobs.
•It can also be wall or shelf mounted to keep valuable
bench space free for other purposes and equipment.
Connect the barrel plug of the AC adapter to the re-
ceptacle in the back of the Iommaster®M/N:6214.
Connect the AC adapter to a 1
outlet which is properly grounded. Ensure the unit
Power Switch is in the off position before plugging in.
Important Note: Before powering up the ionizer,
verify that the AC outlet is properly grounded and
that the supplied line voltage matches the electrical
specifications on the rear panel of the unit. Plugging
the ionizer into an outlet with the incorrect voltage
may damage the unit and will void any warranty
coverage.
To turn the ionizer ON press the red POWER switch,
located on the lower right front panel of the unit. The
POWER switch will illuminate when the ionizer is run-
ning.
To change the ionizer speed, use the FAN switch to se-
lect HI or LOW fan speed located next to the POWER
switch.
Adjust the ionizer to direct the airflow into the work
area.
If heating is desired for operator comfort this can be
turned on by turning the HEATER switch to the ON
position. Heater can be used in HI or LOW fan speed.
There are no user serviceable parts INSIDE this
ionizer. DO NOT remove front panel, or back
chrome finger guard.
Under normal operating conditions the ionizer will at-
tract dirt and dust, especially on the emitter pins, and
filter. To maintain optimum neutralization efficiency
and operation, cleaning should be performed on a reg-
ular basis.
Emitter Point Cleaning:
1. To clean the emitter points rotate the cleaning brush
clockwise and allow spring to return brush counter-
clockwise. Knob is located on the front of the ionizer
and labeled Point Cleaner.
2. Repeat step 1 several times for sufficient cleaning of
emitter points.
Filter Cleaning:
1. If foam filter on back of ionizer becomes dirty,
carefully unsnap white plastic retainer ring holding the
foam in place.
2. Clean foam filter with soap and water. Allow filter to
dry completely before re-installing.
3. Push filter into white pla
stic retainer ring and snap onto
chrome finger guard…be sure to line up cutouts and
push until it snaps in place.
Fuse Replacement:
1. In the event that the power input fuse blows and needs
replacing. UNPLUG THE UNIT PRIOR TO
REPLACING FUSE
2. Remove the power cable from the back of the ionizer
3. Using a small screwdriver pry open the fuse drawer lo-
cated below the power cable input jack. Carefully
remove the fuse drawer and fuse replace with
Fuse type: GMA 5A 250V
(20mm length x 5mm diameter)
4. Re-install fuse drawer and snap
fuse into place. Check ionizer
for proper operation.
