NuPrime Omnia S1 User manual

Omnia S1 is purpose-built audio equipment that optimizes
as a DLNA Server and Renderer. It has the added benefit
of running native Android streaming apps.
Omnia S1
USER’S MANUAL

1
www.nuprimeaudio.com
Table of Contents
FCC Notice - Declaration of Conformity Information .................................................................................. 2
EU Declaration of Conformity .................................................................................................................... 3
For customers in Europe ............................................................................................................................ 3
SAFETY INSTRUCTIONS ........................................................................................................................... 4
Safe Use and Operation of Your Device ..................................................................................................... 4
Introduction ............................................................................................................................................... 7
Setting up the Omnia ............................................................................................................................... 10
Admin Settings Web Page ....................................................................................................................... 13
Apps & Firmware Update ......................................................................................................................... 17
Using the Omnia S1 as Music Server ........................................................................................................ 20
Using the Omnia S1 as Music Renderer .................................................................................................... 20
Using the Streaming Apps ....................................................................................................................... 20
NuPrime’s Limited Warranty and Limitation of Liabilities ........................................................................ 21

2
www.nuprimeaudio.com
FCC Notice - Declaration of Conformity Information
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: Only peripherals complying with the FCC class B limits may be attached to this equipment.
Changes or modifications made to this equipment, not expressly approved by us or parties authorized by
us could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC
Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.

3
www.nuprimeaudio.com
EU Declaration of Conformity
Hereby, NuPrime Audio, Inc. declares that this device is in compliance with the essential
requirements and other relevant provisions of Directive 2004/108/EC.
The manufacturer of this product is NuPrime Audio, Inc., 1712 Pioneer Ave. Ste 1817, Cheyenne, Wyoming
82001, USA.
The Authorized Representative for EMC and product safety is NuPrime Audio, Inc., 1712 Pioneer Ave. Ste
1817, Cheyenne, Wyoming 82001, USA.
For any service or guarantee matters please refer to the addresses given in separate service or guarantee
documents.
For customers in Europe
Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and
other European countries with separate collection systems)
This symbol on the product or on its packaging indicates that this product shall not be
treated as household waste. Instead it shall be handed over to the applicable collection
point for the recycling of electrical and electronic equipment. By ensuring this product is
disposed of correctly, you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by inappropriate waste
handling of this product. The recycling of materials will help to conserve natural resources.
For more detailed information about recycling of this product, please contact your local Civic Office, your
household waste disposal service or the shop where you purchased the product.

4
www.nuprimeaudio.com
SAFETY INSTRUCTIONS
There are two categories of Safety Instructions included in this manual:
• Product Warnings, (i.e., what must never be done to assure avoiding those hazards that
• could cause bodily injury or property damage); and
• User Directions (i.e., what must always be done to assure the safe use of your device).
The Safety Instructions contained in this manual have been categorized in accordance with the seriousness
of the potential hazards through the use of Signal Words. Those Signal Words, and their intended
meanings, are as follows:
DANGER: Indicates that a failure to observe the Safety Instructions could result in death or catastrophic
bodily injury.
WARNING: Indicates that a failure to observe the Safety Instructions could result in serious bodily injury.
CAUTION: Indicates that a failure to observe the Safety Instructions could result in minor bodily injury or
property damage.
NOTE: Designates important information that relates to activities and/or conditions that might result in
loss of data and/or damage to your device.
Safe Use and Operation of Your Device
This equipment emits stray RF energy and will interfere with the reception of signals by airborne electronic
navigational devices or medical devices. Do not operate this equipment near any sensitive medical devices.
WARNING: Use only grounded AC power cords.
Always immediately disconnect the power to the equipment in the event the device emits an unusual
odor or sound or generates smoke.

5
www.nuprimeaudio.com
WARNING: Never attempt to disassemble, repair or make any modi cation to your device. Disassembly,
modi cation or any attempt at repair could cause bodily injury or property damage, as well as damage to
the device itself.
WARNING: Your device is not a toy. Never allow children to play with your device. Misuse, rough or
improper handling of your device by children could result in serious bodily injury for any of the enumerated
safety warnings in this manual. In addition, always keep all accessories and components out of the reach of
small children as small parts might present a choking hazard. Seek immediate medical attention if choking
occurs or if any small part has been swallowed.
CAUTION: Never raise the sound volume level too high when using your device with earphones. An
excessive sound volume level could cause damage to your hearing.
WARNING: To reduce the risk of re or electric shock, do not expose the unit to moisture or water.
Do not allow foreign objects to get into the enclosure. If the unit is exposed to moisture, or a foreign object
gets into the enclosure, immediately disconnect the power cord from the wall. Take the unit to a qualified
service person for inspection and necessary repairs.
Read all the instructions before connecting or operating the component.
Keep this manual so you can refer to these safety instructions.
Heed all warnings and safety information in these instructions and on the product itself. Follow all
operating instructions.
Do not use this unit near water.
You must allow a minimum 10 cm or 4 inches of unobstructed clearance around the unit.
Do not place the unit on a bed, sofa, rug, or similar surface that could block the ventilation openings. If the
unit is placed in a bookcase or cabinet, there must be ventilation of the cabinet to allow proper cooling.
Keep the component away from radiators, heat registers, stoves, or any other appliance that produces
heat.
The unit must be connected to a power supply only of the type and voltage speci ed on the rear panel.
Connect the component to the power outlet only with the supplied power supply cable or an exact
equivalent. Do not modify the supplied cable.

6
www.nuprimeaudio.com
Do not route the power cord where it will be crushed, pinched, bent, exposed to heat, or damaged in any
way. Pay particular attention to the power cord at the plug and where the cord exits the back of the unit.
The power cord should be unplugged from the wall outlet during a lightning storm or if the unit is to be left
unused for a long period of time.
Immediately stop using the component and have it inspected and/or serviced by a quali ed service agency
if:
• The power supply cord or plug has been damaged.
• Objects have fallen or liquid has been spilled into the unit.
• The unit has been exposed to rain.
• The unit shows signs of improper operation.
• The unit has been dropped or damaged in any way

7
www.nuprimeaudio.com
Introduction
The Omnia S1 is a purpose-built audio equipment that performs both as a Server and a Renderer for your
Digital Audio collection. The Server and Renderer are both DLNA/UPnP compatible, therefore allowing
the flexibility of streaming music stored on the Omnia S1 to other DLNA/UPnP compatible renderers; and
also streaming music from other DLNA/UPnP compatible servers to the Omnia S1. You can choose to use
any DLNA/UPnP compatible controller software (e.g. Bubble UPnP) with the Omnia.
The firmware used for the Omnia S1 is based on Google’s Android operating system. A custom audio
driver and hardware were developed which are used by the Renderer to send bit-perfect digital audio via
the digital outputs. It also allows Hi-Res PCM audio, DSD(DoP) and I2S playback through a compatible
DAC.
Hardware Features:
1. The ARM CPU and firmware handle 32-bit/768kHz and DSD1024 decoding of any available music
format.
2. Audio Processing Decoupled from CPU: To isolate the audio processing from performance
degradation due to high CPU utilization or signal drop-off due to
wireless congestion, the Omnia Audio Processor Unit (OAP
Unit) operates independently from the CPU and provides
caching of digital music and completely eliminates jitter.
Being a digital transport without the moving parts of a disc based system, the performance of the Omnia
S1 surpasses most CD transports. The dedicated firmware designed for low latency playback enables a
superior quality compared to typical PC or ARM based offerings.

8
www.nuprimeaudio.com
Specifications
Refer to the above illustration from left to right:
• AC socket
• USB 3.0 port for hard disk and system upgrade use
• Coaxial output (PCM up to 192kHz and DoP format DSD64)
• Optical output (PCM up to 192kHz and DoP format DSD64)
• I2S output (PCM 32K to 768K, DSD64 to DSD1024)
• HDMI display output (video only)
• 4 X USB 2.0 ports for mouse, keyboard, WiFi dongle, and hard disk.
• RJ45 ethernet port
• Hardware reset button

9
www.nuprimeaudio.com
I2S port specification:
Supported Audio Formats
File Types
AAC, AIFF, ALAC, APE, DSF, DXD, FLAC, MP3, OGG, WAV, WMA
Bitrates
16bits, 24bits, 32bits
Sample Rates
PCM: 44.1, 48, 88.2, 96, 176.4, 192, 352.8, 384 KHz
DSD: 2.8MHz (optical and coaxial outputs), 45.2MHz (I2S)

10
www.nuprimeaudio.com
Setting up the Omnia
The Omnia S1 can be connected to your network either by using a wired connection (Ethernet) or using
the supplied USB dongle for a wireless connection.
Wired Connection (Ethernet)
Connect the Omnia S1 to your network router using a LAN cable. By default, the Omnia will obtain an IP
Address from your router via DHCP automatically. Power on the Omnia S1 via the rear switch and both
the Omnia Server and Renderer should be visible under your network devices after a few minutes.
Wireless Connection
Note: A HDMI display and USB mouse is required for performing this setup.
Insert the supplied USB dongle into one of the available USB port on the rear panel of the Omnia S1.
Connect the USB mouse to another one of the available USB port. Connect the display to the Omnia S1
via the HDMI video port. Power on the Omnia S1 and wait till the first time initialization completes (the
unit may restart automatically during the initialization). The setting icon is located at the bottom row on
the home screen. Click on the setting icon which will bring you to the settings page. Click on WIFI which
will bring to the WIFI settings page. The on/off toggle for the WIFI is located at the top right of the screen.

11
www.nuprimeaudio.com
Toggle it to ‘ON’ and the system will start scanning for available WIFI networks. Select the network from
the list that you wish to connect to. For secured networks, you will be asked for the password. Enter the
password using the onscreen keyboard (or optionally a USB keyboard connected to the Omnia S1) and the
Omnia S1 should be connected to your wireless network.

12
www.nuprimeaudio.com
*Note that the Omnia S1 will take some time to perform a first time initialization. The boot up time will
significantly reduce for subsequent power on.

13
www.nuprimeaudio.com
Admin Settings Web Page
Local Access
If you have a display, mouse and keyboard connected to the Omnia, you can access the Admin Settings
page by clicking on the ‘Red Ribbon’ icon on the home screen.
Remote Access
The Admin Settings Web Page can be accessed by any web browser that is on the same network as the
Omnia S1. You will require the IP Address of the Omnia S1 on your network to enter into your browser’s

14
www.nuprimeaudio.com
URL bar. Below is an example identifying the IP Address and accessing the Admin Settings Web Page with
a Windows PC.
The settings on this page allows you to perform the admin functions for the Omnia.

15
www.nuprimeaudio.com
Server Name – Shows the current name of the Omnia Server that will appear in your UPnP
browser/controller.
Renderer Name – Shows the current name of the Omnia Renderer that will appear in your UPnP
browser/controller.
New Server Name – Change the name of the Omnia Server that appears in your UPnP browser/controller.
To change, type in the new name in the text box and click on the ‘Change Server Name’ button.

16
www.nuprimeaudio.com
New Renderer Name – Change the name of the Omnia Server that appears in your UPnP
browser/controller. To change, type in the new name in the text box and click on the ‘Change Server
Name’ button.
Restart DLNA Services – Click on the button to restart the Server and Renderer (if they become
unresponsive to the controller).
Rescan Media and restart SERVER – Click on the button to rescan your music library (when new music is
added to the attached storage devices) and restart the Server.
Reset Server Database – Click on the button to reset the Server database (if the indexing of the audio
files becomes corrupted i.e. showing wrong track info).
Check Update – Click on the button to check if a newer version of the application package is available
online. If a newer version is available, the system will automatically download the package and restart the
unit to perform the update (requires internet connectivity).
Power Off/Reset Omnia – Click on the button to power off (recommended especially if a mechanical hard
drive is connected before turning off via the main switch) or reboot the unit.

17
www.nuprimeaudio.com
Apps & Firmware Update
Omnia S1 is a customized Android OS and hardware. Therefore, users are not permitted to install any App
unless it is tested and released by NuPrime. Whenever an existing App has a new version or a new App is
introduced, it will be uploaded to NuPrime website for the Check Update function to perform a series of
steps to install the App.
When updating the applications using the Check Update function, please do not close the browser
window as that will terminate the update. The progress of the update can be monitored in the browser
window in case of any errors.
After the application package has been downloaded and while the apps are installing, you may see the
below screen:

18
www.nuprimeaudio.com
Click on ACCEPT to continue the installation. To prevent such prompts in the future, bring up the apps
menu by clicking the icon on home screen and then click on Google Settings. Click on Security and
then Google Play Protect.
Turn off Scan device for security threats as shown in the screenshot below which will disable such
prompts.

19
www.nuprimeaudio.com
Omnia S1 Firmware Update
In the rare event that Omnia S1 operating system and firmware have to be updated, please visit the
Omnia S1 product page download tab on NuPrimeAudio.com
Table of contents
Popular Server manuals by other brands

FOR-A
FOR-A MBP-100PD Series Operation manual

Multitech
Multitech ProxyServer MTPSR1-100 installation manual

3One data
3One data NP301 Quick installation manual

Blackbe;rry
Blackbe;rry ENTERPRISE SERVER FOR NOVELL GROUPWISE - - MAINTENANCE RELEASE... release note

Watchguard
Watchguard Firebox M470 Hardware guide

Black Box
Black Box LE2101A-BT-R2 manual