Nuvico Xcel NCT-5MLC-E2 User manual

Package
Overview
Installation
1
2
3
4
Warning and Caution
■If the product does not work properly, please contact your dealer or the
nearest service center. Never attempt to disassemble the camera yourself.
(We shall not be responsible for any problems caused by unauthorized
repair or maintenance.)
■Do not allow water or liquid intrusion into the camera.
■In the use of the product, you must be strict compliance with the
electrical safety regulations of the nation and region. When the product is
mounted on wall or ceiling, the device shall be firmly fixed.
■Do not use camera beyond specified voltage range.
■Do not drop the camera or subject it to physical shock.
■The product must be grounded to reduce the risk of electric shock.
■ Avoid touching the camera lens.
■If cleaning is necessary, please use clean cloth to wipe it gently.
■Avoid pointing the camera towards the sun or other light sources.
■Do not place the camera in extremely hot, cold (the operating
temperature shall be -22˚F~140˚F), dusty or damp locations, and do not
expose it to high electromagnetic radiation.
■To avoid heat accumulation, good ventilation is required for operating
environment.
NCT-5MLC-E2 Eyeball Camera
Quick Start Guide Camera Quick start guide
Plastic plug ×3
Drill template Allen key
Tapping screws × 3
■Please read these instructions carefully before operating the unit
and keep it for further reference.
■All the examples and pictures used here are for reference only.
■The contents of this manual are subject to change without notice.
■Visit nuvico.com for additional downloads, manuals, and resources.
* 1 It is recommended to install the security cap for outdoor installation.
* 2 If the PoE switch is used to power the camera, DC12V power supply is not
required.
Security Cap
Ethernet connector
Micro SD card slot
Power connector
Audio input
Reset
15
26
37
8
4
Fixed screw
Mounting base
Fixed Screw
Mounting Base
Enclosure
Dome
Microphone
Before you start, please make sure that the wall or ceiling is strong
enough to withstand three times the weight of the camera. Please
install the camera in a dry environment.
①Loosen the fixed screw to disassemble the camera.
②Unscrew the cover of the dome and then insert a micro SD card.
After that, install back the cover and make sure the cover is installed
firmly.
Insert a micro SD card
Cover
③Drill the screw holes and the cable hole on the ceiling according
to the drill template. Then route and connect the cables.
Earth wire connection
(mm)
Ø91.9
Ø63.8
Ø4.5
1
2
3
4
5
6
7
8
DC12V

Network Connection
5
MENU
IPC
Network Cable Network Cable
Switch
Router Computer
●Access Through Xcel IP Utility
①Make sure that the camera and the PC are connected to the local
network.
②Download and install Xcel IP Utility from nuvico.com and run it
after installation.
Device Network Search
Immediate Refresh
Nuvico Xcel
Nuvico Xcel
Nuvico Xcel
IPC
IPC
IPC
NCT-8ML2-E2
NCT-5MLC-B2
NCT-5ML-OV2
192.168.226.201
192.168.1.2
192.168.1.3
80
80
80
9008
9008
9008
255.255.
255.255.
255.255.
Modify Network Parameter
Mac Address
IP Address
Modify
CE :98 :23 :75 :35 :22
192 . 168 . 226 . 201
255 . 255 . 255 . 0
192 . 168 . 226 . 1
i
Tip: Enter the administrator password, and
then modify the network parameters.
Total Device: 3 Local IP Address:192.168.1.4Subnet Mask:255.255.2 55.0 Gateway: 192.168.1.1 DNS：210.21.196.6
Device Name Device Type IP Address Http Port Data Port Subnet Product Model
About
Subnet Mask
Gateway
Restore IPC Default Configuration
⑤Install the dome and enclosure to the mounting base.
(a) (b) ( )
c
(a). Loosen the nut from the main element.
(b). Run the network cable (without RJ45 connector) through the
both elements. Then crimp the cable with RJ45 connector.
(c). Connect the cable to the hermetic connector. Then tighten the nut and
the main cover.
④Secure the mounting base to the ceiling or wall with the screws provided.
Then adjust the dome to obtain an optimum view angle.
0 ~75° °
0 ~360° °
0 ~360° °
⑥Finally, fix the camera with the fixed screw.
Fixed screw
③Double click the camera information listed in Xcel IP Utility to
open the web browser. You can also type the default IP address in the
address bar of your browser and press enter.
The default IP address of this camera is 192.168.226.201.
Then follow directions to download and install the plugin if it is the
first time for you to log in.
④Activate and log in the camera. The default username is admin; the
default password is 123456 or you need to self-define the password.
Please operate according to the actual situation.