2www.observint.com
WARNING
!
Drop cable connectors are not waterproof. Failure of the power or video connector
due to moisture or another contaminant is considered an installation error,
which voids the warranty. If installing this camera in a location such as an
overhang, shop, garage, kitchen, etc. where high humidity or dust is present,
seal these connections adequately.
7. Connect the other end of the power extension cable to a 12 Vdc power source. Observe the polarity
of the cable shown in the photo on page 1 of this guide.
• Mounting the camera with a junction box
The optional junction box is shown below. It can be attached to a wall or ceiling. Video and power
extension cables can be routed in through the opening in the back of the box or through the conduit
coupling, and attached to the camera drop cables inside the enclosure.
Front
Front
plate
Box
Conduit
coupling/
cable
channel
Back
“UP”
label
Holes for
mounting
screws (3) Holes for
mounting
base
screws (6)
To use the junction box:
1. Remove the front plate from the box by removing the three screws (see above).
2. Attach the front plate to the camera mounting base using three screws. If the box will be wall
attached to a wall, ensure that the “UP” label on the mounting plate is at the top of the camera, and
the cable channel in the camera mounting base is toward the bottom of the camera.
3. Using the junction box as a guide, mark and then drill three holes for the screws that will attach the
box to the wall or ceiling. If the extension cables will be routed into the box through the mounting
surface, also drill a hole for the extension cables.
4. Attach the box to a wall or ceiling with three screws. Ensure that the wall or ceiling will support at
least three times the weight of the camera with the junction box.
5. Route the video and power extension cables into the box.
6. Attach the video and power extension cable to the camera drop cables. Observe the polarity of the
power cable connector as shown on page 1 of this guide.
WARNING
!
Drop cable connectors are not waterproof. Failure of the power or video connector
due to moisture or another contaminant is considered an installation error,
which voids the warranty. If installing this camera in a location such as an
overhang, shop, garage, kitchen, etc. where high humidity or dust is present,
seal these connections adequately.
7. Re-attach the front plate (with the camera) to the box.
Camera adjustments
1. Apply power to the camera.
2. Verify that video from the camera can be seen on the monitor.
3. While observing video from the camera, loosen the mounting bracket pan lock screw, and tilt and
rotation adjustment lock screws, point the camera at your surveillance target, and then tighten
adjustment lock screws to hold the camera in position.
0° ~ 90°
0° ~ 360°
0° ~ 360°
Rotation: Use for horizon
line adjustment
Pan: Use
for pan
adjustment
Tilt: Use for
elevation
adjustment
Mounting bracket adjustment
Camera conguration customization
For conguration and customization, refer to the User Manual for your camera or recorder.
Specications
Camera Model (SKU). B5
Image Sensor 1/2.7” CMOS
Resolution 5MP: 2592 (H) × 1944 (V)
Video Output Termination 1-channel BNC video output
Minimum Illumination 0.05 lux @ F1.0 (AGC ON)
0 lux with IR ON
IR Cut Filter Yes, 850 nm
DWDR Yes
WDR N/A
IR LEDs 18
Night Vision (IR range) 65 ft (20 m)
Lens 2.8 mm
Viewing Angle (degrees) Horizontal FOV: 102.94°
Backlight Compensation OFF (default)
Mechanical Zoom Fixed-focus
Audio - Microphone No
Audio Range (Mtrs) N/A
On-screen display (OSD) Yes
Operating Power 4 W max.
Operating Temperature -22° ~ +131°F (-30° ~ +55° C)
Number of PIRs (Motion Detection) 1
PIR Detection Angle 120°
PIR Detection Distance 23 ft (7 m)
Cleaning
Clean the camera dome with an approved glass cleaning solution and a lint free cloth.
• Dust can be removed from the unit by wiping it with a soft damp cloth. To remove stains, gently rub
the surface with a soft cloth moistened with a mild detergent solution, then rinse and dry it with a
soft cloth. Do not use benzene, thinner or other chemical products on the camera assembly; these
may dissolve the paint and promote damage of the surfaces.
• Remove all foreign particles, such as plastic or rubber materials, attached to the camera housing.
These may cause damage to the surface over time.
© 2018 Observint Technologies. All rights reserved.
