WARNING! Ensure the air supply is clean and does not exceed 90 psi while
operating the wrench. Too high an air pressure and/or unclean air will shorten the
product life due to excessive wear, and may be dangerous causing damage
and/or personal injury.
AIR SUPPLY
Ensure wrench air valve (or trigger) is in the “off” position before connecting to the
air supply. You will require an air pressure of 90psi, and an air flow according to
specification. Drain the compressor air tank daily. Water in the air line will damage
the wrench. Clean compressor air inlet filter weekly. Recommended hook-up
procedure is shown in fig.1. Line pressure should be increased to compensate for
unusually long air hoses (over 8 meters). The minimum hose diameter should be
¼” I.D. and fittings must have the same inside dimensions. Keep hose away from
heat, oil and sharp edges. Check hose for wear, and make certain that all
connections are secure.
COUPLINGS
Vibration may cause failure if a quick change coupling is connected directly to the
wrench. To overcome this, connect a leader hose to the wrench. A quick change
coupling may then be used to connect the leader hose to the air line recoil hose.
See fig.1 & 2.
WARNING! Ensure you read, understand and
apply safety instructions before use.
Only use impact sockets which are specifically
designed for use with an impact wrench.
Connect the wrench to the air hose as in page 3.
Place the socket over the fastener nut and
depress the trigger to operate the wrench.
To change the direction, push the switch on near
the trigger to the desired direction. (fig.3)
The air flow may be regulated by adjusting the air
regulator dial on the bottom rear of the handle.
DO NOT use any additional force upon the
wrench in order to remove a nut.
DO NOT allow wrench to free run for an extended
period of time as this will reduce bearing life.
WARNING! Disconnect wrench from air supply before
changing accessories, servicing or performing
maintenance. Replace or repair damaged
parts. Use genuine parts only.
Unauthorized parts may be dangerous
and will invalidate the warranty. If the
air system does not have an oiler
lubricate the air wrench daily with a few
drops of air tool oil into the air inlet. Check
and top up the gearbox by removing grub
screw located under the impact head. Clean
the wrench after use.
DO NOT use worn, or damaged sockets.
Loss of power or erratic action maybe due to the
following:
a) Excessive drain on the air line. Moisture or
restriction in the air pipe. Incorrect size or
type of hose connectors. To remedy check the air
supply and follow instructions in chapter 3.
b) Grit or gum deposits in the wrench may also reduce
performance. If your model has an air strainer (located
in the area of the air inlet), remove the strainer and clean
it. Flush the wrench out with gum solvent oil or an equal mixture of SAE
No 10 oil and paraffin. Allow to dry before use.
For a full service, contact your local Sealey service agent.
When not in use, disconnect from air supply, clean wrench and store in a
safe, dry, childproof location.
OEM Limited One Year Warranty
For one (1) year from the date of purchase OEM tools will warranty this tool against
defects in materials and workmanship. Defective OEM brand hand tools purchased
from an authorized OEM distributor will be repaired or replaced when returned freight
prepaid to the OEM Warranty Dept., 3580 E. Raines Rd. #3, Memphis, TN
38118.Proof of purchase with date of purchase will be required with all returns.
OEM will not be responsible for any consequential or incidental damages arising
from the breach of this or any other warranty, whether expressed, implied or
statutory. Some states do not allow the exclusion or limitation of consequential or
incidental damages, so the above exclusion may not apply to you. This warranty
gives you specific legal rights, and you may also have other rights which vary from
state to state.
OEM® Company, Mineola, NY 11501
www.oem-tools.com
