Office Star Products A2MAD1730 User manual

© Ofce Star Products November 2022
STEP 4 MOUNT ADJUSTMENT
Adjust the monitor(s) height after installation.
If the Monitor Mount does not stop at desired height, use the
supplied Allen Wrench (G) to adjust screw(s) on Monitor Mount.
Turn the screw(s) clockwise to increase the tension, and
counter-clockwise to decrease the tension.
DESK
If the monitor(s) appear to droop/sag or turn too freely, use the supplied
Allen Wrench (G) to adjust the screw(s) at the pivot points. Turn the screw(s)
clockwise to increase the tension, and counter-clockwise to decrease the tension.
Cable
STEP 5 CABLE MANAGEMENT
A2MAD1730
DOUBLE MONITOR ARM WITH DUAL USB 3.0 PORTS
OPERATING INSTRUCTIONS
LIMITED WARRANTY
A2MAD1730 is warranted from the original purchase date to the original purchaser for normal commercial usage - dened as a standard forty-hour work week
according to the below-listed schedule and limitations.
• 3 year warranty
• Warranted against failure due to materials and workmanship
Warranty Exclusions
This warranty will not cover labor, freight, or damage from misuse, abuse, negligence, alteration, assembly, installation, attachments, accident, vandalism,
acts of nature or any other event beyond our control. The warranty does not cover cosmetic damage that may result from normal use. Liability for incidental or
consequential damage is excluded. The user assumes all risk of injury resulting from use of this product.
This warranty applies only to products purchased through authorized dealers and products sold within the United States of America and the Commonwealth of
Canada. This warranty does not apply to products used for rental purposes. This warranty gives you specic legal rights, and you may also have other rights which
vary from state to state.
WARNING
1. Do not use this product unless all bolts, screws and knobs
are securely tightened.
2. Check that all bolts, screws and knobs are tight every three
months or as needed.
3. Dispose of packing material properly. Do not use plastic
cover as head covering. It may cause suffocation.
4. Use this product for its intended purpose only.
5. Use mild detergent only for cleaning.
A2MAD1730
DOUBLE MONITOR ARM WITH DUAL USB 3.0 PORTS
OPERATING NSTRUCTIONS

PART QTY
1. Monitor Mount ......................1
2. Cable Cover ........................1
3. Anti-Slip Rubber 1 ...................1
4. Support Bracket .................... 1
5. Anti-Slip Rubber 2 ...................4
6. Threaded Clamp ....................1
7. Bottom Support .....................1
8. Threaded Stud ......................1
9. Anti-Slip Rubber 3 ...................1
10. Pressure Plate .....................1
11. Wing Nut .........................1
HARDWARE QTY
A. Phillips Bolt (M4 x 12) ................8
B. Phillips Bolt (M5 x 12) ................8
C. Allen Bolt (M6 x 12) ..................3
D. Allen Bolt (M6 x 14) ................. 2
E. Washer ..........................16
F. Allen Wrench (4 x 4) ..................1
G. Allen Wrench (5 x 5) .................1
Remove all the parts from carton, separate them into part numbers indicated on the list
and make sure part quantities are correct.
STEP 1 Ensure that there are VESA holes 100 x 100mm or 75 x 75mm in the
monitor(s) that is being mounted. If not, the monitor cannot be mounted. Carefully
remove the original xed base on the monitor(s).
STEP 2-A OPTION 1: CLAMP
STEP 2B OPTION 2: GROMMET
STEP 3 ATTACHING MONITOR TO PLATE
Phillips screwdriver also needed for assembly
(not provided)
TIGHTEN
DESK
Please select the appropriate
mounting holes according to
the desks thickness
NOTE
TIGHTEN
DESK
DESK
Keep the counterbore side down Size of hole: 8.5-70mm
For desk thickness: 25~100mm
Increase washer (E) count
if necessary
A2MAD1730
DOUBLE MONITOR ARM WITH DUAL USB 3.0 PORTS
ASSEMBLY INSTRUCTIONS
A2MAD1730
DOUBLE MONITOR ARM WITH DUAL USB 3.0 PORTS
ASSEMBLY INSTRUCTIONS