OIC Korea CMK-01 User manual
Installation and User’s Guide
http://www.oickorea.com
All contents of this document may change without prior notice, and actual product appearance may differ
from that depicted herein
Installation and User’s Guide
CM
K
-01
CEILING
MOUNT
FLAT LCD DISPLAY MOUNT MODEL
Installation and User’s Guide
htt
p
://www.oickorea.com
Warning Statements
The wall, floor or ceiling should be capable of supporting a weight of at least five (5)
times the monitor’s weight. If it cannot, the wall, floor or ceiling must be reinforced.
Proper installation procedure by qualified personnel as outlined in the installation
instructions must be adhered to Failure to do so could result in serious personal injury.
CAUTION! The entire installation instructions should be fully read and understood,
including all of the safety symbols and safety precautions before beginning installation.
The installation instructions should be read, understood and followed to prevent
personal injury or proper damage. Keep these installation instructions in an easily
accessible location for future reference.
CAUTION! The ceiling structure must be capable of supporting a maximum weight of
400 lbs. If not, the ceiling must be reinforced. Proper installation procedure by qualified
personnel as outlined in the installation instructions must be adhered to. Failure to do
so could result is serious personal injury.
CAUTION! Make sure to hold the plasma display, or projector, securely and remove it
from the mount to make the height adjustment prior to loosening the adjustment
screws. Do not remove the screws completely from the extension loosen all at once.
Loosen, remove, adjust then re-tighten the screws. Failure to do so could result in
injury and or damage to the plasma display or projector.
Indicates that the power plug is to be disconnected from the power outlet.
Safety precautions must be taken at all times.
Warning and caution in general
Installation and User’s Guide
htt
p
://www.oickorea.com
CM
K
-01
Installation
STEP1
Screw the CMK-01 coupling adapter to the adjustable suspension adapters or 1½" (NTP) Pipe.
Secure the coupling with the M6 security screw (supplied). Figure 1.
Cou
p
le
r
Cou
p
le
r
Swivel lock (Located
inside Cou
p
ler
)
Keyhole mounting
opening
VESA 75 / 100
Mounting points
Adjustable Ceiling Adapter
Single Stud Installation
STEP2
Secure the ceiling plate to the ceiling structure (see WARNING).
STEP3
Use suitable hardware (commercially available) depending on your installation environment to
secure the two (2) mounting points found on the ceiling plate to the ceiling structure (Figure 2).
STEP4
Refer to ceilin
g
ada
p
ter installation instructions.
Fi
g
ure 2
This hardware is commercially
available and is not included
in the hardware pack.
Relocate ad
j
ustment screw
Cable access o
p
enin
g
(Commercially
Available) Suitable
Hardware minimum
of 1/4” x 2” Lag bolt
required
Lower tube
U
pp
er tube
Ad
j
ustment screw
Use the two (2) slots on the ceiling
Plate for single stud mounting
Ceiling structure
(See warning)
Minimum of 2” x 4”
W
ood stud
Installation and User’s Guide
htt
p
://www.oickorea.com
Solid Structure Installation
1. Secure the ceiling plate to the ceiling structure (see WARNING).
2. Use suitable hardware (commercially available) depending on your
installation environment to secure the four (4) mounting points found on the
ceiling plate to the ceiling structure (Figure 3).
3. Refer to ceiling adapter installation instructions
Fi
g
ure 3
This hardware is commercially
available and is not included
in the hardware
p
ack.
R
e
l
ocate
adjust
m
e
n
t
sc
r
e
w
L
o
w
e
r
tube
Uppe
r
tube
A
djust
m
e
n
t
sc
r
e
w
(CommerciallyAvailable)
Suitable Hardware
CEILING
STRUCTURE
(SEE WARNING)
Installation and User’s Guide
htt
p
://www.oickorea.com
TENSION
ADJUSTMENTS
VESA 100: Secure the VESA 75/100 mounting bracket to the VESA 75 Using the four M4 x 10
Phillip screws. Raise and secure your monitor to the plate that has the VESA 100 now on you CMK-
01 adapter and use the four (4) M4 x 10 (mm) Phillips screws (supplied) and a Phillips screwdriver.
(Do not use other tools other than a Phillips screwdriver to prevent damage to the monitor or
mounting points).
CAUTION: Do not over tighten the screws to the monitor failure to do so could result on
damaging the monitor or the mounting points. See figure 4.
Fi
g
ure 4
(4) M4 x 10mm
Phillips Flat Head screws
Adapter Plate
75 MM /
100 MM VESA
plate
(4) M4 x 10
Philli
p
s
M6 X 8mm Set
Screw
Swivel tension
Tilt tension
Installation and User’s Guide
htt
p
://www.oickorea.com
Technical Specifications
Features: Tilt mount allows of adjustments up and down of ±90° from center and
360° swivel and cable access. Comes with a combination plate of VESA 75 and VESA 100 for
optional mounting depending on monitor.
M6 x 8mm set
screw
Coupler
Swivel lock
(Located inside
Coupler)
Keyhole
mounting
opening
VESA 75/100
mounting points
VESA 75 to VESA 100 front plate
NOTE: Only used for monitors
that are VESA 100
Installation and User’s Guide
htt
p
://www.oickorea.com
2Year Limited Warranty
Contact OIC Korea
All OIC Korea products carry a limited warranty from ship date against defects in materials and
workmanship. OIC Korea is not liable for improper installation that results in damage to mounts,
adapters, display equipment or personal injury.
In the event of missing and/or damage equipment, or technical questions, the
following information can help in the completion of the installation.
Address: 403-403, Bucheon Technopark 4 Danji Apt., 193, Yakdae-dong,
Wonmi-gu, Bucheon-si, Gyeonggi-do 420-734, Korea
Tel: 82-70-7510-2809 / Fax: 82-70-8240-4403\
Email: [email protected]
Website: http://www.oickorea.com
Table of contents
