Okina HI11-TKHBL User manual

HI7-TKHBL_HI11-TKHBL_rev0427091
Operational Manual
Super Power IR LED Illuminator & Professional Camera Housing
HI7-TKHBL
HI11-TKHBL
* UL certification only refers to the power converter and the power module
FEATURES
Please read the Operational Manual
before attemptin
g
to use this product.
11 Super Power IR LED, 6pc x 25o
/
5pc x 45o
IR Distance up to 395ft / 120m 
IP66 Rating
User Adjustable IR LED Intensity (VR), Factory Default 80% 
Fully-Cable Managed Bracket
Uses professional rust-proof stainless steel screws
Heater & Blower
24V AC, 60VA, Power Ready Plug for 12V DC Camera
7 IR LED
11 IR LED
Please see page 6
FEATURES
7 Super Power IR LED, 4pc x 25o
/
3pc x 45o
IR Distance up to 250ft / 80m 
IP66 Rating
User Adjustable IR LED Intensity (VR), Factory Default 80% 
Fully-Cable Managed Mounting Bracket
Uses professional rust-proof stainless steel screws
Heater & Blower
24V AC, 60VA, Power Ready Plug for 12V DC Camera

HI7-TKHBL_HI11-TKHBL_rev0427092
PART DESCRIPTION

HI7-TKHBL_HI11-TKHBL_rev0427093
1. Lens Cap with Heater
2. Temper Glass
3. IR LED: 7pcs or 11pcs Super Power IR LED with Refractor
4. IR Board and IR Board Bracket
5. Universal IR Control Circuit Board: When the IR light turns on, it automatically adjusts the color to monochromatic
through the universal IR control circuit.
6. Camera Bracket
7. Power Supply Unit: 24V AC input, 60VA
8. Blower and Blower Bracket
9. Thermostat Switch
10. Video Input BNC Male Connector: Connect to camera
11. Video Out BNC Female Connector: Connect to monitor
12. Terminal Board
13. Fuse Holder: With 250V / 3.15A fuse
14. AC IN Terminal block: 24V AC external power input
15. OUTPUT_1 Terminal block: Plug and fix the power cable of camera
16. OUTPUT_2 Terminal block: To power supply unit
17. VR: Adjust VR to set Infrared LED activation level
Factory default 80% -- If there is not enough IR light, adjust the level to maximum 100% 
18. Thermostat Switch: Turns on at 35C / 95F and turns off at 25C / 77F for Blower
19. Ground wire: To top cover
20. 12V DC Power-in jack: To camera / center+, outer-
When using a camera which requires a 24V AC power input, please run a separate power line to the camera
21. Flying Bare Lead Wire: When the wire is not in use, cover it with the screw-on connector or tape the tip with tape to
prevent damages caused by the bare lead wire.

HI7-TKHBL_HI11-TKHBL_rev0427094
1. Loosen two screws on both sides of the camera bracket first.
2. Use the provided screw to fix the camera (not included) on the camera bracket.
3. Adjust zoom, focus and iris of the lens on the camera.
4. Adjust the direction of the camera for proper position, after finished tighten all screws.
How to install cables through the mounting bracket:
INSTALLATION

HI7-TKHBL_HI11-TKHBL_rev0427095
NOTE: When using two-cord power cable, please connect them to “Live” and “Neutral.”
HI7-TKHBL / HI11-TKHBL:
Fully-Cable Managed Bracket:
Max Load: 3500g
Material: Die-cast aluminum alloy with light ivory powder coated and stove
finish
Scan Angle: 180°
Tilt Angle: 90°
Net Weight: 900g
Fixing: 3 Screws with bushings
EXTERNAL POWER INPUT CONNECTION
DIMENSIONS
(
mm
)

HI7-TKHBL_HI11-TKHBL_rev0427096
Model HI7-TKHBL HI11-TKHBL
LED Quantity 7 Super Power IR LEDs 11 Super Power IR LEDs
IR LED Beam Angle 4pc x 25o/ 3pc x 45o6pc x 25o/ 5pc x 45o
IR Wave Length 850nm
IR Distance 250ft / 80m 395ft / 120m 
IR Light On/Off Auto Light Sensor Control
Heater Control 18C / 64F (on); 28C / 82F (off)
Blower Control 35C / 95F (on); 25C / 77F (off)
IP Rating IP66
Temper Glass
Thickness 4mm
Mounting Bracket Full-Cable Management
Construction Die-Cast Aluminum Alloy
Coating Ivory Powder Stove
Required Power
Supply /
Transformer * 24V AC (+/-10%), 60VA
Power Consumption 9 Watts 16 Watts
Dimension 16.73”(L) x 6.30”(W) x 6.50”(H) / 425mm(L) x 160mm(W) x 165mm(H)
Camera Space 7.87”(L) x 4.33”(W) x 4.53”(H) / 200mm(L) x 110mm(W) x 115mm(H)
Weight 7.72 lbs / 3500g (w/out bracket)
11.55 lbs / 5240g (with bracket) 7.72 lbs / 3500g (w/out bracket) 11.75 lbs / 5330g (with bracket)
* Power supply / transformer not included
NOTE 1: IR light distances are entirely dependant upon environmental site conditions and the location at which the unit is situated. The type
of camera being used is also very important.
NOTE 2: Factory default for the IR LED activation level is 80%. If there is not enough IR light, adjust the VR level to maximum 100%. Please
see #17 in the Part Description section on page 1.
One (1) HI7-TKHBL or HI11-TKHBL IR Illuminator & Professional Camera Housing
One (1) Fully-Cable Managed Bracket
One (1) Operational Manual
One (1) Main Accessories Pack
Three (3) Rust-proof Stainless Steel Wall Screws
Three (3) Rust-proof Stainless Steel Mounting Screws
Three (3) Stainless Steel Washers
Three (3) Plastic Washers
One (1) Allen Wrench
One (1) Secondary Accessories Pack
Three (3) Screw-on Connectors
One (1) Rubber Pad
One (1) Rust-proof Stainless Steel Camera Screw
One (1) Plastic Washer
* For any returns, please include all components listed above with original packaging in Resalable Condition. Absolutely No
Returns will be accepted if any component is missing/damaged or if any cable is cut or tampered with.
GENERAL SPECIFICATIONS
PACKAGE CONTENTS

HI7-TKHBL_HI11-TKHBL_rev0427097
OKINA USA Products are covered under warranty for one year from the date of purchase. The warranty will
automatically be voided if any of the following occurs:
1. Product sticker is removed
If the product sticker is removed, we will not be able to confirm any information regarding when and where the
product was purchased. We have no other way to verify the purchase record without the serial number on the
product sticker; therefore, it should not be removed.
2.
Product is modified in any way
If the product is scratched, damaged, or modified in a manner not described in this manual, the warranty will be
voided immediately. It is the customer’s responsibility to keep the product in good condition.
3. Power cable is cut
The power cable and any other cable should not be tampered with. Cutting or modifying of the cables will result in
termination of the warranty.
1. Read and follow instructions
All operating and user instructions should be read and followed before the unit is to be operated.
2. Secure all screws
Please make sure all rust-proof stainless steel screws are installed securely to ensure a waterproof seal.
3. Electrical connections
Only a qualified electrician should be allowed to make electrical connections.
4. Do not disassemble the product
Do not disassemble the product as it is dangerous and may cause damage to the product. Refer all servicing to
qualified service personnel.
5. Handle the product with care
Be careful when handling the product. Do not drop it or subject it to strong shock or vibrations in order to prevent
any damage to the product. Do not handle the product in a wet environment or when your hands are wet.
6. Reducing risk
To reduce risk of fire or electric shock, do not remove cover. Do not open product in wet weather. No user serviceable
parts inside. Refer servicing to qualified service personnel.
7. Unpacking
Unpack carefully. Electronic components can be damaged if improperly handled or dropped. If an item appears to
have been damaged during shipment, please place it properly in its carton and notify the shipper.
8. Installation notice
Tropical, coastal salt water environment:
If you plan to install this product into a tropical, sea, coastal salt water or corrosive industrial water/mist
environment, please seal each stainless screw and fitting with a silicon grease compound. This will help prevent
electrolysis corrosion occurring and extend the lifespan of the product and housing and prevent premature
deterioration.
9. Voltage
If you are using a camera which requires a 24V AC power input, please run a separate power line to the camera.
WARRANTY
IMPORTANT NOTE

HI7-TKHBL_HI11-TKHBL_rev0427098