Okina OK-PTZ-KB250X User manual

Operation
LCD
Display
Digit Keys
3 Axis Joystick
Camera
Function keys
Function Keys
Cam ID:001 Mon ID:001
Protocol:
Baudrate: 9600bps
B01
Initial Screen
PT Operation with Joystick
Zoom operation
Cam ID: Current camera ID
Mon ID :
Protocol:
Baudrate:
Current monitor ID, indicates the ouput setting on matrix.
Telemetric protocol setting.
Baud-Rate setting
The LCD back-light will be turned off automatically after 15 seconds of
idle time.
Move the joystick up, down, left and right to perform pan or tilt
operation. Depends on the angle of stick, the keyboard changes the
speed of PT movement. On performing the PT action, the LCD will
show the current movement with arrow signs
The keyboard provides camera function keys with following function:
Wide / Tele: Zoom-out and zoom-in
Far / Near: Manual focus control
Open / Close: Manual Iris control
RS-485 (A+/ B-)
For connection to PTZ, Speed-Domes or other device which support
telemetric controling with RS-485 interface. The max. Distance can be up to
1000 meter ( depends on cable and environmental condition).
RS-422 (T+/T-/R+/R-)
RJ-45
DC Power Input
Rs422 Inteface for telemetric control, up to 1200 meters.
Control interface forr matrix device(e.g. Pelco Cm6700,CM6800).
Power supply for the keyboard, Voltage range is 9V to 12V in DC or AC
without polarity( auto-sensing). When connecedt to the Matrix, the keyboard
can be powered thourgh the RJ-45 Interface.
Please make sure that the following chapters are set correctly:
Cable Connection: Make sure that the RS485/422 cable are connected
correctly to the camera devices.
Baud-Rate:
Protocol:
Camera ID
The keyboard and the camera devices must have the same
baud-rate setting, in order to establish the data exchange. Available settings
are 2400, 4800 and 9600 Bps. For settings on the camera device, please
refer to camera’s manual for further details.
Make sure that the keyboard and camera devices are set with the
same protocol. Currently Pelco and B01/B02 are supported by the
keyboard.please refer to camera’s manual for details.
: Make sure that every connected PTZ device is assigned with
an unique ID.
For settings of your keyboard. Please refer to later chapters for details
B(+)
TX(+)
RX(-)
TX(-)
RX(+)
TX(+)
RX(-)
TX(-)
RX(+)
B(+)
A(+) A(+)
2
24-
SR
5
8
4
-SR
Check list
Matrix related functions
Switching the input channel.
Auto switching sequence
Open matrix conguration menu
Conrm changes
Change target monitor
Press [PREV] : switch to previous channel
Press [NEXT] : switch to next channel
Press [PREV] for 2 sec.: Sequence in rev. order
Press [NEXT] for 2 sec.: Sequence to next channel.
Press [STOP] to stop the sequencel.
Press [SHIFT] + [SET] to enter the menu and show on main
monitor. For the menu details, please refer to the users manual of
the matrix.
Press [ENTER] after every changes in the menu.
Press [n] + [MON] to change the selected device in the matrix.
PTZ related functions
With the keyboard, you can activate or setup the integrated function of
connected camera device. For the supported functions, please refer to
camera’s manual for further details.
Press [n] + [CAM] : n.. ID of the camera
Move the PTZ to the desired position and press
[SET]+ [n] + [PRESET]
To store the current position as a preset n
To recall the memorized preset position, press
[n] + [PRESET]
N.... The number of preset to be recalled.
You need to enter the keyboard’s menu to setup the tour. Pleare
refer to the later chapter for setup.
To start the tour, press
[n] + [TOUR]
N.. Number of the stored tour
Scan between 2 pre-defined points. To define the points, move to
the left end and press [SET]+[1] + [SCAN], and move to the right
end and press [SET] +[2]+ [SCAN] to store the position.
For changing the scan speed, you need to enter the PTZ’s OSD
menu. Please refer to the users manual for details.
Press [1]+[SCAN] to start the scan procedure.
The pattern function records user’s PTZ movement, and can be
recalled when need. Depends on the camera device, the
recording time and supported number of pattern tracks might
differ. To start the recording procedure, press
[SET] + [n] + [PATTERN]. n....the number of pattern track.
To stop the pattern recording, press
[SET] + [0] + [PATTERN]
To activate the recorded pattern, press
[N] + [PATTERN]
Change currently selected camera
Set / dene a Preset position
Recall / activate Preset position
Set Tour function (B01)
Recall / activate Tour
Setup 2-Points scan
Start 2-Points Scan
Start / Stop Pattern recording
Activate recorded Pattern
- Refer all work related to the installaion of this product to qualied
service personnel or system installers.
- Do not attemp to disassemble the keyboard
- Handle the keyboard with care.
- Do not operate the apliance beyond its specied temperature,
humidity or power source ratings.
- Read this user's manual carefully before operation.
To prevent electric shock,
do not remove screws or cover. There are no user-serviceable parts
inside. Contact qualified service personnel for maintenance
Do not str ik e or shake, as this may
damage the keyboard. It should be protected against extreme pressure,
vibration and humidity during transportation, storage and operation.
Damages caused by improper transportation avoid the warranty.
Do not u se t he keyboard in a n
extreme environment where high temperature or high humidity exists.
Use it within -5°C to +40°C(23°F to 140°F) and a humidity below 90%.
The input power source is 12V DC, and requires at least 500mA.
Make sur e th at
local electric safty standards are followed when using or installing the
keyboard.
- Do not install this Product in a ammable and explosive
environment.
Before installation and mentainence, make sure that the keyboard is
disconnected from the power source.
Do not install or operate the keyboard near any high-voltage devices
or high-voltage cable.
This product should be operated indoor only.
-
-
The safety distance should remain at least 50 m.
-
Before Starting
Technical specications are subjects to change without prior notice. This
Manual may contain printing or clerical errors. All trademarks mentioned
belong to their respective owners.
1 X Controller 1x User Manual
AC-DC Power
Supply (optional)
Connection
USER'SMANUAL
Programm able
Keyboard C ontro ller
Matrix
Power
Input
Matrix
Interface
RS-485
up to 32 Devices
RS-422
Interface
DO NOT CONNECT THE RJ-45 PORT
TO ANY COMPUTER NETWORK
INTERFACE, as this may cause serious
damage to the keyboard.
Unpacking
3-Axis Compact
Keyboard Controller
User's Manual
Warning
TO REDU CE T HE R ISK OF F IRE OR E LECTR IC S HOCK, DO NOT EX PO SE THIS
PRODUCT TO RAIN OR MOISTURE. DO NOT INSERT ANY METALLIC OBJECTS
THROUGH THE VENTILATION GRILLS OR OTHER OPENINGS ONTHE EQUIPMENT.
FCC COMPLIANCE STATEMENT
CE COMPLIANCE STATEMENT
CAUTION: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY
RESPONSIBLE FOR COMPLIANCE COULD VOID THE USERS‘S AUTHORITY TO OPERATE THE
EQUIPMENT.
FCC INFORMATION: THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE
LIM IT S FO R A CLA SS A DI GITA L DEV IC E, P URS UAN T TO PA RT 15 OF T HE FC C R ULE S. T HES E
LIMITS ARE DESIGHEND TO PROVIDE REASONABLE PROTECTION AGAINST HAMRFUL
INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT. THIS
EQUIPMENT GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY ENGERGY AND IF NOT
INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE HARMFUL
INTERFERENCE TO RADIO COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN A
RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE IN WHICH CASE THE USER
WILL BE REQUIRED TO CORRECTTHE INTERFERENCE AT HIS OWN EXPENSE.
WARNING: THIS IS A CLASS A PRODUCT. IN A DOMESTIC ENVIRONMENT THIS PRODUCT MAY
CAUSE RADIO INTERFERENCE IN WHICH CASE THE USER MAY BE REQUIREDTO TAKE ADEQUATE
MEASURES.
CAUTION: TO REDUCE THE
RISK OF ELECTRIC SHOCK,
DO N OT RE MOV E COVE R (
OR BA CK). NO U SE R
SER VIC EAB LE PARTS
INSIDE. REFER SERVICING
TO QUALIFIED SERVICE
PERSONNEL
This symbol indicates that
dangerous voltage constituting a
risk of electric shock is present
within this unit.
This symbol indicates that there
are important operating and
maintenance instructions in the
literature accompanying this unit.
This Symbol indicates that this product should not be treated as household
waste. When discarding this product, it must be sent to appropriate facilities for
recycling or recovery. By separating this product from other household waste,
you are helping to reduce the volume of waste incinerators and the natural
resource will be conserved.
OKINA
OKINA
OK-PTZ-KB250X

Keyboard Menu
1 Keyboard setup
2 Dome s etup
3 Protocol select
4 Exit m enu
、
、
、
、
About keyboard
Version:1.00
KB ID :0 08
Protocol:Factory
Baudrate:2400
1 Jo y is fr ee th en
Press ENTER
、
Joy_calibrate
Keyboard setup
1 Set KB Parameter
2 About keyboard
、
、
1 Se t KB ID :
2 Set baudrate
3 Joy_calibrate
、
、
、
Set KB Parameter
Inp ut K B ID:
Set KB ID
1 24 00 bp s
2 48 00 bp s
3 96 00 bp s
4 19 200 b ps
、
、
、
、
Set baudrate
1 Se t dom e pre set
2 Se t dom e sca n
3 Set dome pattern
4 Se t dom e tou r
、
、
、
、
Dome setup Set dome preset
1 Save preset
2 Show preset
3 Clear preset
、
、
、
Preset num:
Pre ss p rev t o bac k
1 Tour n um:
2 Insert preset
3 Ru n tou r
、
、
、
1 Se t lef t lim it
2 Se t rig ht li mit
3 Ru n sca n
、
、
、
Set dom e scan
Press enter sure
Pre ss p rev t o bac k
Press enter sure
Pre ss p rev t o bac k
Set lef t limit Set right limit
Pre ss 1 t o sta rt
Pre ss p rev t o bac k
Pre ss 0 t o sto p
Run pattern
Set pattern
Success!
1 Pattern num:
2 Set pattern
3 Run pattern
、
、
、
Set dome pattern
Set dom e tour
1 Preset num:
2 Speed:
3 Dwell:
、
、
、
Run tou r
Success!
1 Matrix
2 Dom e
、
、
Protocol select
Success!
Run sca n
Success!
Pelco matrix
1 Pelco matrix、
Matrix
Success!
Dome
1 Factory
2 Pelco-P
3 Pelco-D
4 B02
、
、
、
、
Exit menu
CamID:001 MonID:001
Protocol:Pelco-P
Baudrate:9600
Insert preset
1 Keyboard setup
2 Dome setup
3 Protocol select
4 Exit menu
.
.
.
.
1. Set KB ID
2. Set baudrate
3. Joy_calibrate
Enter the keyboard menu
To enter the keyboard’s setup menu, keep the [SET]-Key pressed for 2
seconds, To navigate through the menu items, use the joystick with “up”
and “down” to move between the items. Use “right” to enter the item or
confirm changes. Use “left” to leave the item or discard changes”
In main menu, you can select the
items by pressing the digit key, or use
joystick to navigate through the items.
For returning to upper menu level,
press [PREV] key. Use the [ENTER]
Main Menu
Keyboard Setup > Set KB Parameter
key to confirm the changes. The display will show “SUCCESS” when
changes are accepted.
Setup keyboards ID, Baud-rate and
calibrates the joystick.
Joystick up/down to select item
[ENTER] to enter the sub-menu
[PREV] return to upper level.
1. Set KB Parameter
2. About keyboard
Keyboard Setup
Initial setup for the keyboard, such as
keyboard ID, and baud-rate. Press
digit key to enter.
Input KB ID:
(1 - 64)
Keyboard Setup > Set KB Parameter> Set KB ID
Use the digit keys to enter the ID, and
press [ENTER] to confirm. LCD will
show “SUCCESS” when accepted, or
“ERROR” if the ID input exceeds the
range.
Joystick is free
then
press Enter
Keyboard Setup > Set KB Parameter> Joy_calibrate
Release the joystick, and press [ENTER]
to confirm the calibrate of zero-point .
Press [PREV] to return to upper level.
Version: 1.00
KB ID: 001
Protocol: B01
Baudrate: 9600 bps
Keyboard Setup > About keyboard
Information about current keyboard
setting. Press[PREV] to return.
2400 bps
4800 bps
9600 bps
19200 bps
Keyboard Setup > Set KB Parameter> set baudrate
Available baud rate. Move joystick “up’ or
“down” to select the setting and press
[ENTER] to confirm.
Press [PREV] to return to upper level.
1. Set dome preset
2. Set dome scan
3. Set dome pattern
4. Set dome tour
Dome setup
Configure and setup the PTZ related
functions, such as preset, pattern... Etc.
Preset num:
Press PREV to back
Dome setup > Set dome preset> Save, show or clear preset
Enter the preset number with the digit key,
For saving preset, move the joystick and
press [ENTER]. To show or clear the
preset, enter the preset number and press
[ENTER], or press [PREV] to exit.
1. Save preset
2. Show preset
3. Clear preset
Dome setup > Set dome preset
Save, recall and clear the preset points.
Press 1 to start
Press 0 to stop
Press PREV to back
Dome setup >Set dome pattern > Set pattern
Press 1 to start the pattern recording. The
dome will now memorize your PTZ
operation. When finished, press 0 to stop
the recording. Press [PREV] to exit the
menu
1. Set left limit
2. Set right limit
3. Run Scan
Dome setup > set dome scan
Setup the 2-Points scan, select 1. And 2.
To define the left and right limit. Select
option nr. 3. To run the scan
Press ENTER sure
Press PREV to back
Dome setup >set dome scan> set left, right limit
Move the Joystick to the desired position
and press [ENTER] for confirmation.
1. Pattern num:_
2. Set pattern
3. Run pattern
Dome setup >Set dome pattern
1: Press the digit and [ENTER] to select
the pattern number.
2: Sub-menu for pattern setup.
3: start the selected pattern
1. Preset num:_
2. Speed:
3. Dwell:
Dome setup >Set dome tour> Insert preset
1. Preset num:_ select the defined preset
position ( 1 - 80)
2. Speed: PTZ moving speed to this
preset, 1 - 8 ( fastest)
3. Dwell: Stop time on this preset. Max. 60
seconds.
1. Tour num:_
2. Insert preset
3. Run tour
Dome setup >Set dome tour
1: Press the digit and [ENTER] to select
the tour number.
2: Add defined preset position to the tour
3: start the selected tour
Use the digit keys to change the value on every option, and press [ENTER]
to complete the insert action. The LCD will show “SUCCESS” to confirm the
preset, and returns to upper menu level.
1. Pelco Matrix
Protocol select >Matix
Currently only pelco protocol is supported
in the matrix mode. Press [ENTER] to exit.
1. Matrix
2. Dome
Protocol select
1. Matrix: Matrix Mode
2. Dome: Setup Dome Protocol
1. Factory protocol
2. Pelco-P protocol
3. Pelco-D protocol
4. B02
Protocol > Dome
DO NOT CONNECT THE RJ-45 PORT
TO ANY COMPUTER NETWORK
INTERFACE, as this may cause serious
damage to the keyboard.
Quick Reference
[N] + [CAM] Select the connected
device
[TELE] Zoom-In
[WIDE] Zoom-Out
[FAR] Manual focus far
[NEAR] Manual focus near
[CLOSE] Manual iris close
[OPEN] Manual iris open
[SET]+[N]+[PRESET] Store current PTZ
position as preset
[N]+[PRESET] Recall stored preset
position
[SET]+[1]+[SCAN] Define current position
as the left limit for scan
[SET]+[2]+[SCAN] define current position
as the right limit for
scan
[1]+[SCAN] Start the scan
[SET]+[N]+[PATTERN] Start pattern recording
[SET]+[0]+[PATTERN] Stop the pattern
recording and store.
[N]+[PATTERN] Start recorded pattern
[N]+[TOUR] Start the defined tour.
Connection sample
Star-Connection with
RS-Distributor
RS 48 5+
RS 48 5-
Termination
On
Termination
On
Termination
Off
Termination
Off
Keyboard
Termination on RS-485 chain
Dom e 2Dome 4
Dom e 3
Keyboard
Dom e 6Dome 8 Dom e 7
Dom e 5
Keyboard
Keyboard
Keyboard
Dom e 1
Multiple device connection
Max. 32 devices
(Keyboard and camera)
can be connected to a
RS-485 chain. E.g with 1
keyboard, you can max.
Connect 31 Speed
Domes.
For a multiple connection, you can
attach max. 4 keyboards to the
network. Make sure that every
keyboard has an unique ID.
RS-485
Distributor
Termination
Activated
on every dome