minikon CND1 User manual

4231=EN
VERSION 1119
CND1 - Quick start guide
EN

==
Pro-Line 28/50/70 CND1 - Control box installation EN
2x 4249
2x 8080
4x 8230
4x 8085
2x 8280
8085 82304249 8080 8280 CND14x 4x2x 2x 2x 1x
1Position of spiral cable bracket

Pro-Line 28/50/70 CND1 - Connection of door control boxes EN
1 2
3 4
5 6
4x 9382
PH1

DW: Module 12 + 13
Duo Opto: Module 20 + 21
D
C C
A
B
D
D
C C
D
B
B
D
D
D
A
D
B
D
C
D
B
D
C
A
B
D
Connections
A = Spiral cable
B = Connecting cable
C = OPTO / OSE1 / OSE2
D = SCD L/R / PD Switch
Opto: Module 10 + 11
7Connect cables to circuit boards in door control boxes
8
EN

Pro-Line 28/50/70 CND1 - Basic installation 1/2
NOTE! Do not plug in CEE plug yet!
✓
2x
4x
1 2
3
EN
PH2

1
ON WE
32 4
X7
S4
X16
X2
X13
X3.8
X3.7
X20
X20
X3.7
X3.8
X13 X2
X16
S4
X7
X20
X3.7
X3.8
X13
X2
X16
S4
X7
Pro-Line 28/50/70 CND1 - Basic installation 2/2
NOTE! Do not plug in CEE plug yet!
X20
X3.7
X3.8
X13 X2
X16
S4
X7
X20
X3.7
X3.8
X13
X2
X16
S4
X7
4
5
X3.7
DW
X3.8 X20
X13 X16 X2
Opto / Light curtain SCD / Passdoor
Shaft drive encoder Shaft drive ground wire Shaft drive feed
EN
3,5
OR!
Programming mode
Spiral cable
Shaft drive cable

Pro-Line 28/50/70 CND1 - Basic programming 1/2
NOTE! Plug in the CEE plug to program the control box.
*NOTE: If the door does not move upwards
but downwards when the UP button is
pressed, the phases in the CEE plug must
be reversed. Use a slotted screwdriver to
do so. Then repeat steps 2 through 5.
Keep
pressed
Release
button
Display
Until
Display:
=
Display:
=
Display:
Move switch 1 to ON
Door open
2 3
5
1
4*
1
ON WE
32 4
2x
3x
1x
4 sec.
ON WE
1 32 4
Determine open door position
EN
6,5
=
Activate programming mode
✓

✓
Pro-Line 28/50/70 CND1 - Basic programming 2/2 EN
Keep
pressed
Release
button
Until
Display:
=
Display:
=
Display:
6 7
9
8
12
2x
1x
4 sec.
Determine closed door position
Door closed
Door closed
Exit programming mode
Check the operation of the door
Move Switch 1 to OFF
10
1
ON WE
32 4
ON WE
1 32 4
Door open
11
1x
1x

X7
S4
X16
X2
X13
X3.8
X3.7
X20
Pro-Line 28/50/70 CND1 - Installing remote control
NOTE! Only plug in the CEE plug and peripheral
equipment after connecting all of the plug-in plugs in the
way described below.
NOTE! Insert the
plug-in circuit board rmly
to ensure a good contact.
X20
X3.7
X3.8
X13 X2
X16
S4
X7
1 2 X7
EN
Option remote control

Pro-Line 28/50/70 CND1 - Programming the remote control
Pro-Line 28/50/70 CND1 - Disconnecting the remote control
A sound will be made as long as the
button on the plug-in circuit board is
pressed. At the same time, press the
button on the remote control!
Test the operation of the remote
control. Repeat the connection
procedure if it does not work.
A sound will be made as long as the
button on the plug-in circuit board is
pressed. At the same time, press the
button on the remote control!
Test the operation of the remote
control. Repeat the disconnection
procedure if it does not work.
1
1
1 sec.
1 sec.
Keep
pressed
Keep
pressed
+
+
2-Channel
Remote
control
Remote
control
4-Channel
EN
Option remote control
NOTE! Plug in the CEE plug to be able to connect
to the remote control.
✓