OleumTech Wio RM1K User manual
4. Installaon Best Pracces
Quick Start Guide
Modular Wireless I/O System - RM1K
1. Before You Begin
2. Required Items
-
3. System Setup Instrucons
SMA
NEMA-Type
Enclosure
WARNING!
9-30 Vdc
NPN
NPN
5. Hardware & Wiring Diagrams
6. I/O Chain Diagram
When Enabled:
When Disabled:
FailSafe State:
DIGITAL
P1
P2
P3
A
B
C
1 2
1 2
2/4 COM1/3INPUT
OUTPUT 2/4 COM1/3
DO
1
DO
2
DO
3
DO
4
Enable / Disable
FailSafe State
OFF
ON
Default
DIP SWITCHES
ANALOG 4-20 mA
P1
P2
P3
A
DIP SWITCH
VS+ SIG
ON
SENSOR
N/C
+
_
+13.5 V
DIP SWITCH
OFF
N/C
SENSOR
+
_
EXT.
POWER
+
_
AI2 AI1
OFF
ON
Default
SIG COMVS+
-N/C
+
EXT.
POWER
+
_
ANALOG 0-10 V
P1
P2
P3
A
AI DEVICE
COM
COM
AI
AO N/C
SENSOR
COM
COM
V+
+13.5 V SIG
SIG
All inputs and outputs
TYPE POWER CONSUMPTION
Quick Start Guide
Modular Wireless I/O System - RM1K
7. Power Consumpon
RADIO
9-30 V COMCOM
to switch between modes
P2
P1
P2
P3
A
B
C
10 11 12
+5 V DO
DI
10K
30 V MAX
OPTIONAL COM
4 5 6
+5 V DO
DI
10K
30 V MAX
OPTIONAL COM
10 12
DI
COMCOM
8
COM
VS+ SIG COM
1
1
4
Sta�on A Sta�on B
NPN NPN
+-
9-30 V
NPN
+-
9-30 V
Dry Contact
NPN NPN
NPN
Quick Start Guide
Modular Wireless I/O System - RM1K
10. 4-20 mA External Power Loop8. Isolaon vs Non-Isolaon 9. 4-20 mA Internal Power Loop
- +
Sensor
DIP Switch
Must be O
V
+ -
Power
to AI+ / SIG
+ -
Sensor
+13.5 V
DIP Switch
Must be On
to AI+ / SIG
13. Digital Level Input - Acve High11. Dry Contact Input 12. Digital Level Input - Acve Low
+-
9-30 V
Open/O = 2.4 to 30 V (Vih = 2.4 V)
Closed/On = 0 to 1.0 V (Vil = 1.1 V)
LEDs turn on when 0 to 1 V is detected
LEDs turn o when 2.4 to 30 V is detected
DO COM
Signal Controller
COIL
VOUT COM
PLC Voltage Output
Relay
+
-
9-30 V
+-
9-30 V
If the Digital Input requires higher
than 4.7 V, use an external pull-up
resistor (10 K, up to 30 V max)
Open/O > 4.7 V
Closed/On = 0 V
DI COM
Digital Level Input
NPN
+-
9-30 V
Open-drain with +5 V internal pull-up
Vout max = 4.7 V
Open/O = 4.7 V
Closed/On = 0 V
DI COM
Digital Level Input
Internal pull-up
NPN
NPN
NPN
15. Digital Level Output - Acve Low 16. Digital Level Output - Acve Low
10 K
External pull-up
+
+
-
-
9-30 V
COIL
VIN COM
PLC Voltage Input
Relay
10 K
Pull-Down Resistor
(Optional)
Quick Start Guide
Modular Wireless I/O System - RM1K
17. Digital Level Output - Acve High
4-20 mA
Analog
Input
V-
SIG-
SIG+
V+
+-
Ext Power
18. 4-20 mA Output
14. NPN Output
Open-drain (NPN) Outputs
Inductive Load (Sink Current):
1 Amp/30 Vdc
Relay
+
-
+-
9-30 V
Other OleumTech I/O System manuals
Popular I/O System manuals by other brands
WAGO
WAGO WAGO-I/O-SYSTEM 750 Series manual
CREVIS
CREVIS GT-2 Series user manual
ICP DAS USA
ICP DAS USA M-7011 quick start guide
Unitronics
Unitronics UID-W1616R user guide
M-system
M-system R7F4HEIP-DAC16B instruction manual
National Instruments
National Instruments Low-Cost Multifunction I/O Board for ISA... user manual
