Ollee MINI Series User manual

User Guide for Ollee Mini PC MAPMG
1
Ollee Ultra Mini PC, a Mini PC with 32GB eMMC and Windows® 10 Pro –
MAPMG
Ollee Ultra Mini PC, a Mini PC with 120GB SSD and Windows® 10 Pro –
MAPMG1
User Guide
Before You Begin
CAUTIONS
The procedures in this guide assume familiarity with the general terminology associated with personal
computers and with the safety practices and regulatory compliance required for using and modifying
electronic equipment.

User Guide for Ollee Mini PC MAPMG
2
Always disconnect the computer from its power source and from any network before performing any of the
procedures described in this guide.
Failure to disconnect power or networks before you open the computer or perform any procedures can result in
personal injury and/or equipment damage. Some circuitry on the board can continue to operate even though the
front panel power button is off.
Follow these guidelines before you begin:
•Always follow the steps in each procedure in the correct order.
•Create a log to record information about your computer, such as model, serial numbers, installed options,
and configuration information.
•Electrostatic discharge (ESD) can damage components. Perform the procedures described in this chapter
only at an ESD workstation using an antistatic wrist strap and a conductive foam pad. If such a station is
not available, you can provide some ESD protection by wearing an antistatic wrist strap and attaching it to
a metal part of the computer chassis.
Installation Precautions
When you install and test the Ollee Mini PC, observe all warnings and cautions in the installation instructions.
To avoid injury, be careful of:
•Sharp pins on connectors
•Sharp pins on circuit boards
•Rough edges and sharp corners on the chassis
•Hot components (such as SSDs, processors, voltage regulators, and heat sinks)
•Damage to wires that could cause a short circuit
Observe Safety and Regulatory Requirements
If you do not follow these instructions, you increase your safety risk and the possibility of noncompliance with
regional laws and regulations.
This guide tells you how to:
•Change/install an M.2 SSD
•Change/install a 2.5-inch drive
It also includes the specifications for the MAPMG and MAPMG1.

User Guide for Ollee Mini PC MAPMG
3
Open the Ollee Mini PC Chassis
To open the Ollee Mini PC chassis, follow these steps:
1. With a plastic removal tool (or similar tool) remove the front plastic cover.
2. With a screwdriver unscrew the five front panel screws. Then slide the front cover and PCB from the
aluminium chassis.

User Guide for Ollee Mini PC MAPMG
4
Changing an M.2 SSD
The Ollee Mini PC MAPMG supports a 42mm M.2 SSD (M.2-2242).
To Change an M.2 SSD:
1. Remove the small screw from the 42mm metal standoff on the board.
2. Align the space at the bottom of the new M.2 SSD to the key on the connector.
3. Insert the bottom edge of the M.2 SSD into the connector.
4. Secure the card to the standoff with the small screw.

User Guide for Ollee Mini PC MAPMG
5
Changing a 2.5” SSD or Hard Drive
The Ollee Mini PC MAPMG supports an additional 2.5” Solid State Drive (SSD) or Hard Disk Drive (HDD).
To add a 2.5”SSD or HDD:
1. Unscrew the 4 screws attaching the drive bay to the PCB.
2. Screw the 2.5” drive into the drive bay.

User Guide for Ollee Mini PC MAPMG
6
3. Slide the drive bay and attached 2.5” disk into the SATA connector on the Mini PC ensuring the disk is fully
seated into the SATA connector.
4. Secure the storage bracket onto the PCB with the four screws that were used in step 1).

User Guide for Ollee Mini PC MAPMG
7
Close the Chassis
1. After all components have been installed, slide the Ollee Mini PC assembly into the aluminium chassis and
screw in the 5 retaining screws.
2. Attach the new face plate using the included adhesive tape.

User Guide for Ollee Mini PC MAPMG
8
Specifications
Carton Barcode
9421029871050
Barcode
9421029871029
Model No
MAPMG
Description
Ollee Ultra Mini Smart Cloud PC (Win10 Pro)
4GB/32GB
General
Brand
Ollee
Series
Ultra MINI Range
Model
MAPMG
CPU Supported
CPU Type
7th Generation Intel Celeron N3350
1.1 GHz to 2.4 GHz Turbo, Dual Core
2MB cache, 6W TDP, 14nm
Memory Supported
Memory Installed
4GB DDR3L-RS
Max Memory Supported
4GB
Expansion Slots
Other
M.2 2242 slot for SATA III SSD
2.5" SATA III
Storage
eMMC
Sandisk (or Toshiba) 32GB eMMC
2.5" SATA III
No drive installed
M.2 (2242) SATA III
No SSD installed
Graphics
Onboard Video
Intel® HD Graphics 500
200MHz to 650MHz Turbo, 12EU's
Open GL, Quick Sync, clear Video HD
Intel AI inference acceleration
Support for three simultaneous displays
Audio
Channel
Intel Smart Sound Technology
Realtek HD Audio (SST)
2 channel, 16-bit, 192000 Hz
Communications
LAN
Realtek PCIe GBE
MAX LAN Speed
10/100/1000Mbps
Wireless LAN
Intel Dual Band Wireless-AC 3165
802.11ac, 2.4 GHz & 5 GHz
Bluetooth
Bluetooth Version 4.2

User Guide for Ollee Mini PC MAPMG
9
Extension Bays
2.5" Internal Bays
9.5mm
Front Panel Ports
2 x USB3.0
2 x USB2.0
Back Panel Ports
HDMI
Type A, V1.4, 4K @30Hz
VGA
15 pin VGA connector
Ethernet
RJ45
Audio input
3.5mm TRS
Audio output
3.5mm TRS
Power
3.5mm
Power Supply
Input
12V DC
Power Supply
12V 24W power supply with US plug
Features
Features
Intel Apollo Lake Platform - Customer
Reference Design
Microsoft Windows 10 Pro
Trusted Platform Module 2.0
Silent fan less design
Device
Dimension
165x155x30mm (6.5" x 6.1" x 1.2")
Weight
700g (1.54lbs)
Packaging Unit
Dimension
269 x 200 x 55mm (10.59" x 7.87" x 2.16")
Weight
1.2kg (2.65lbs)
Inner
N/A
Master Carton
Qty per Carton
10 units per carton
Dimension
555 x 280 x 220mm (21.85" x 11" x 8.66")
Weight
12.1kg (26.67lbs)