Olympia HT 430-22 User manual

User Manual
HT 430-22
Programmable energy-saving radiator
thermostat
V1.15
08/22
ID:73024
User manual
Please read the user manual before you
place the thermostat. Keep the
documents for later questions and
provide them if you pass the thermostat
on to other persons.
Scope of delivery
1 HT 430-22 energy saving radiator
thermostat
1 User manual
1 Connector
3 Adapters (Danfoss RA, Danfoss RAV,
Danfoss RAVL)
2 batteries (mignon, AA)
Application as directed
By purchasing the HT 430-22 energy saving
radiator thermostat you own a programmable
radiator thermostat which can be used for
temperature regulations in enclosed rooms
and therefore, it can contribute to the
reduction of heating energy. –Please use the
thermostat only for this purpose. The
programming port is intended ONLY for our
programming stick. Never connect other
devices with the programming port!
The Programming stick can be found on:
www.addliving.com
Set up menu
By pressing MENU, you will arrive at the
set up menu. Please choose one of the
items with the selector wheel. With OK
you can select one menu item and with
the selection wheel they can be adjusted.
The button OK confirms the setting. The
button MENU leads to the previous level.
MODE Select the mode
AUTO = automatic mode
MANU = manual mode
PROG S etting of time program
TEMP S etting of comfort and economy
temperature
ZEIT Setting of date and time
FENS Window function
RES Reset of the device to factory
preset
ADAP Starting of a new adaptation to
adjust the valve
URLA T ravel function
INST I nstallation function (Please only
attach the controller to the coupling ring in
this position)
OFFS A daptation of temperature to the
room situation
STBY Standby mode
VERS version
DST Daylight saving time
Display and control elements
1
Union nut
2
Heating times
3
AUTO or MANU mode
4a
MENU –Opens the main menu
(starting from the standard display);
within a menu, navigate one step
back by pressing the button
4b
OK – Confirm
4c
TIME –Timer function
5
Adjusting wheel
6
Key lock
7
Battery low
8a
Vacation function
8b
Comfort temperature
8c
Energy-save temp.
8d
Frost protection function
9
Battery compartment
10
USB-Port
Inserting / replacing batteries
Remove the battery lid by pressing the
battery lid upwards (1) at the highlighted
point and then taking it out (2).
(2)
Then insert the batteries as represented in the
appliance. Do not use accumulators! Ensure
that the polarity is correct!
Safety information regarding handling
batteries
Warning! Risk of suffocation through
batteries.
• Keep batteries out of reach of children.
• Seek medical attention immediately if
one is swallowed.
Caution! There are different risks involved
when dealing with batteries.
• Never attempt to recharge standard
batteries, never short circuit batteries
and/or open batteries. Doing so leads to a
potential risk of overheating, fire or
explosion.
• Improper handling of
batteries/rechargeable batteries can
endanger your health and the
environment. Batteries/rechargeable
batteries may contain toxic and
environmentally harmful heavy metals
(Cd = cadmium, Hg = mercury, Pb = lead).
Therefore, hand in used batteries at a
municipal collection point. Therefore,
separate disposal and recycling of spent
batteries is essential for the environment
and health.
• Ensure the connection terminals are not
short-circuited.
• Never throw batteries into a fire or
water.
• Never expose batteries to any
mechanical loads.
• Leaking batteries could cause damage to
the device. If a battery should start to leak,
remove it from the device immediately to
prevent any further damage. Take the
utmost care when handling damaged or
leaking batteries and always wear
protective gloves.
• Avoid any contact with the skin, eyes,
and mucous membranes. Rinse any parts
of the body which have encounter battery
acid with plenty of clean water and
contact a doctor immediately. Avoid
extreme conditions and temperatures
which could affect the batteries, e.g. by
placing them on radiators or exposing
them to direct sunlight.
• Only use batteries of the type specified.
• Never use batteries of different types or
new and old batteries together.
• Ensure batteries are inserted with the
correct polarity.
• If the device will not be used for a longer
period, switch the device off and remove
the batteries.
• Remove empty batteries from the
device and dispose of them according to
the applicable directives.
• The batteries must be removed from the
device before its disposal.
• You are legally obliged to dispose of
batteries at your dealer or at the collection
points provided by the responsible waste
disposal authority.
Setting date and time
After inserting the batteries for the first
time the date will flash on the display.
Now, date and time can be set.
Set date with the selector wheel. Confirm
with OK .
Set month with the selector wheel.
Confirm with OK .
Set day with the selector wheel. Confirm
with OK .
Set hour with the selector wheel. Confirm
with OK .
Set minute with the selector wheel.
Confirm with OK .
–That’s it.
On the display PREP . will be shown. Now, the
motor will completely move to the installation
position to make the installation easier. As
soon as HT 430-22is ready for installation. INST
will be shown on the display ( INST - any time
selected in the menu).Now please do notpress
any other buttons! Plug device for coupling
ring.
→ see mounting.
The HT 430-22 automatically switches to
daylight saving time.
You can also set date and time via the
menu item later on. But in case of that, HT
430-22 does not move to the installation
position.
→ In case of replacing batteries, the
stored time programme will remain
active. You should check the specifi ed
time to ensure that.
Mounting
HT 2000 can be quickly and easily mounted on all
common valves (see adapter table). It can be
installed without grime and water spots because
the heating circuit is not interrupted.
1. Turn the manual thermostat head up
completely, loosen the
1. fastening and pull the thermostat off
the valve.
2. Use an appropriate adapter, if required,
and push it onto the valve.
3. Screw the connector on the valve or the
adapter.
4. Now, you put HT 2000 on the connector
until it noticeably clicks into place.
ATTENTION : It must be possible to insert the
device without applying force, ensure that the
appliance is in the INST or EIN position.
→ In case of a later installation, please
switch in the menu to INST before you
install the device. Herewith the
installation is facilitated. Only mount it in
this position.
Dismounting
To remove HT 430-22, remove this at the
EIN (with the wheel turn on the highest
temperature of over 28 C° to EIN position),
wait for a short period and unscrew the
cap nut and remove the device from the
valve.
Adaptation
Initial installation: Press the button OK
until ADAP appears on the display so that
HT 430-22 will be able to start its
adaptation. The device will adapt itself to
the stroke of your valve body. To do this
the valve will now be opened and closed
several times to store the end points. In
some cases, this process can take a few
minutes. After successful adaptation it
returns to normal mode.
- Should adaptation become necessary
again, e.g., if your radiator does not cool
down in the -Position, please press in
the menu the button until adaptation
starts again.
- If the mistake is shown on the display
place HT 2000 onto the radiator valve
and then take the batteries out for a
short time to execute a reset.
Adapter
Heimeier,
Junkers
Landys+Gyr,
MNG, Honeywell,
Braukmann
Gewindemaß
von M 30x1,5
No adapter
required.
Danfoss RAV
( accompanying pin
mustbe pluggedon
the valve tapped)
Danfoss RA
Danfoss RAVL
NOTE: Use the enclosed letter and nut
with Danfoss RA/RAV.
Please remove the marked connecting rods
completely before mounting the adapters!
Basic operating modes
MANU-Modus
In the MANU-mode HT 430-22 adjusts to the
manually specified temperature.
AUTO-Modus
In the AUTO-mode HT 430-22 changes
between to temperatures according to
the time program that has been set:
Comfort temperature (factory preset
21°C)
Economy temperature (factory preset
16°C)
The heating and economy times can be
specified via the adjustable time program . It is
possible to set 8 switch points (4 heating and 4
economy times) per day at the most. HT 430-
22 has the following factory preset:
Heating time:
Heating with comfort temperature
(factory preset: 1st heating time at 07:00)
Economy time:
L owering to economy temperature
(factory preset: 1st economy time at 22:00)
Setting heating and economy times:
With HT 430-22 it is possible to set 4 heating
and 4 economy times per day –one for each
day or one for a block of several days. TAG1 to
TAG7 represent the weekdays from Monday to
Sunday. Additionally, the corresponding days
are shown as abbreviation below the menu bar
on the display .
Block construction:
T 1–5 = same program from Monday - Friday
T 1–6 = same program from Monday -
Saturday
T 1–7 = same program from Monday - Sunday
→ For non-programmed days the factory
preset remains active .
Setting of an individual program:
Press MENU . Select the menu item PROG
with the selector wheel. Press OK. TAG1
for Monday is shown on the display. Select
day/block with the selector wheel.
Confirm with OK .
Set the beginning of the 1
st
heating time
(symbol ) with the selector wheel.
Confirm with OK . Set the beginning of the
1
st
economy time (symbol ) with the
selector wheel. Confirm with OK . Now, if
desired, a 2
nd
, 3
rd
or 4
th
heating/economy

time can be entered.
→ If you do not want to set a further
heating/economy time confirm „– ––“ with
OK .
T he next dayfor programmingis shown on the
display.
→ If you do not want to enter a further day,
leave the menu with MENU .
If the temperature is shown on the display the
programmingis finished. Within the blocks you
can also overwrite single days with differing
times .
Setting comfort and economy temperature
Press MENU . Select the menu item TEMP
with the selector wheel. Confirm with OK .
Set comfort temperature with the selector
wheel. Confirm with OK . Set the economy
temperature with the selector wheel.
Confirm with OK .
Area OFF: 8°C, freeze protection is activated
Area ON : valve is completely open
By the way : Maximum energy saving can
be obtained with an economy
temperature which is about 5 °C below
the comfort temperature.
Manual operation
With the selector wheel an adaptation of
the room temperature is possible at any
time. In the AUTO mode it remains active
until the next switch point is reached.
Now, the usual program becomes active
again
Further functions
Timer function
The timer function is selected with the
timer-button . With this function a user-
defined temperature for a programmable
period can be entered. This can be very
useful in case of a party, for example.
Press first, the time for which the time
program has been deactivated is shown.
Confirm with OK Now, the desired
temperature can be set. Confirm with OK.
In the selected period it is not possible to
change the temperature manual, the
wheel is locked. Press Menu and unlock it.
Offset
If the perceived temperature significantly
differs from the set thermostat
temperature a temperature set up can be
executed. Press MENU Select the menu
item OFFS with the selector wheel.
Confirm with OK . The degree setting 0,0°C
will flash on the display. Now, set up the
desired adaptation for the temperature
(from -5 up to +5°C) with the selector
wheel.
Confirm your entry with OK . The
temperature display does not change!
Window function
If you open a window and consequently the
temperature drops significantly, HT 430-22
will automatically close the heating valve to
save energy. The display will show .
Afterwards, the device will resume normal
operation. For the set up select FENS in the
menu. Confirm with OK First, the sensibility is
selected with the selector wheel ( HIGH = high
sensibility, MID = medium sensibility (factory
preset), LOW = low sensibility). Confirm with
OK . Now, you enter the time (10 min (factory
preset) - 60 min) for which the valve should
remain closed. Confirm with OK .
Travel function
For the time you are absent you can
select an individual temperature. After
this period the originally defined program
becomes active again.
Press MENU . Select the menu item URLA .
Confirm with OK (suitcase appears on
the display). Select with the selector
wheel the end of the travel function (=
date of the recommencement of the
regular heating times). Confirm with OK .
Set the time and confirm with the button
OK . The signal AUS appears on the
display. Now set the temperature and
confirm with OK . appears on the
display. With MENU the function can be
deactivated.
Child lock
You can lock HT 430-22 to protect the device
from unauthorized activation. Press the
buttons OK + at the same time for about 2
seconds until the signal appears on the
display to lock the device. By using this button
combination again, the symbol disappears, and
you release the lock.
Heating pause –Closing the valve
Press MENU . Select the menu item MODE
with the selector wheel. Confirm with OK .
Select MANU and confirm with OK . Set
the temperature on the display to AUS .
The valve is now closed and will work
without a time program. The calcification
protection function remains active once a
week. After the heating pause you switch
in the menu to the AUTO-mode and the
personally set program will be executed
again.
Daylight saving time
Press MENU . Select DST with the selector
wheel. Confirm with the OK button and
select ON / OFF with the selector wheel.
HT 430-22 switches automatically from
summer to wintertime.
LCD standby indicator
Press MENU . Select the menu item STBY
with the selector wheel. Confirm with the
OK button and select EIN / AUS with the
selector wheel. After about 30 seconds,
the LCD indicator switches into standby
mode. By pressing any button, the display
will be activated again. (by removing the
battery, standby mode will be reseted).
Increases the battery lifetime.
Going back to factory preset / All reset
Press MENU . Select the menu item RES
with the selector wheel. Confirm with OK .
OK flashes, confirm with OK . HT 430-22 is
reset again. Now, proceed as described for
the initial operation.
Freeze protection and calcification
protection function are active
automatically:
Freeze protection function
If the temperature drops below 6°C, HT
430-22 opens the valve until the
temperature again rises above 8°C. This
prevents the radiators from freezing.
Calcification protection function
To prevent radiator valves from calcifying
HT 2000 is submitted to calcification
protection program once a week on Friday
mornings.
Technical data
We reserve the right to make technical
changes for the purpose of improvement.
Model
HT 430-22
Supply voltage
3 V
Max. power
consumption
100 mA
Batteries
2 x Mignon, 1,5 V
Display
LCD
Dimensions
74 x 65 x 54 mm
Weight (incl. adapter
and batteries)
191 g
Connection
M30 x 1,5 mm
Ambient
temperature
5 to 55°C
Surface temperature
max. 90°C
(at the radiator)
Linear stroke
4,3 mm
Cleaning
To clean the HT 430-22 use only a dry or
lightly wet cloth. Avoid chemical solvent
–it can probably damage the device.
Disposal:
Find out about the
possibilities of taking back
old appliances and used
batteries free of charge
from your dealer.
The adjacent symbol
indicates laws dictate that
electrical and electronic
apparatus no longer required
must be disposed of separate
from domestic waste.
Dispose of your device at a
collection point provided by
your local public waste
authority. Packaging
materials must be disposed
of according to local
regulations.
Defective or empty batteries
must be recycled in
accordance with Directive
2006/66/EC and its
amendments. Return
batteries and the device via
the collection points
provided.
Packaging materials must be
disposed of according to local
regulations.
Observe the identification on
the packaging materials
during the waste sorting
process; they are identified
by abbreviations (b) and
numbers (a) which have the
following significance: 1–7:
plastic/20–22: paper and
cardboard/80–98: composite
materials.
Warranty
Dear customer,
We are delighted that you have chosen
this equipment.
In the case of a defect, please return the
device together with the receipt and
original packing material to the point of
sale.
Manufacturer
GO Europe GmbH
Zum Kraftwerk 1
D-45527 Hattingen
Germany
www.go-europe.com
Legal notice
Trademarks or trade names used in these
operating instructions are in all cases the
property of the respective owner of the
rights.
Declaration of Conformity
The full EU Declaration of
Conformity is available online
at the following website or by
scanning the QR code:
http://productip.com/?f=1645
9f
Help
Problem
Cause
Solution
Batteries do not have enough power.
Replace batteries.
Heating element does not
warm up.
Is the boiler water temperature, O.K.?
Valve does not open, is it calcified after the
summer pause /heating pause?
Adjust the temperature of the boiler water.
Remove the HT 430-22, move the valve stem
back and forth per hand or with a tool.
Heating element does not
cooldown.
Valve does not close completely. It may be
that the closing point of your valve seat has
shifted.
Adapt again (see “Adapting”) Move the valve
stem several times by hand, it may be that
adaptation is impossible because your valve is
calcified or the seat no longer performs its
function.
Pressure piece falls out
(This can also cause
an E1-error)
Due to an endless thread the pressure piece,
which is situated at the bottom, can fall out if
the device has not been affixed on the valve
Put in the pressure piece. The device can be
adapted by pressing the MENU point or by
removing and inserting the batteries. The
endless thread is rotating now and fixes the
pressure piece again. Just install it to the
radiator and adapt it once again.
E1-E3
By pressing any key, the error message will be deleted in the display and the adapter is restarted.
E1
No adaptation possible.HT 430-22 is not
installed to the heater.
Is the installation, OK?
Install HT 430-22 to the heater.
E2
Valve stroke is too short.
Open and close the valve several times manually
or replace the batteries.
E3
Motor movement is not possible.
Does the valve stem move freely?