Omega GPS-D4500 User manual

Model:
GPS-D4500
Installation And Testing Guide
Write the VIN (Vehicle Idencaon Number) on the mirror
hanger/acvaon card included with this system.
Choose a discreet yet ideal locaon for the module (the large
white label must face towards the sky because the GPS and cel-
lular antennas are built in.
Route wiring and make all necessary wiring connecons and
apply power to the module - SEE THE WIRING DIAGRAM IN THIS
BOOKLET.
Move the vehicle outside so the module has a clear view of the
sky and leave the vehicle’s ignion in ON/RUN posion.
Aer approximately 3 minutes, check the indicator lights to make
sure the unit has cellular service and has a GPS lock. Both the yel-
low and orange lights should be on solid.
Call the Omega GPS operaon center at 800-307-0680 to perform
the installaon test. Be sure to have the serial number and VIN
available.
Complete the installaon by reassembling the vehicle’s interior.
IMPORTANT: Be sure to hang the mirror hanger/acvaon card
or give it to the vehicle’s owner. The device cannot be acvated
without this informaon
Quick Reference Install Guide
1
2
3
4
5
6
7
8
VEHICLE TRACKING & RECOVERY SYSTEM
Detailed instructions cont’d on following pages ->
IM_GPS-D4500 r1 9/30/09

2
Step 1: Record Vehicle Info On Activation Card
The activation card is the bottom part of the mirror hanger included with
this system. It should already have a sticker with the serial number on it. Be sure
this serial number matches the serial number on the device being installed.
This will prevent unnecessary troubles later during the testing process.
Example of the serial number sticker:
Be sure to write a check mark to next each of the features listed on the
card. Note: Output #3 is not applicable to this device. This information helps the
vehicle’s owner understand what their system can and cannot do preventing any
future confusion.
 FindtheVehicleIdenticationNumber(VIN)andwriteitontheactiva-
tion card. The VIN can be found in the vehicle’s door jam or can be seen through
the lower corner of the windshield. it is a 16 digit alpha-numeric number. If the
device is being used on something other than a passenger vehicle, write
down the machine’s serial number instead.
Serial Number
Step 2: Determine a mounting location
Find a discreet and secure mounting location for the module. Make sure
the module is free from moisture, excessive heat, direct sunlight, or moving
vehicle parts.
- The large white sticker must be facing towards the sky
- There cannot be any metal between the module and the sky
- Mount as high in the dash as possible
- Mount at least 12 inches away from the radio and speakers. The cellular portion
of this device could cause radio interference.
- DO NOT SECURE THE DEVICE YET
Step 3: Wiring Connections
Identify which wires are needed for this particular installation and sepa-
rate the needed wires from the unneeded wires. You can cut away any excess
wires and be sure to tape or cap the ends of unused wiring. Route the wiring
away from any moving parts or anything that could generate excessive heat.
MAKE ALL CONNECTIONS BEFORE PLUGGING IN THE MODULE!!!
BLACK Ground wire (PIN 15; in long black sheath; required):
This provides chassis ground to the device. It should be connected
directly to the metal structure of the vehicle. Strip the end of the wire and crimp
on the supplied ring terminal. Route this wire to a solid grounding point, like an

3
existing bolt in the vehicle and securely ground the wire.
BLUE and RED Starer Interrupt wires (from relay socket; optional):
These wires are used the interrupt the vehicle’s starter circuit in a vehicle
theftscenario.Locatethevehicle’sstarterwire(typicallyfoundintheignition
switchharness).Itwillshow+12VwhentheignitionkeyisturnedtotheSTART
position. Cut the starter wire and connect the BLUE and RED wires to each side
of the cut wire. These are not polarized so it does not matter which side is used.
YELLOW Unlock output wire (PIN 11; optional):
This is a negative pulse output typically used to unlock the vehicle’s
doors.Ithasa0.25second,250mAoutput.Dependingonthevehicle,arelay
or doorlock interface may be required. Be sure to study the vehicle’s doorlock
system before making this connection. This connection is determined by the
vehicle’s design.
VIOLET Alarm trigger input (PIN 3; optional):
Thisisaninputtodetectwhenthevehicle’salarm(factoryoraftermar-
ket)istriggered.Thisgeneratesthenoticationtotheendusertoalertthemof
the violation. This input must see pulses and can detect a positive or negative
input.Itmustsee10pulses(20polaritychanges)within30secondstoactivate
thenotication.Connectthiswiretothepulsinghornoutputofthealarm.Ifa
hornoutputisnotavailable(typicallywithaftermarketalarms),youcanconnectit
totheashinglightscircuit.
BROWN Ignition wire (PIN 8; 18ga; fused; required):
This wire monitors when the ignition is turned ON/OFF. Connect this wire
toa+12Vignitioncircuitwhichcanbefoundintheignitionswitchharness.Be
surethisshows+12VwhenthekeyisintheONandSTARTpositionsONLY.
RED Constant power wire (PIN 14; fused; in sheath; required):
This is the power supply wire to the device. It must be connected to a
constant+12Vsource.Thiscanbefoundintheignitionswitchharness,afuse-
block,oratthevehicle’sbattery.Becertainthatthiswirehas+12Vunderall
circumstances and when the ignition key is in the ON and OFF positions.
BEFORE CONNECTING, remove the 3 amp fuse from the RED wire.
ALL REMAINING WIRES ARE NOT USED FOR THIS DEVICE
Step 4: Move the vehicle outside
You must move the vehicle outside and make sure the device has a
“clear view of the sky” before applying power. This will ensure the quickest initial
GPS lock and the best cellular coverage.
IM_GPS-D4500 r1 9/30/09

4
Step 5: Apply power to the device
You can now plug the molex connector/wiring harness into the module
andinsertthe3ampfuseintotheREDpowerwire.Also,besuretheignitionkey
isintheON/RUNposition(thisputsthedeviceinfullpowermodetoensurecon-
nectivity).
Step 6: Check the indicator lights
Locate the indicator lights on the end of the module. They are next to the
main connector. If everything is as desired, after a few minutes, you will notice
theYELLOWandORANGEindicatorlightswillashtheneventuallyturnon
solid. Solid lights indicate proper connectivity and you can proceed to the installa-
tion test.
ORANGE light (cellular connectivity):
8Off: No power, the cellular radio is OFF.
8Blinking: The cellular radio is searching for service
4Solid: Cellular service has been found with good signal strength
YELLOW light (GPS connectivity):
8Off: No power or the ignition key is OFF, the GPS receiver is OFF.
8Blinking: The GPS receiver is searching for satellite connectivity
4Solid: GPS lock has been made with multiple satellites
Step 7: Test installation and activation
You Must Call 800-307-0680 Or The Owner Cannot
Use This Device!!
Be sure to have the activation card on hand with all the information de-
scribed in STEP 1. This phone call will only take a few minutes and is very impor-
tant to verify that the device is operating properly. Follow the prompts for testing
the installation and a live representative will walk you through the process.
ONCE THE TEST IS SUCCESSFUL, BE SURE TO HANG THE MIRROR
HANGER/ACTIVATION CARD ON THE MIRROR OR HAND IT DIRECTLY TO
THE END USER WHEN THE INSTALL IS COMPLETE. THEY WILL NEED
THIS INFORMATION TO ACTIVATE THE DEVICE FOR SERVICE.
Step 8: Complete the installation
 Aftersuccessfullycompletingtheinstallationtest,securelymountthe
module in the selected location with tie straps, high grade hook & loop tape, or
any other reliable mounting method, and reassemble the vehicle’s interior.
ONCE AGAIN, BE SURE THAT THE END USER IS GIVEN THE ACTIVATION CARD.

5
P/N: ESN: III|||IIIIIIIIIII||IIIIIIIIIIII ICC-ID: 1234567890987654 IIIIIIIIIII|||||||||||IIII||||IIIIII|I|||||||II |||II||| FCC ID: QIPTC65 IC ID: 267W-TC65 CEID: 0682 IMEI: IIIII |||IIIIIIIIII||||||||||||IIIIIIIIIIIIIIIIII|| This device complies with part 15 of the FCC Rules. Opera- tion is subject to the condition that this device does not cause harmful interferece. Assembled in USA
-D4500
Wiring Overview
Indicator lights
ORANGE: NOT USED YELLOW: (-) Unlock Output VIOLET: (+/-) Alarm trigger Input
Starter
Interrupt
Relay
Starter Motor
8
YELLOW:
NOT USED
GREEN: (-) Starter Kill Output
BROWN: (+) Ignition Input
Ignition Switch
BROWN: (+) Ignition Input
Vehicle
Battery
- + RED: (+) Constant +12V Input
FUSE
FUSE BLACK: (-) Chassis Ground Input
IM_GPS-D4500 r1 9/30/09

6
Useful Information
OmegaGPS
Activation Phone Number: 800-307-0680
Login Website: www.OmegaGPS.com
Omega Research & Development, Inc.
Corporate Website: www.CarAlarm.com
Corporate Phone: [phone]
Install Tech Support (hardwire/wiring only): 800-921-TECH (8324)
Service Tech Support: 800-307-0680

7
BLANK PAGE
IM_GPS-D4500 r1 9/30/09

8
BE SURE THAT THIS
ACTIVATION CARD
IS GIVEN TO THE
VEHICLE OWNER. THEY
CANNOT ACTIVATE
THEIR SERVICE WITHOUT
THIS INFORMATION
4
4
4
4
Unlock Doors
N/A
1234567890123456
BE SURE TO FILL OUT
ALL THE INFORMATION
ON THE BACK OF THE
CARD (see the example to
the right). IT HELPS THE
VEHICLE OWNER
UNDERSTAND WHAT
THE SYSTEM WILL DO
FOR THEM AND GIVES
THEM A POSITIVE
IMPRESSION OF YOU
AND YOUR COMPANY!
IM_GPS-D4500 r1 9/30/09