Page 3
In order to mount the iConverter tabletop module to the shelf, the optional wall mount
brackets (4381) must be installed on the module.
Shelf with iConverter Standalone Wall Mount Modules
5) Installing iConverter 2-Module Chassis
Up to two iConverter 2-Module chassis can be mounted on the shelf.
In order to mount the iConverter 2-Module Chassis to the shelf, the optional wall mount
brackets (model 8249-0) must be installed on the chassis (not included).
Shelf with iConverter 2-Module Chassis
NOTE: Mounting the 2-Module chassis to the shelf requires 2U rack spacing.
6) Installing iConverter GM4 5-Port and 1-Module Chassis and OmniConverter /S
Up to three OmniConverter /S or 10G Multi-rate or iConverter GM4 5-Port or 1-Module
Chassis can be mounted on the shelf.
In order to mount the iConverter 1-Module Chassis to the shelf, the optional wall mount
brackets (model 8249-0) must be installed on the chassis (not included).
Shelf with OmniConverter /S and iConverter 1-Module Chassis
7) Installing RuggedNet Switches and Extender, and OmniConverter Switches
Up to two RuggedNet switches or Extenders or OmniConverter Switches can be mounted
on the shelf.
Shelf with OmniConverter Switches
In order to mount a RuggedNet switch to the shelf, the optional wall mounting plate (model
8260-3) must be installed on the switch (not included).
General and Copyright Notice
This publication is protected by U.S. and international copyright laws. All rights reserved. The whole or any part of this publication
may not be reproduced, stored in a retrieval system, translated, transcribed, or transmitted, in any form, or by any means, manual,
electric, electronic, electromagnetic, mechanical, chemical, optical or otherwise, without prior explicit written permission of Omnitron
Systems Technology, Inc.
The following trademarks are owned by Omnitron Systems Technology, Inc.: FlexPointTM, FlexSwitchTM, iConverter®, miConverterTM,
OmniConverter®, RuggedNet®, Omnitron Systems Technology, Inc.TM, OSTTM and the Omnitron logo.
All other company or product names may be trademarks of their respective owners.
The information contained in this publication is subject to change without notice. Omnitron Systems Technology, Inc. is not responsible
for any inadvertent errors.
Warranty
This product is warranted to the original purchaser against defects in material and workmanship for a period of two (2) years from
thedateofshipment.ALIFETIMEwarrantymaybeobtainedbytheoriginalpurchaserbyregisteringthisproductwithinninety(90)
days from the date of shipment at www.omnitron-systems.com/support. During the warranty period, Omnitron will, at its option, repair
or replace a product which is proven to be defective with the same product or with a product with at least the same functionality.
For warranty service, the product must be sent to an Omnitron designated facility, at Buyer’s expense. Omnitron will pay the shipping
charge to return the product to Buyer’s designated US address using Omnitron’s standard shipping method.
Limitation of Warranty
The foregoing warranty shall not apply to defects resulting from improper or inadequate use and/or maintenance of the equipment
byBuyer,Buyer-suppliedequipment,Buyer-suppliedinterfacing,unauthorizedmodicationsortamperingwithequipment(including
removalofequipmentcoverbypersonnelnotspecicallyauthorizedandcertiedbyOmnitron),ormisuse,oroperatingoutsidethe
environmentalspecicationoftheproduct(includingbutnotlimitedtovoltage,ambienttemperature,radiation,unusualdust,etc.),or
improper site preparation or maintenance.
Nootherwarrantyisexpressedorimplied.Omnitronspecicallydisclaimstheimpliedwarrantiesofmerchantabilityandtnessfor
any particular purpose.
The remedies provided herein are the Buyer’s sole and exclusive remedies. Omnitron shall not be liable for any direct, indirect, special,
incidental, or consequential damages, whether based on contract, tort, or any legal theory.
Environmental Notices
The equipment covered by this manual must be disposed of or recycled in accordance with the Waste Electrical and Electronic
Equipment Directive (WEEE Directive) of the European Community directive 2012/19/EU on waste electrical and electronic equipment
(WEEE) which, together with the RoHS Directive 2015/863/EU, for electrical and electronic equipment sold in the EU after July 2019.
Such disposal must follow national legislation for IT and Telecommunication equipment in accordance with the WEEE directive: (a)
Do not dispose waste equipment with unsorted municipal and household waste. (b) Collect equipment waste separately. (c) Return
equipment using collection method agreed with Omnitron.
The equipment is marked with the WEEE symbol shown to indicate that it must be collected separately from other types of
waste. In case of small items the symbol may be printed only on the packaging or in the user manual. If you have questions
regarding the correct disposal of equipment go to www.omniton-systems.com/support or e-mail to Omnitron at intlinfo@
omnitron-systems.com.
©2022 Omnitron Systems Technology, Inc. 040-08260-001E 5/22
Omnitron Systems Technology Inc. * 38 Tesla * Irvine, CA 92618
949.250.6510 tel * 949.250.6514 fax * www.omnitron-systems.com
