OMT-Veyhl OV1015 User manual
OV1015
HEIGHT ADJUSTABLE WORKSTATION
USER GUIDE
OV1015 | Part No. 84981
User Guide: OV1015
2 | OV1015
OV1015
HEIGHT ADJUSTABLE WORKSTATION
Transform your home and ofce into true ergonomic workspaces.
The OV1015 height adjustable workstation has clean, modern lines
and is simple to use. OV1015 provides electric height adjustability,
single or dual monitor support, VESA mount capability, integrated
wire management, BIFMA compliance and all steel construction.
Solid, made with quality and built here in the USA.
PRODUCT OVERVIEW
FEATURES
• Single and dual monitor congurations
• Electric lift
• Integrated wire management
• Tools provided for easy assembly
• Two color options
• Rated for 67 lb. total weight
35 lb. load (tray) and 32 lb. (monitor mount)
OV1015 | 3
User Guide: OV1015
Parts Diagram 4-5
Workstation Unit 4
Hardware Kit 5
Safety Information 6-7
Assembly Instructions 8-15
Operation 16
Initialization and Reset 16
Handswitch Operation 16
Troubleshooting 17
Unit Errors 17
Handswitch Errors 17
Technical Data 18
Standards & Certications 19
Customer Service 19
Warranty & Returns 19
TABLE OF CONTENTS
TABLE OF CONTENTS
This manual explains how this sit-stand workstation is assembled, used, and
maintained. All sit-stand workstations are subjected to functional and quality tests
before leaving our facility.
User Guide: OV1015
4 | OV1015
OV1015
PARTS DIAGRAM
PARTS DIAGRAM
11 12
14
4
13
1
7
8
2
9
5
3
10
6
PARTS Qty/Package
1. Clip Cord Manager 2
2. M6x1.0 20mm Button Head Screw 4
3. M6x1.0 10mm Flat Head Screw 2
4. M6x1.0 12mm Flange Button Head Screw 2
5. M8x1.25 20mm Flat Head Screw 3
6. M6x1.0 12mm Thumb Screw
(dual attachment only) 2
7. Motor Box 1
8. Universal Desktop Angle Foot 2
9. Desktop Tray 1
10. Mounting Bracket (Dual) 1
11. Mounting Bracket (Single) 1
12. X Bracket (dual attachment only) 2
13. Wire Management Bracket 1
14. Column 1
OV1015 | 5
User Guide: OV1015 PARTS DIAGRAM
PARTS Qty/Package
1. Clip Cord Manager 2
2. M6x1.0 20mm Button Head Screw 4
3. M6x1.0 10mm Flat Head Screw 2
4. M6x1.0 12mm
Flange Button Head Screw 2
5. M8x1.25 20mm Flat Head Screw 3
6. Bumper Pads 10
7. 5mm Allen Wrench 1
8. 4mm Allen Wrench 1
HARDWARE KIT CONTENTS
4
1
6
2
3
5
8
7
User Guide: OV1015
6 | OV1015
SAFETY INFORMATION
SAFETY
INFORMATION
INSTALL ONLY ON STABLE WORK SURFACES
Install on stable surfaces with entirety of legs and motor box supported.
KEEP AWAY FROM CHILDREN
This unit is not designed for use in areas accessible by small children. For indoor use only.
BE CAREFUL WHEN ADJUSTING WORKSTATION HEIGHT
Body parts and property can be caught between the moving work surface and an immobile obstacle
(such as shelves, furniture, window sills, or walls). Keep at least one inch of clearance around workstation
and make sure nothing is in workstation’s path for its entire range of motion.
Before raising or lowering:
• Check surroundings on all sides of workstation are clear
• Make sure corded objects will not be pulled off workstation or cause other objects to fall
• Make sure workstation power cord moves freely as tray moves up and down
IMPORTANT SAFETY INSTRUCTIONS Save these instructions.
DANGER
To reduce the risk of electric shock:
Always unplug this furnishing from the electrical outlet before cleaning.
WARNING:
To reduce the risk of death, serious injury, or property damage, read and
follow this safety information and the provided instructions when assembling this product.
Do not change or replace components and accessories provided by OMT-Veyhl.
OV1015 | 7
User Guide: OV1015 SAFETY INFORMATION
DO NOT OVERLOAD DESK
To prevent workstation from tipping or collapsing, make sure the tray is not overloaded by the weight of
objects on tray. Evenly distribute load; excess loads near edges can reduce stability and lead to tip over.
• Do not exceed maximum load of 35 lb. (16Kg) on tray
• Do not sit or stand on table
USE CARE WHEN MOVING WORKSTATION
• Clear objects and equipment from workstation before moving to reduce the risk of tipping over.
• Adjust the workstation to its lowest height before moving
• To disconnect, turn all controls to the off position, then remove plug from outlet
• Do not move a loaded workstation
• Do not lift the workstation by the tray
DO NOT OPEN ELECTRICAL COMPONENTS
Do not attempt to service components. There are no user-serviceable parts inside the motor control units
or legs. If your workstation needs service, contact customer service. Never operate this furnishing if
it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged. Return the
furnishing to a service center for examination and repair.
KEEP WORKSTATION DRY
Keep all electrical components away from water and high humidity. Clean only with a dry or
slightly damp cloth. Do not spray cleaning solutions directly onto workstation.
GROUNDING INSTRUCTIONS
This product is equipped with a cord having an
equipment-grounding conductor and a grounding plug.
Use only the cord provided. Make sure that the product
is connected to an outlet having the same conguration
as the plug (as shown in Illustration A) that is properly
installed and grounded in accordance with all local
codes and ordinances.
Do not modify the plug provided with the product
– if it will not t the outlet, have a proper outlet
installed by a qualied electrician.
No adapters are to be used with this product.
Keep cord away from heated surfaces.
Grounded
Outlet
Grounded Outlet Box
Grounding
Pin
Grounded
Outlet
Grounded Outlet Box
Grounding
Pin
ILLUSTRATION A
User Guide: OV1015
8 | OV1015
ASSEMBLY INSTRUCTIONS
ASSEMBLY
INSTRUCTIONS
ASSEMBLY OVERVIEW 1. Attach rubber pads to motor box and feet
2. Assemble the feet to the motor box
3. Attach rubber pads to tray
4. Assemble the tray to the column
5. Attach the monitor bracket to the column
6. Mount the monitor(s) to the monitor bracket
7. Install the monitor(s)
8. Attach clip cord manager
9. Attach wire management bracket
10. Connect to power
If you have any difculty assembling this unit, or need to order
replacement parts, please contact our Customer Service department.
Use the parts diagrams on page 4-5 as a reference.
The assembly of the workstation to be made in accordance with this manual.
Changes to the workstation or improper use may affect the safety, function, and life of your product.
This manual is for the OV1015 Height Adjustable Workstation.
OV1015 | 9
User Guide: OV1015 ASSEMBLY INSTRUCTIONS
ATTACH RUBBER PADS TO MOTOR BOX AND FEET
Attach two of the provided rubber pads to the corresponding
bottom anges on the motor box.
Attach two rubber pads to the underside of the forward-facing
section of each foot.
1
1
9
1
10
User Guide: OV1015
10 | OV1015
ASSEMBLY INSTRUCTIONS
ASSEMBLE THE FEET TO THE MOTOR BOX
Lay column assembly on it’s back as shown in diagram above. Insert the base feet
tabs into the corresponding slots on the column base. Insert angled feet into column
base as shown. Fasten each foot to the column base with the M6x1.0 20mm button
head screws. Fully tighten screws with the provided 4mm Allen wrench.
2
1
11
Internal parts removed for better view
7
3
10
9
ATTACH RUBBER PADS TO TRAY
Attach two bumper pads to the underside of the tray as shown below.
Pads should be placed on at surface inward from corner weld.
3
OV1015 | 11
User Guide: OV1015 ASSEMBLY INSTRUCTIONS
ASSEMBLE TRAY TO COLUMN
With the column assembly still on its back, attach the desktop tray to the column
assembly by setting the tray between the base feet. Using the M8x1.25 20mm at
head screws and the 5mm Allen wrench, secure the tray to the column assembly.
4
8
6
11
User Guide: OV1015
12 | OV1015
ASSEMBLY INSTRUCTIONS
WARNING:
Serious damage may occur
to the functionality of your Ascend by
using the wrong screws. ONLY USE zinc
plated M6x1.0 10mm at head
screws to attach monitor bracket.
(Shown to size)
ATTACH THE MONITOR BRACKET TO THE COLUMN
Using the M6x1.0 10mm at head screws provided in the hardware kit, attach the
monitor mounting bracket to the column using one of the four attachment positions.
Make sure to test the location of the bracket before installing and use
the attachment position that best ts your height requirements.
For Single Monitor, see Figure 1
For Dual Monitor, see Figure 2
FIGURE 1
FIGURE 2
5
OV1015 | 13
User Guide: OV1015 ASSEMBLY INSTRUCTIONS
MOUNT THE MONITOR TO THE MONITOR BRACKET
Single Monitor: Line up the four slots on the monitor mounting bracket with the VESA spaced mounting
holes on the back of your monitor. Using four M4 screws that came with your monitor, secure the monitor
to the mounting bracket. See Figure 1
Dual Monitor: Line up the four slots on the X bracket with the VESA spaced mounting holes on the back
of your monitor. Using four M4 screws that came with your monitor, secure the X bracket in place.
See Figure 2
Note that some monitors may have inset mounting locations and will require spacers to be placed in
between the back of the monitor and the mounting bracket.
FIGURE 2FIGURE 1
6
User Guide: OV1015
14 | OV1015
ASSEMBLY INSTRUCTIONS
ATTACH CLIP CORD MANAGER
Attach the clip cord managers to the back of the column assembly
and route the monitor cords through the clip cord managers.
Be sure to leave enough slack in cords to account
for workstation in raised position.
8
(DUAL MONITOR ONLY)
INSTALL THE MONITORS
Slide the monitors onto the dual monitor mounting bracket via the openings in the
previously attached X brackets. Position the monitors in the desired locations and
secure in place using the provided M6 thumb screws. Be sure not to over tighten
the thumb screws (only 6-7 turns should be sufcient to lock the monitors in place).
7
OV1015 | 15
User Guide: OV1015 ASSEMBLY INSTRUCTIONS
CONNECT TO POWER
Enjoy your new OV1015 Height-Adjustable Tabletop Workstation!
ATTACH WIRE MANAGEMENT BRACKET
With the cords routed in the back side of the column, attach the wire
management bracket using two M6x1.0 12mm ange button head screws.
Do not over-tighten (hand-tightening is sufcient).
Top ange of wire management bracket can be bent by hand if it doesn’t
sit ush with the back side of the column.
9
10
User Guide: OV1015
16 | OV1015
OPERATION
INFORMATION
INITIALIZATION/RESET
The workstation may need to be initialized/reset after any of the following:
- After assembly
- After disconnection from the power supply
- After any impact on the tray.
To initialize/reset, you will need to move the workstation to the lowest position by holding the DOWN button of
the handswitch until the column reaches the lowest position. Then press the DOWN button again and hold it
pressed for ve seconds or until a slight movement of the workstation drops down to the machine zero point
and back up to the operation zero point. Once the tray stops moving, release the DOWN button. If the button
is released too early, this leads to a malfunction of the workstation and you must repeat the reset process.
The upper height position is programmed into the control box. For this reason, only use the control box that
has been provided with the specic table frame. Under no circumstance should a control box from one
workstation be moved to another.
HANDSWITCH OPERATION
By pressing the UP or DOWN buttons, the workstation will move up or down to the desired position.
Once the desired position is reached, let go of the UP or DOWN button. The tray will stop once it reaches
the lower or upper height position.
OPERATION INFORMATION
OV1015 | 17
User Guide: OV1015 OPERATION INFORMATION
TROUBLESHOOTING
UNIT
ERROR
SOURCE SOLUTION
Workstation
does not move
No power supply Plug in the power cord or check the connection
on the control box
No connection or a loose
connection to the drives
Verify the plug connection of the motor cable
to the control box
No connection or a loose
connection to the handswitch
Verify the plug connection of the motor cable
to the control box
Max lifting capacity
is exceeded
Reduce the weight or load on the tray
Replace the handset
Max time limit is exceeded Control is activated automatically after approx. 9 minutes
Defective drive Contact customer service
Defective control box Contact customer service
Handset is defective
Workstation
moves down at
a slow rate
Control box expects
new reset Reset control box. (See page 16)
If it is not possible to resolve an error as described, disconnect the power cord, wait a few minutes and reset
the table again. If the error still occurs, remove the table from the power source and contact customer service.
(Error Code list is valid from rmware 1.7.5 and higher)
User Guide: OV1015
18 | OV1015
GENERAL CONTROL BOX
Power supply 120 VAC ±10% / 60 Hz
Standby power consumption, primarily <0.3 W
Operating temperature 0-35°C
Protection class IP 20
Maximum power output 216VA/24V
Travel speed 1.5"/sec
Maximum tray capacity 35 lb.
Stroke length 18.9"
Maximum monitor size compatibility 24" screens
TECHNICAL DATA
TECHNICAL DATA
[26in]
660.4mm
[35.2in]
893.87mm
[44.6in]
1133.5mm
[24in]
610.91mm
OV1015 | 19
User Guide: OV1015 CUSTOMER SERVICE
If you have any problems with
your product, please contact
our service department.
PHONE: 1-616-738-6688
FAX: 1-616-738-6682
CONTACT YOUR SALES REPRESENTATIVE FOR WARRANTY INFORMATION
WARRANT Y
The drive system is tested according to the following standards:
CSA C22.2#68
Issued: 2009/09/01 Ed: 7 (R2014)
Motor-Operated Appliances (Household and Commercial);
Gen. Inst. No.1: 2010, Gen. Inst. No.2: 2010
STANDARDS & CERTIFICATIONS
CUSTOMER SERVICE
End of life cycle: Once product is disassembled, all steel components can be recycled at your local
metal collector. For products with electronic components, see Disassembly Guide.
OV1015
USER GUIDE
Part No. 84981
Rev 021618
Table of contents
