Oncam Evolution 05 Instruction Manual

Evolution 05 Mini Camera Range
Installation & User Manual
© Oncam Global Group AG, 2013 - 2016. All rights reserved.
EVO-05-L#D-06, Rev B
December 2016

Installation & User Manual –Oncam 360°Evolution 05 Mini Camera Range
December 2016
© Oncam Global Group AG, 2013 - 2016. All rights reserved.
2
Manual Copyright
© Oncam Global Group AG, 2013 - 2016. All rights reserved.
No part of this manual may be reproduced except for your express personal use.
Oncam and their affiliate’s further reserve the right to alter, amend or revise this document and
any product specifications without any obligation to provide notice of such changes.
Oncam and its affiliates make no guarantee, representation or warranty, either expressed or
implied, regarding the accuracy of the information contained in this manual. Furthermore, Oncam
and its affiliates assume no responsibility or any potential liability for any errors that may appear
in this manual.
Trademarks and Third‐Party Copyrights
Oncam and the Oncam logo are registered trademarks of Oncam Global Group AG.
Oncam and the IPZoom logos are trademarks of Oncam Global Group AG (and its affiliates).
SATIV is a service mark of Oncam Global Group (and its affiliates).
The names of other companies, organizations, products or services mentioned in this manual are
the trademarks of their respective owners.
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not immerse in water. Protect the connectors from moisture.
6. Do not block any ventilation openings, Install in accordance with the manufacturer’s
instructions.
7. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
8. The polarity of any connector attached to the product should be verified before connection.
9. Protect all cables from being crushed or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
10. Only use attachments / accessories specified by the manufacturer.
11. Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been dropped.
WARNING
RISK OF EXPLOSION IF REPLACING A BATTERY WITH
AN INCORRECT BATTERY TYPE

Installation & User Manual –Oncam 360°Evolution 05 Mini Camera Range
December 2016
© Oncam Global Group AG, 2013 - 2016. All rights reserved.
3
Contents
1Overview ...............................................................................................................................................................................................5
1.1 Fisheye View.........................................................................................................................................................................................5
1.2 Panoramic View ....................................................................................................................................................................................5
1.3 Camera Range......................................................................................................................................................................................5
1.4 Power Requirements ............................................................................................................................................................................5
2Camera Placement and Orientation......................................................................................................................................................6
2.1 Ceiling Mount ........................................................................................................................................................................................6
2.2 Wall Mount ............................................................................................................................................................................................6
2.3 Table Mount ..........................................................................................................................................................................................7
2.4 Coverage Area......................................................................................................................................................................................7
2.5 Overhead Viewing Angle ......................................................................................................................................................................7
2.6 Lighting..................................................................................................................................................................................................7
3Camera Installation ...............................................................................................................................................................................8
3.1 Preparation............................................................................................................................................................................................8
3.2 Indoor & Indoor Night Cameras ............................................................................................................................................................8
3.3 Panel-Mount Camera..........................................................................................................................................................................10
3.4 Recessed Camera ..............................................................................................................................................................................11
3.5 Outdoor Camera .................................................................................................................................................................................13
3.6 Outdoor Pendant Camera Kit..............................................................................................................................................................14
3.7 Accessories.........................................................................................................................................................................................16
4Camera Mounts ..................................................................................................................................................................................17
4.1 Wall Mount ..........................................................................................................................................................................................17
4.2 Corner Mount ......................................................................................................................................................................................19
4.3 Pole Mount..........................................................................................................................................................................................20
5Dome Handling and Cleaning .............................................................................................................................................................21
6First Time Operation ...........................................................................................................................................................................22
6.1 DHCP ..................................................................................................................................................................................................22
6.2 Static IP Installation ............................................................................................................................................................................22
6.3 Finding Available Cameras .................................................................................................................................................................22
6.4 Assigning an IP Address.....................................................................................................................................................................23
6.5 Connecting to the Camera ..................................................................................................................................................................23
6.6 Media Player Requirements................................................................................................................................................................23
7Camera Web Interface........................................................................................................................................................................24
7.1 Control Panel ......................................................................................................................................................................................24
7.2 Image ..................................................................................................................................................................................................25
7.3 Administration .....................................................................................................................................................................................28
7.4 Regions...............................................................................................................................................................................................41
8Connecting Directly to the Camera Streams ......................................................................................................................................44
8.1 JPEG Snapshot ..................................................................................................................................................................................44
8.2 MJPEG / H.264 Video Stream ............................................................................................................................................................45
9Connecting through ONVIF Profile S or PSIA ....................................................................................................................................45
10 Troubleshooting and Technical Support .............................................................................................................................................46
10.1 Contact................................................................................................................................................................................................46
10.2 Revision History ..................................................................................................................................................................................46
11 Copyright and Legal Notices...............................................................................................................................................................47

Installation & User Manual –Oncam 360°Evolution 05 Mini Camera Range
December 2016
© Oncam Global Group AG, 2013 - 2016. All rights reserved.
4
12 Additional Online Resources...............................................................................................................................................................48
12.1 Technical Specifications .....................................................................................................................................................................48
12.2 Oncam 360-degree Viewer.................................................................................................................................................................48
12.3 OnVu360 Mobile Application (iOS and Android).................................................................................................................................49
13 Frame Rate, Resolution & Storage Requirements .............................................................................................................................50
14 NVR and Storage Partners .................................................................................................................................................................50
List of Figures
Figure 1 Indoor Camera Exploded View ...............................................................................................................................................................9
Figure 2 Panel-Mount Camera Exploded View...................................................................................................................................................10
Figure 3 Recessed Camera Exploded View .......................................................................................................................................................11
Figure 4 Outdoor Camera Exploded View ..........................................................................................................................................................13
Figure 5 Outdoor Pendant Camera Kit Exploded View.......................................................................................................................................14
Figure 6 Wall Mount Exploded View ...................................................................................................................................................................17
Figure 7 Corner Mount Exploded View ...............................................................................................................................................................19
Figure 8 Pole Mount Exploded View...................................................................................................................................................................20
Figure 9 Oncam Grandeye Camera Configuration Tool .....................................................................................................................................22
Figure 10 Color Hysteresis Curve .......................................................................................................................................................................26
Figure 11 Administration Settings .......................................................................................................................................................................28
Figure 12 Network Settings.................................................................................................................................................................................29
Figure 13 Alarm Settings Triggers ......................................................................................................................................................................30
Figure 14 Alarm Settings Actions........................................................................................................................................................................31
Figure 15 Alarm Settings Actions –E-Mail .........................................................................................................................................................32
Figure 16 Alarm Settings Actions –FTP.............................................................................................................................................................32
Figure 17 Alarm Settings Actions –Record to microSD-Card ............................................................................................................................33
Figure 18 Camera Settings –MJPEG.................................................................................................................................................................33
Figure 19 Camera Settings –H.264 ...................................................................................................................................................................34
Figure 20 Clock Settings .....................................................................................................................................................................................34
Figure 21 Stream Settings ..................................................................................................................................................................................35
Figure 22 Recordings Dialog...............................................................................................................................................................................37
Figure 23 Camera Configuration Tool –Reset to Factory Defaults....................................................................................................................39
Figure 24 Factory Reset Button ..........................................................................................................................................................................40
Figure 25 Region Settings...................................................................................................................................................................................41
List of Tables
Table 1 Main Camera Stream Maximum Frame Rates ......................................................................................................................................36
Table 2 Main and Second Camera Maximum Frame Rates...............................................................................................................................36

Installation & User Manual –Oncam 360°Evolution 05 Mini Camera Range
December 2016
© Oncam Global Group AG, 2013 - 2016. All rights reserved.
5
1 Overview
The Oncam Evolution 05 Mini IP Series cameras are innovative and use a fisheye lens to create
a 360° view with an extremely large area of coverage. The Oncam 360° IP camera may replace
two or more conventional fixed cameras for seamless coverage of an entire scene with no gaps
or blind spots. The ability to see in all directions at once makes Oncam 360° IP cameras ideally
suited for total situational awareness.
The 5‐megapixel sensor produces enough detail to allow digital pan/tilt/zoom (PTZ) operations
over the entire field of view (FoV). Unlike conventional PTZ cameras, Oncam 360° IP cameras
are silent. Oncam 360° IP cameras have no mechanical motors or gears prone to wear and
failure. The camera produces three types of views, each suited to a particular set of
requirements.
The Evolution 05 Mini design allows for easy and fast installation with a range of mounting
accessories for ceilings, walls, pendants and poles.
1.1 Fisheye View
The high quality fisheye lens produces a spherical image from which derive all other views. The
raw image appears warped around a central axis. Special dewarping software built into the
NVR / VMS converts the spherical image into a flat view that is more familiar to human viewers.
When using video management software (VMS) to record a fisheye video stream, the entire
image is preserved. You can retrospectively look at all directions regardless of the live or
recorded viewed area after an incident.
1.2 Panoramic View
When using compatible VMS or NVR software integrated with the Oncam dewarping SDK, it is
possible to generate a double 180-degree panoramic view from fisheye overview. The fisheye
image is dewarped and split into two 180-degree bands for simpler viewing of the overall
image.
Note: Due to the dewarping image cropping, the area directly underneath the camera is not
visible. The camera does not generate the 180-degree panoramic view. The camera requires a
compatible client machine with software to produce this panoramic view.
1.3 Camera Range
Configure the camera module for either an H.264 or MJPEG single stream.
10 FPS (maximum) with a frame size of 2144 x 1944 pixels (4 MP)
15 FPS (maximum)with a frame size of 1488 x 1360 pixels (2 MP)
30 FPS (maximum) with a frame size of 1056 x 960 pixels (1 MP)
30 FPS (maximum) with a frame size of 528 x 480 pixels (1/4 MP)
Enable and configure a second H.264 fisheye stream. If enabling the second stream, the
maximum frame rates are reduced for both the main and second stream.
Simultaneously access a third MJPEG stream at a fixed FPS and a frame size of 528 x 480
pixels (1/4 MP).
1.4 Power Requirements
Supply power using IEEE 802.3af Power over Ethernet (PoE) through the RJ45 or M12 cable.

Installation & User Manual –Oncam 360°Evolution 05 Mini Camera Range
December 2016
© Oncam Global Group AG, 2013 - 2016. All rights reserved.
6
2 Camera Placement and Orientation
Camera placement is an important factor when planning your deployment. The Evolution 05 Mini
camera has an exceptionally wide viewing angle. Consider the camera location for providing
comprehensive coverage of a wide area. Mount the camera with an unobstructed view and
consider scene optimization when one portion of the scene is bright and another dark.
The camera supports three different mounting orientations, Ceiling, Wall and Table. Each of
these options require correct orientation settings selected from the Camera Web Interface. These
camera settings ensure using the correct dewarping algorithm when connecting to a compatible
VMS or NVR system.
2.1 Ceiling Mount
Ceiling mounting is preferred when most
of the action is occurring below the
camera in a horizontal plane. When a
person is directly below the camera,
captured is the top‐of head view. When
the person moves away from the
camera, more of their face and body
becomes visible.
Depending on the use case, use a single
camera to cover a small to medium sized
room. Mounting a camera high gives
great situational awareness throughout a
large room. When planning coverage
ensure there are no obstructions. Some
obstructions include pillars, high-sided
furniture and any hanging objects near
the camera such as signage.
2.2 Wall Mount
Wall mounting the camera can give a
complete 180-degree side on view of an
area. Use this view where ceiling
mounting is not possible or if you need to
capture a higher level of detail for objects
closer to the camera (such as people’s
faces as they walk past the camera).

Installation & User Manual –Oncam 360°Evolution 05 Mini Camera Range
December 2016
© Oncam Global Group AG, 2013 - 2016. All rights reserved.
7
2.3 Table Mount
Install the Table Mount camera on a flat
surface looking up. This configuration is
for demonstration or testing purposes.
You could use the Table Mount for
inspecting systems or viewing under
vehicles.
2.4 Coverage Area
The Evolution 05 Mini cameras provide coverage for open areas where situational awareness
of people and objects are required.
The higher camera placement provides a larger coverage area. However, with higher camera
placement a reduction in the pixel density is expected. Height impacts the image detail
available, therefore ensure you consider image quality versus the mounting height.
Perform tests to ensure that the camera meets the system operational requirements and the
required detail level is available.
Use a minimum height of 2 m (6.5 ft.) when ceiling mounting a camera for best results.
For multiple camera layouts, ensure the camera areas overlap for full coverage.
2.5 Overhead Viewing Angle
Ceiling‐mounted cameras capture a top‐of‐head shot when the person is directly under the
camera. Hats extend that top-of‐head zone to some degree. Consider the viewing angle when
requiring people identification or recognition.
2.6 Lighting
Avoid bright light sources pointing towards the camera lens. Always face lighting away from the
camera or above the camera installation line (if ceiling mounted).
Adjust the auto-sensor in the camera from the Web Interface. Using auto-sensor adjusts the
camera continuously to optimize the image by increasing exposure time. Furthermore, the
maximum frame rate is reduced as exposure time increases. The image remains in full color
until below one Lux, after which it transitions to black and white for better contrast.
The Indoor Night camera automatically switches to night mode, doubling the exposure time in
progressive steps to maximize light sensitivity. The frame rate is halved accordingly. The image
is rendered in black and white for better contrast. Optionally, use motion‐sensing lights to
illuminate the scene: The Indoor Night camera quickly adjusts when lights turn on.

Installation & User Manual –Oncam 360°Evolution 05 Mini Camera Range
December 2016
© Oncam Global Group AG, 2013 - 2016. All rights reserved.
8
3 Camera Installation
For installation of your Oncam Evolution 05 camera, provided are the following instructions.
Reference the Camera Web Interface, page 24 for a more detailed features and functionality.
3.1 Preparation
Document the camera’s location and MAC address for camera configuration. Find the MAC
address on a sticker on the side and rear of the camera module.
3.1.1 Inserting an microSD card
Configure a microSD card for recording alarm-triggered
events. The microSD card slot is located on the edge of
the camera module.
Compatible SD cards
microSD, microSDHC, microSDXC
Up to 128 GB maximum capacity
The camera uses the format EXT3, while most microSD
cards use the format FAT32. Therefore, it is necessary
to format the microSD card to EXT3 prior to using the
first time.
Use the camera to format the microSD card for an EXT3 file system using the Camera Web
Interface. See Recordings, page 37.
In addition, you may use a computer to format several microSD cards for an EXT3 file system.
While additional software is required, this method may be faster.
3.2 Indoor & Indoor Night Cameras
The Evolution 05 Mini Indoor camera is designed for
quick and easy installations. Install the Mini Indoor
camera anywhere a professional lightweight
enclosure is required. A range of mounting
accessories includes an IK10 vandal-proof cover
and pendant mount adapter.
Use the enclosure for indoor use in surface mount
installations. The indoor camera consists of the
polymer base and cover.
The Evolution 05 Mini Indoor camera comes fitted
with an RJ45 flying lead for connectivity to data and
PoE.
NOTICE: The Indoor Night camera requires an 850 nm infrared light source and passes visible,
and near infrared light (850 nm).

Installation & User Manual –Oncam 360°Evolution 05 Mini Camera Range
December 2016
© Oncam Global Group AG, 2013 - 2016. All rights reserved.
9
Two Torx screws attach the cover to the base.
Figure 1 Indoor Camera Exploded View
3.2.1 Parts List
Camera Module
Torx Screwdriver Bit
Mounting Kit
Drilling Template
Quick Start Guide
3.2.2 Installation Steps
NOTICE: Do not over-tighten the Torx screws. Only hand tighten.
1. Prepare the surface by using the supplied drilling template. Drill holes appropriately sized
for the two base holes for use with mounting hardware.
NOTICE: Use the hardware appropriate for the surface material that collectively supports at
least four times the weight of the camera.
2. Loosen the two cover screws using the Torx tool bit and remove the trim cover.
3. Attach the camera module to a wall or ceiling surface using the two base holes.

Installation & User Manual –Oncam 360°Evolution 05 Mini Camera Range
December 2016
© Oncam Global Group AG, 2013 - 2016. All rights reserved.
10
4. Route the network cable through the mounting plate cable routing canal to allow concealed
cable access from the rear or side of the enclosure.
5. Reattach the trim cover to the camera base and apply power.
6. Remove the screen protection.
For mounting options, see Camera Mounts, page 17.
3.3 Panel-Mount Camera
The Evolution 05 Mini Panel Mount camera provides quick and easy installations in shallow
areas requiring the EN50155/EN45545 transport certification. The panel mount camera comes
with an RJ45 or M12 plug and spans a 108 mm (4.25-inch) diameter. Install the Mini Panel
camera behind thin flat surfaces of 1 to 3 mm (.04 to .12-inch) thickness, such as walls or
ceilings.
Figure 2 Panel-Mount Camera Exploded View
3.3.1 Parts List
Camera Module
Torx Screwdriver Bit
Mounting Kit
Drilling Template
Quick Start Guide

Installation & User Manual –Oncam 360°Evolution 05 Mini Camera Range
December 2016
© Oncam Global Group AG, 2013 - 2016. All rights reserved.
11
3.3.2 Installation Steps
NOTICE: Do not over-tighten the Torx screws. Only hand tighten.
1. Prepare the surface by using the supplied drilling template. Drill holes appropriately sized
for the three base holes and center clearance hole.
2. Loosen the three cover screws from the front plate using the Torx tool, removing the front
plate.
3. Position the camera behind the panel surface with the fisheye lens protruding through the
center hole, aligning the surrounding three holes.
4. Reattach the front plate to the camera using the three Torx screws. The panel is
sandwiched between the front plate and the camera.
5. Apply power and remove the screen protection.
3.4 Recessed Camera
The Evolution Mini Recessed camera allows for easy and fast internal installation from below
the ceiling line. The camera is IP40-rated and UL2043 certified for installation in air handling
spaces.
The Evolution 05 Mini Recessed camera provides recessed mounting in drop ceilings or walls
with a maximum cross section of 25.4 mm (1-inch).
Remove the camera's trim cover and paint the cover to blend with your installation environment.
Figure 3 Recessed Camera Exploded View

Installation & User Manual –Oncam 360°Evolution 05 Mini Camera Range
December 2016
© Oncam Global Group AG, 2013 - 2016. All rights reserved.
12
3.4.1 Parts List
Camera Module
Quick Start Guide
RJ45 Coupler
Drilling Template
3.4.2 Installation Steps
1. Using the drilling template, cut a 108 mm (4.25-inch) mounting hole.
2. Connect the Ethernet coupler to the network infrastructure cable. Pass any spare cable
length through the hole into the ceiling before fitting the camera.
3. Connect the camera and confirm the LED lights illuminate when powered.
4. Push both retaining springs to an upright position and insert the camera into the hole.
5. Release the springs and gently push the camera into position.
6. Carefully remove the lens protection film.

Installation & User Manual –Oncam 360°Evolution 05 Mini Camera Range
December 2016
© Oncam Global Group AG, 2013 - 2016. All rights reserved.
13
3.5 Outdoor Camera
Surface mount the Mini Outdoor camera to a flat surface, such as a wall or ceiling. The
Evolution 05 Mini Outdoor model consists of the Camera module that is Polymer base and
outer cover with an IK10-rated optical bubble.
The camera module is supplied fitted with a flying lead with either an RJ45 socket or an M12
plug. This provides connectivity for data and Power over Ethernet (PoE). The cover comes
fitted with two stainless steel Torx security screws to fix it to the base module.
Figure 4 Outdoor Camera Exploded View
3.5.1 Parts Supplied
Camera Module
Torx Screwdriver Bit
Mounting Kit
Drilling Template
Quick Start Guide
3.5.2 Installation Steps
NOTICE: Do not over-tighten the Torx screws. Only hand tighten.
1. Using the drilling template, drill holes sized for the mounting hardware and network
connector pigtail.
2. Loosen the screws with the Torx screwdriver bit.
3. Carefully remove the trim cover, ensuring the gasket is not damaged or removed.
4. Secure the camera base to a wall or ceiling with the appropriate mounting hardware. Pull
the cable through the mounting surface.
5. Realign the front cover to the base, ensuring the Gore vent holes are aligned with the side
arrow.
6. Fasten the Torx screws, installing the protective caps.
For mounting options, see Camera Mounts, page 17.

Installation & User Manual –Oncam 360°Evolution 05 Mini Camera Range
December 2016
© Oncam Global Group AG, 2013 - 2016. All rights reserved.
14
3.6 Outdoor Pendant Camera Kit
The Mini Outdoor Pendant Camera Kit is intended for compatible wall, pole or pendant mount
brackets. The Outdoor Pendant Camera Kit consists of an RJ45 camera module and a
preassembled Pendant Mount Assembly (Sunshield, Back Box and thread adapter).
The RJ45 flying lead provides connectivity for data and Power over Ethernet (PoE).
Figure 5 Outdoor Pendant Camera Kit Exploded View
3.6.1 Parts Supplied
Camera Module
Drilling Template
Pendant Mount Assembly
Torx Screwdriver Bit
Quick Start Guide
Spanner
3.6.2 Preparation
1. Remove the two dome cover screws using the Hex Screwdriver Bit.
2. Carefully remove the dome cover and set aside.

Installation & User Manual –Oncam 360°Evolution 05 Mini Camera Range
December 2016
© Oncam Global Group AG, 2013 - 2016. All rights reserved.
15
3.6.3 Installation Steps
NOTICE: Do not over-tighten the Torx screws. Only hand tighten.
1. Using the drilling template, drill holes sized for the
mounting hardware.
2. For concealed cable entry, also drill the cable
clearance hole.
3. Pass the unterminated network cable through the
cable gland at the top of the pendant assembly.
4. Tighten the cable gland using the supplied
spanner.
5. Align the camera base to the Pendant Mount
assembly and twist into place.
6. Secure the Pendant Mount assembly into the
bracket or mounting pole.
7. To ensure the cable does not twist, do not rotate
the lower part of the Pendant Mount Assembly.
8. Using the Hex Screwdriver, fully tighten the
Pendant Mount Assembly to the mounting bracket.
9. Trim the network cable to length and terminate,
securing it to the camera module.
10. Ensure the excess cable fits comfortably into the
back box of the Pendant Mount Assembly.
11. Secure the camera to the Pendant Mount
Assembly.
12. Attach the dome cover to the camera.
13. Tighten the Pendant Mount Assembly locking
screw.
14. Remove the protective dome cover film.

Installation & User Manual –Oncam 360°Evolution 05 Mini Camera Range
December 2016
© Oncam Global Group AG, 2013 - 2016. All rights reserved.
16
3.7 Accessories
Accessories are available to compliment and extend the flexibility of the Evolution 05 Mini
camera. Some are in convenient kits to make ordering easier and ensure that nothing is missing
at installation.
Camera Application
Part Number
Description
Indoor, Panel-Mount, Night
OBE-11-IWA (White)
OBE-11-IBA (Black)
IK10+ vandal resistant bubble trim
The bubble trim is made of optical
grade polymer
Indoor, Night, Outdoor
OBE-16-OWA (White)
OBE-16-OBA (Black)
M20 conduit back box
Fitted for the camera back and
provides three entry points for easy
cabling through M20 size conduits.
Coil excess cable within back box.
Indoor, Night
OBE-13-IBA
Pendant Mount Adapter
M32 female thread; supplied with
M32 to 1½ NPT male thread
adaptor. Fit onto the camera back
Indoor, Night
OBE-17-OWA (White)
OBE-17-OBA (Black)
Indoor Mounting Kit
Includes a Pendant Mount Adapter
and Conduit Back Box.

Installation & User Manual –Oncam 360°Evolution 05 Mini Camera Range
December 2016
© Oncam Global Group AG, 2013 - 2016. All rights reserved.
17
Camera Application
Part Number
Description
Outdoor
EVO-05-LWK (White)
EVO-05-LBK (Black)
The kit contains the following items
for the
EVO-05 Mini Outdoor Camera
(RJ45 option)
Pre-assembled Pendant Mount
Assembly (Sunshield, Back Box and
thread adapter)
4 Camera Mounts
The following mounting accessories are available for the Indoor and Outdoor Evolution cameras
to allow installation in multiple environments.
4.1 Wall Mount
The Wall Mount has a 1½-inch NPT female pipe thread. There is a set screw in the 1½-inch
thread area which locks the housing into a fixed rotation.
OBE-04-OWA -White
OBE-04-OBA –Black
Figure 6 Wall Mount Exploded View

Installation & User Manual –Oncam 360°Evolution 05 Mini Camera Range
December 2016
© Oncam Global Group AG, 2013 - 2016. All rights reserved.
18
The Mounting Plate is not required when mounting to a studded or solid wall where you are not
using an electrical box.
Likewise, do not use the Mounting Plate for Pole or Corner Mount installations.
1. Fasten the Mounting Clip to the wall surface using fasteners (not supplied). Ensure using
the appropriate fasteners for the wall material (capable of supporting a minimum four times
the weight of the wall mount and camera).
2. Ensure that the arrow mark on the plate is oriented up.
3. Pass the cables through one of the holes in the plate.
4. Hook the wall mount arm over the top tabs on the Mounting Clip.
5. Tighten the two set screws on the bottom, locking the arm to the Mounting Clip.
6. Pass the cables through the mount arm and out the threaded hole on the end of the arm.
4.1.1 Rough Surfaces or over Electrical Boxes
1. Fasten the Wall Mount Plate to the box or the wall surface.
2. Fasten the Mounting Clip using the two nuts and washers provided.
This provides an even surface for the Mounting Clip Plate.
CAUTION: Do not mount the camera to an electrical box where the camera would be
easily accessible. Ensure the electrical box is structurally sound to support the camera.

Installation & User Manual –Oncam 360°Evolution 05 Mini Camera Range
December 2016
© Oncam Global Group AG, 2013 - 2016. All rights reserved.
19
4.2 Corner Mount
The Corner Mount is a bracket that adapts the wall mount to fit diagonally on the corner of a
building, giving a 270° FoV at the corner. Attach to the building through four appropriate fixings
(not provided). The bracket has an opening that accommodates a conduit connection into the
back of the wall mount. The Wall Mount Mounting Clip attaches directly to the Corner Mount
bracket in the same manner as the pole mount.
OBE-05-OWA –White
OBE-05-OBA –Black
Use with the Wall Mount kit sold separately.
Figure 7 Corner Mount Exploded View
1. Fasten the Corner Mount Adapter to wall surfaces using four fasteners (not supplied).
Ensure the fasteners are appropriate for the wall material and capable of supporting at least
four times the weight of the wall mount and camera.
2. Fasten the Wall Mounting Clip to the Corner Mount adapter using the two nuts and washers
provided with the Wall Mount Kit.
Note: The Wall Mount Plate is not used.
3. If necessary, the hole in the Corner Mount Adapter accepts a flexible conduit adapter.
4. Pass the cables through the hole and into the Wall Mount Arm.
5. Fasten to the Mounting Clip.

Installation & User Manual –Oncam 360°Evolution 05 Mini Camera Range
December 2016
© Oncam Global Group AG, 2013 - 2016. All rights reserved.
20
4.3 Pole Mount
Use the Wall Mount Kit in conjunction with the Pole Mount when attaching to a light pole. In
addition, use the Pole Mount and Corner Mount to connect to the corner of a building. The Pole
mount is a bracket that attaches to a pole 100 to 150 mm (4 to 6 in.) in diameter with the
provided stainless steel clamping bands.
The Pole Mount Adapter has a hole that accommodates a conduit connection from the Wall
Mount Arm if it is necessary to protect the wires from the environment. The Mounting Clip
attaches directly to the Pole Mount Adapter in the same manner as the Mounting Plate.
OBE-03-OWA –White
OBE-03-OBA –Black
Use with the Wall Mount kit sold separately.
Figure 8 Pole Mount Exploded View
1. Fasten the Pole Mount Adapter to the pole using the two Stainless Steel Clamps.
2. Fasten the Mounting Clip to the Pole Mount Adapter using the two nuts and washers
provided with the Wall Mount kit.
Note: The Wall Mount Plate is not used.
The hole in the Pole Mount Adapter is designed to accept a flexible conduit if desired.
3. Pass through the cables into the hole and the Wall Mount Arm
4. Fastened the Wall Mount Arm to the Mounting Clip.