One Forall 3 Zapper User manual

R
Universal remote
E
F
D
I
NL
P
UK
URC-6530/31
702291

WWW.ONEFORALL.COM 2
Thank you for purchasing the ZAPPER 3 universal remote control
(URC-6532). Your ZAPPER package contains:
• The ZAPPER Remote Control
• The ZAPPER User Guide & Code Book
The User Guide & Code Book explains in simple steps how to set up
and operate your new universal remote control. You may need this
guide again in the future, so please be sure to keep it.
Your ZAPPER needs 2 new “AAA/LRO3” batteries.
Your ZAPPER is designed to let you use one remote to operate your
Television, VCR and Satellite Receiver (or Cable Converter).
About Your ZAPPER
Table of Contents
UK
PICTURE OF THE ONE FOR ALL REMOTE 3
INSTALLING THE BATTERIES 4
FEATURES AND FUNCTIONS 4
SETTING UP THE ZAPPER
Direct Set-Up 6
Search Method 8
Code Blink Out 9
CODELIST
Television 66
Videorecorders 73
Satellite Receivers 76
Cable Converters 80
ADVANCED OPERATION
Controlling Colour & Brightness 10
Scan 10
TROUBLE-SHOOTING
Helpful Hints 11

WWW.ONEFORALL.COM 3
4
23
6
5
1
7

WWW.ONEFORALL.COM 4
Installing The Batteries
The ZAPPER needs 2 new “AAA/LRO3” alkaline batteries.
1Remove the battery cover from the back of the ZAPPER by pressing
down on the tab.
2Match the batteries to the +/- marks inside the battery case, then
insert the batteries.
3Press the battery cover back into place.
See picture of the ZAPPER 3 remote on page 3.
1LED
The LED (Light Emitting Diode) will flash red when a key is pressed
to show the remote is working
2Magic
The MAGIC key is used to set up your ZAPPER and to access special
features.
3Power
The Power key turns your devices both on and off.
4Device Keys
The TV ,VCR and SAT keys select the home entertainment device to
be controlled. Pressing the TV key allows the remote to control the
functions of your Television. After pressing VCR you can operate
your Video Cassette Recorder. After pressing SAT, you can operate
your Satellite Receiver or Cable Converter.
Important notes:
- In order to avoid having to reprogram your ZAPPER after you remove
the batteries, you will need to insert new batteries within 5 minutes.
- Also, it is best that you do not use rechargeable batteries.
- On the inside of the battery compartment door you will find a
label on which to write your set-up codes after your ZAPPER is
set up for your devices. Please write down your codes for easy,
future reference.
Features and Functions

5Mute/OK
The Mute key operates the same function it did on your orginal
remote. It is also used to activate the Scan feature (page 10).
6Volume+/-, Programme +/-
The Volume and Programme keys operate just as on your original
remote control. These keys are also used to program the ZAPPER for
your devices and to control the Colour and Brightness settings of
your television (page 10).
7Video Recorder Keys
After pressing the VCR key, the Video Recorder keys operate the
functions of your Video Recorder. To prevent accidental recordings,
the Record key must be pressed twice.
WWW.ONEFORALL.COM 5

Direct Set-Up
To set up the ZAPPER for your Television, Video and Satellite Receiver (or
Cable Converter) follow the instructions below. To set up your Television:
1Find your Television code in the Set-Up Code section (page
66-80). Codes are listed by brand name. The most popular
codes are listed first. Make sure that your Television is
switched on (not in standby).
2Press and release the TV key to select the device.
3 Press and hold down MAGIC until the red light blinks
twice (it will blink once then twice).
4 Enter your 5-digit code according to the chart below.
The red light will blink twice.
5Now, aim the ZAPPER at your Television and press
POWER. If your Television switches off, your ZAPPER
should be ready to operate your device.
6Turn your device back on and try all the remote’s functi-
ons to ensure they are working properly. If the functions
do not work properly, repeat steps 1-6 using another code
listed under your brand.
7 Write the codes for your TV, VCR and SAT in the
boxes provided on page 7 and inside the battery
compartment for easy future reference.
6WWW.ONEFORALL.COM
Setting Up The ZAPPER
ONE FOR ALL
Acura
Admiral
Adyson
Agazi
AGB
Aiko
11132
122241224223313
14232
21131
31121
142311113211322
224141131412131
2233213444
TV
Volume + = 1
Volume
- =2
Programme + = 3
Programme
- =4

TV Code
VCR Code
SAT/Cable Code
(Example: To enter the Sony TV code 24432, you would press Volume(-),
Programme(-), Programme(-), Programme(+), Volume(-).
If your device does not respond to the ZAPPER after you have tried all
the codes listed for your brand, try the Search Method.
Make sure you write your correct 5 digit codes in the boxes
provided inside the battery compartment and on this page.
WWW.ONEFORALL.COM 7
Important notes:
- To set up your Video Recorder, Satellite Receiver or Cable Converter,
follow the same instructions above, only press the VCR or SAT key
during step 2.
- Some codes are quite similar. If your device does not respond or is not
functioning properly with one of the codes, follow steps 1-6 with each
code listed for your brand.
- If none of the codes listed for your brand operate your device, follow
the Search Method described in the next section. The Search Method can
be used even if your brand is not listed at all.
- Remember, to control your device after you have programmed it with
the ZAPPER, you must press the device key first (TV, VCR or SAT).
■■ ■■ ■■ ■■ ■■
■■ ■■ ■■ ■■ ■■
■■ ■■ ■■ ■■ ■■
Volume + = 1
Volume - = 2
Programme
- = 4
Programme + = 3

8WWW.ONEFORALL.COM
Search Method
If your Television, VCR, Satellite or Cable Converter does not respond to the
ZAPPER after trying all the codes listed for your brand, try searching for
your code. The Searching Method allows you to find the code of your devi-
ce by scanning through all the codes contained in the memory of the ONE
FOR ALL remote control. To search for your TV code:
1Make sure that your Television is switched on (not in
standby).
2Press the TV key on the ZAPPER.
3 Press and hold down MAGIC until the red light blinks
twice (it will blink once then twice).
4Next, press the Programme(-) key three times.
5Next, slowly alternate between TV and POWER until your
Television turns off. You may have to press these keys
many times, so be patient. Remember, you must aim the
ZAPPER at your device the entire time you are searching
for your code.
6When your device turns off, press and release MAGIC, to
store the code.
The zapper should now be ready to operate your television. Turn your tele-
vision back on and try all the remote’s functions to ensure they are wor-
king properly. If some of the ZAPPER’S commands are not operating cor-
rectly, try the search method again, you may be using the wrong code.
TV
Important notes:
- To search for the code for your VCR, Satellite Receiver or Cable Converter,
follow the same instructions above, only press the VCR or SAT key during
step 2 and 5.
- If your Video’s original remote control does not have a power key, press
PLAY instead of POWER when searching for your code.
- During step 5, you may have to press these keys many times (up to 150!),
so be patient. Remember, you must aim the ZAPPER at your device the
entire time you are searching for your code.
TV

WWW.ONEFORALL.COM 9
Code Blink Out
After you have used the Search Method, you can find out which code the
ZAPPER responded to by blinking back the code. It’s useful to know your
Television, Video, Satellite Receiver or Cable Converter code for future refe-
rence. Remember, you can only blink back your code after the ZAP-
PER is operating your device.
To blink out your TV code:
1Press the TV key on the ZAPPER.
2Press and hold the MAGIC key until the red light
blinks twice (it will blink once then twice).
3Next, press Programme(-), Programme(-),
Programme(+).
4For the first digit of your 5-digit code, press Volume + ( )
and count all the red blinks.
5For the second digit, press Volume - ( ) and count all
the red blinks.
6For the third digit, press Programme(+) and count all
the red blinks.
7For the fourth digit, press Programme(-) and count all
the red blinks.
8For the fifth digit, press MUTE and count all the red blinks.
Now you have your 5-digit code. Write your code in the boxes provided
previously and inside the battery compartment for easy, future reference.
Important note: To blink out the code for your Video Recorder, Satellite
Receiver or Cable Converter, follow the same instructions above, only press
the VCR or SAT key during step 1.
TV

10 WWW.ONEFORALL.COM
Controlling Colour & Brightness
Depending on the functions of your original remote control, the ZAPPER
may operate the colour and brightness settings of your Television.
Scan
Your ZAPPER comes with a special Scan function which lets you “scan”
through every programme available on your TV, VCR, Satellite or Cable Box.
For example, to scan the programmes on your TV:
1Aim the ZAPPER at your TV. Press the TV key. Press and
release MAGIC then press the MUTE key.
The ZAPPER will send the command to advance through
all the programmes available on your Television stopping
at each programme for about three seconds. Remember,
you must aim the ZAPPER at your device the entire time
you are using scan.
2When you find a programme you would like to watch,
simply press any key to stop the Scan feature.
Advanced Operation
then holdPressColour up =
then holdPressColour down =
then holdPressBrightness up =
then holdPressBrightness down =
TV
Note: You have 5 seconds to press the Volume or Channel keys for colour or
brightness adjustment after pressing MAGIC.
Important notes:
- To use Scan with your Video, Satellite or Cable Box, follow the same
instructions above, only press the VCR or SAT key during step 1.
- Scan may not function with devices that did not have a Programme +/- key
on the original remote control.