Optica B102; B204; B204M User manual

00P3NX053ZXSEA5
Optica HD Outdoor Bullet Network Camera
Models: B102, B204, B204M
User’s Manual
Ver1.5

1
Table of Contents
1. Overview.................................................................................................................................. 2
1.1 Features ........................................................................................................................ 2
1.2 Package Contents ......................................................................................................... 3
1.3 Dimensions.................................................................................................................... 4
1.4 Connectors .................................................................................................................... 5
2. Camera Cabling....................................................................................................................... 7
2.1 Connect Power.............................................................................................................. 7
2.2 Connect Ethernet Cable ................................................................................................ 7
2.3 Connect Alarm I/O......................................................................................................... 7
3. Installation............................................................................................................................... 8
3.1 Ceiling/Wall Mounting.................................................................................................... 8
3.2 Lens Adjustment (Vari-focal Lens only)......................................................................... 9
4. System Requirements .......................................................................................................... 10
5. Access Camera..................................................................................................................... 11
6. Setup Video Resolution........................................................................................................ 15
7. Configuration Files Export/ Import...................................................................................... 16
Appendix A: Technical Specifications........................................................................................ 17
Appendix B: Delete the Existing Optica Viewer......................................................................... 19
Appendix C: Setup Internet Security .......................................................................................... 20
Appendix D: Video Resolution .................................................................................................... 21
B102 - Quad Streams ............................................................................................................. 21
B102 - Triple Streams ............................................................................................................. 25
B102 - Dual Streams............................................................................................................... 27
B102 - Single Stream.............................................................................................................. 27
B204 / B204M - Quad Streams............................................................................................... 28
B204 / B204M - Triple Streams............................................................................................... 32
B204 / B204M - Dual Streams ................................................................................................ 35
B204 / B204M - Single Streams.............................................................................................. 36

2
1. Overview
Supported with both H.264 and MJPEG standard, the HD Outdoor Bullet
product series not only features in superior Full HD resolution for real-time
streaming at 30 fps, but also includes Optica’s many professional features to
enhance image quality & camera performance. With more computing power, the
IP Camera can provide more flexibility for users and system managers.
1.1 Features
zProgressive Scan CMOS Sensor
zQuad Streams support
zQuad Streams Compression:
H.264 Baseline / Main / High Profile + MJPEG
zMulti-language support
zTampering Alarm
zWide Dynamic Range
zRemote Zoom & Focus (Motorized Lens)*
zMotion Detection
zPrivacy Masks
zSmart Picture Quality / 3D Noise Reduction
zVertical View Mode (Image rotation by 90 derees)
zSmart IR Mode
zNetwork Failure Detection
zDay / Night (ICR)
zIR LED Module (working distance up to 25m)
zMicro SD support
zWeatherproof (IP66 International)
zSunshield
zIntegrated Mounting Bracket with Cable Management
(*) B204M Only

3
1.2 Package Contents
Please check the package contains the following items listed below.
Bullet IP Camera (Cable included)
Power Terminal Block (x1)
M4 Inner Hex Wrench (x1)
Alarm Terminal Block (x1)
Plastic Screw Anchors (×5)
M4 Self Tapping Screws (×5)
CD
(bundled software and documentation)
Quick Start Guide
Desiccant Desiccant User Guide

4
1.3 Dimensions
The IP Camera’s dimensions are shown below.

5
1.4 Connectors
The diagram below shows the IP Camera’s reset button and various connectors.
Definition for each connector will be given as follows.
All-in-one Cable
No Cable Pin Definition Remarks
1 Network (with PoE) - RJ-45 connector with LED
2 Power
(3-pin Terminal Block)
1 AC 24V-1 DC (-)
Power connection2 GND Reserved
3 AC 24V-2 DC (+)
3 Alarm
(4-pin Terminal Block)
1 ALM_DI－
Alarm connection
2 ALM_DI＋
3 ALM_DO－
4 ALM_DO＋
4 Audio I/O Pink Line In/ Mic In Two-way audio
transmission
Green Line Out
5 BNC - Analog Video Output

6
Micro SD Card Slot/ Reset Button
Follow the steps below to reach the Micro SD Card Slot, Reboot Button and
Factory Default Button on IP Camera:
Step 1:
Unscrew the screw on the Camera
Housing and remove the Front
Housing.
Micro SD Card Slot Factory Default Button Reboot Button
NOTE: Before installing, please refer to Desiccant User Guide in the
package to place the Desiccant in the Camera to prevent moisture from
condensing on IP Camera’s Glass Cover.

7
2. Camera Cabling
Please follow the instructions below to complete IP Camera connection.
2.1 Connect Power
Please refer to Section: Connectors. Alternatively, connect the Ethernet cable to
the camera’s PoE port and plug the other end of the cable into a PoE switch.
NOTE: If using PoE, make sure Power Sourcing Equipment (PSE) is in
use in the network.
2.2 Connect Ethernet Cable
Use of Category 5 Ethernet cable is recommended for network connection; to
have best transmission quality, cable length shall not exceed 100 meters.
Connect one end of the Ethernet cable to the RJ-45 connector of the IP Camera,
and the other end of the cable to the network switch or PC.
NOTE: In some cases, you may need use an Ethernet crossover cable
when connecting the IP Camera directly to the PC.
Check the status of the link indicator and activity indicator LEDs; if the LEDs are
unlit, please check LAN connection.
Green Link Light indicates good network connection.
Orange Activity Light flashes for network activity
indication.
2.3 Connect Alarm I/O
The camera equips one alarm input and one relay output for alarm application.
Please refer to the label on the alarm terminal block and connect the alarm
wiring accordingly.

8
3. Installation
Please read the instructions provided in this chapter thoroughly before installing
the IP Dome Camera.
3.1 Ceiling/Wall Mounting
The Bullet IP Camera can be installed directly on a wall or ceiling with the
integrated 2-axis adjustable Bracket Mount. Please note that the wall or ceiling
must have enough strength to support the IP Camera.
Follow the steps below to install the IP Camera:
Step 1:
Unpack the Bullet IP Camera package and take out the IP Camera.
Step 2:
Connect the Power/Ethernet/Alarm/Audio wires from ceiling or wall to the
corresponding connectors of the camera’s All-in-one Cable.
Step 3:
Fix the IP Camera’s Bracket on the
ceiling/wall with three supplied self
tapping screws
Step 4:
Use the supplied Inner Hex Wrench
and cross screwdriver to loosen the
hex bolt/screw on the side of the
Bracket Mount and the Camera
Housing to adjust the position of the
IP Camera.

9
3.2 Lens Adjustment (Vari-focal Lens only)
Step 1:
Unscrew the screw on the Camera
Housing and remove the Front
Housing.
Step 2:
Power up the IP Camera. Please refer to Section: Connectors for more
cabling installing details.
Step 3:
Access the Camera Browser-viewer for viewing images. Please refer to
Section: Access Camera for further details.
Step 4:
Adjust the Zoom/ Focus to set the desired zoom/ focal length.
Step 5:
Put the Front Housing back, and make sure it’s well attached to the Camera
Housing, and tighten the screw.