Orbit X M7QG1 User manual

Introduction
Congratulations on your new Orbit X camera.
All you need to get started can be found in
this quick guide
LED Video Light
Camera
Laser
Microphone 1
Microphone 2
Status LED
Power/Standby Button
Action Button
Light/Laser Button
Audio Jack
Micro USB
Wi-Fi Status Light
Battery Status Light

Power On - Long Press
Press and hold for 3 sec
to start the device
Power Off - Long Press
Press and hold for 3 sec
Standby - Short Press
To save battery, the device
goes into standby auto-
matically after 1 min or after
short-pressing
Let’s get started!
Starting
Pulsating
Constant
Ready For Use
Constant
Shutting Down
4 Sec Interval
Standby
The Basics

Capture and share your images
Record Video - Long Press
Press and hold for 1 sec. to
start and stop recording
Video Call - Extra Long Press
Press and hold for 5 sec.
Setup is required before
using this function. See
“configure your OrbitX”
section
Take Photo - Short Press
Press once. Keep camera
steady
Ready to Record
Pulsating
Constant
Recording
Constant
In Call
Pulsating
Calling
One Blink
Snapshot
Photo, Video and Video Conferencing

Night or day? Dosen’t matter
Laser On/Off - Long Press
Press and hold for 1 sec
Video Light - Short Press
Cycle light intensity
Light On
Laser On
Laser Off
Light MAX
Light Off
Lights and Laser

Connect it to the internet and get the job done!
OR
Congure your Orbit X
Orbit X app Collaboration X
Download the Orbit X
app on your android
phone or tablet.
The app is already
pre-installed if you
are using an Impact
X or Gravity X device.
Follow the instructions
and enjoy powerfull
features like remote
control and live video
preview.
Our Cloud Management
web page.
1) Login to
www.collaboration-x.net
or sign up for a 30 days
free Collaboration X
trial account.
2) Go to “Devices” and
select “Orbit X Quick
Setup”.

Mount your Orbit X to helmets, walls and
other equipment with the included Curved
and Flat Adhesive mounts and hardware
Attach it to everything!
OR
Mounting Your Camera
Mounting plate for
curved surfaces
(e.g. helmet)
Mounting plate for
flat surfaces
(e.g. walls)

Overview
Strong Signal
Fair Signal
Not Connected
Full Battery
Ok Battery
Low Battery
Pulsate
Constant
4 Sec Interval
Constant
Starting
Ready For Use
Standby
Shutting Down
Short Press
Long Press
Short Press
Long Press
5 sec. Press
Short Press
Long Press
Standby/Wake up
Power On/Off
Take a Photo
Start/Stop Video Rec.
Call/Hang Up Video Call
Video Light On/Max/Off
Laser On/Off
One Blink
Pulsate
Constant
Pulsate
Constant
Pulsate
Pulsate
Taking Photo
Ready To Record
Recording
Calling
In Call
Updating Software
Pairing Mode

Charging
Support
FAQs and technical support can be found
here: www.bartec-pixavi.com/support
The Orbit X has a high quality, high capacity
battery and shall only be charged using the
charger supplied with the unit. Charging the
Orbit X from 0% to 80% battery capacity
takes approximately 2hours. Charging the
remaining 80% to 100% takes 1 ½ hours.
The Orbit X should not be used/operated
during the charging process.
Marking
Factory Reset
1. Turn device off
2. Press and hold Power and Camera button
at the same time. The Status LED will turn
constant Pink.
3. Press and hold the Light button until the
LEDs on the back blink red.
4. Press and hold the Camera button to
confirm. The status LED will blink Pink.
5. The device will re-start when finished.
Software Update
The Orbit X will update to the latest
software automatically when it’s connected
to the internet. The status LED will pulsate
“Pink” when it is updating. See the
“configure your OrbitX” section to set it up.

Special Conditions For Safe Use
Ex ib parameter
Uo
Io
Po
Co
Lo
USB Interface
8.4 V
0.445 A
0.933 W
1.35 µF
3.06 µH
Headset
11.6 V
0.399 A
1.565 W
1.39 µF
20.6 µH
Audio Levels
Recycling (WEEE)
The device is compliant with the EN9650-1
standard. However, third party music
players can exceed the recommended
audio levels, and as such should be used
with caution as prolonged listening to
sound at high volumes can cause
permanent damage.
If you wish to discard the Orbit X,
please contact your dealer or
supplier. Do not throw the device
in your domestic rubbish/trash.
Integrated Laser
The Orbit X has built-in Laser functionality
for realtime collaboration and highlighting.
The laser can be controlled with the
“light-button” It uses a class 2 laser

The ambient temperature range of the Orbit X is
-20°C to + 45°C
The Orbit X shall be protected from contamin-
ation by liquid and dust; this is normally
achieved by the operator carrying the device on
their person.
The USB port may be used for charging the
equipment when in the non-hazardous area
only, using one of the following chargers
specifically supplied for use with the unit:
Deltaco part number USB-AC35M
(ambient for charging is 0ºC to 45ºC)
Ansmann part number 1001-0007
(ambient for charging is 0ºC to 45ºC)
GlobTek model number GT-41078-0505-USB
(ambient for charging is 0ºC to 45ºC)
GlobTek model number GT-41078-0506-0.4-USB
(ambient for charging is 0ºC to 45ºC)
Glob Tek model number GT*-46101-*05*-USB
(ambient for charging is 0ºC to 40ºC)
Glob Tek model number GT*-46101-*06*-USB
(ambient for charging is 0ºC to 35ºC).
The maximum input voltage (Um) from the
charger between the lines is 5.8 V. The charger
shall be approved for use in USA/Cananda
against CSA/UL 60950-1 or equivalent.
The USB port is also used for data download.
The port has been assessed with a Um of 5.8 V.
The equipment connected to the USB port shall
be approved for use in USA/Canada against
CSA/UL 60950-1 or equivalent.
Conditions For Use (CSA)

The ambient temperature range of the Orbit X is
-20°C to + 45°C
The Orbit X shall be protected from contamin-
ation by liquid and dust; this is normally
achieved by the operator carrying the device on
their person.
The USB port may be used for charging the
equipment when in the non-hazardous area
only, using one of the following chargers
specifically supplied for use with the unit:
Deltaco part number USB-AC35M
(ambient for charging is 0ºC to 45ºC)
Ansmann part number 1001-0007
(ambient for charging is 0ºC to 45ºC)
GlobTek model number GT-41078-0505-USB
(ambient for charging is 0ºC to 45ºC)
GlobTek model number
GT-41078-0506-0.4-USB
(ambient for charging is 0ºC to 45ºC)
Glob Tek model number GT*-46101-*05*-USB
(ambient for charging is 0ºC to 40ºC)
Glob Tek model number GT*-46101-*06*-USB
(ambient for charging is 0ºC to 35ºC).
The maximum input voltage (Um) from the
charger between the lines is 5.8 V.
The USB port is also used for data download.
The port has been assessed with a Um of 5.8
Vand shall be installed in accordance with
clause 12.2.1 of IEC 60079-14:2007/EN
60079-14:2008
Conditions For Use (ATEX & IECEx)

FCC/IC
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) this device
may not cause harmful interference, and (2)
this device must accept any interference
received, including interference that may
cause undesired operation.
Ce produit répond aux exigences de la section
15 de la réglementation FCC. Son fonctionne-
ment est soumis aux deux conditions
suivantes: (1) cet appareil ne doit pas causer
d'interférences nuisibles et (2) cet appareil
doit accepter toute interférence reçue, y
compris les interférences qui peuvent
provoquer un fonctionnement indésirable.

The Orbit X Camera is a radio transmitter
and receiver. It is designed and manufac-
tured not to exceed the emission limits for
exposure to radio frequency (RF) energy set
by the Federal Communications
Commission (FCC) of the U.S. Government,
Industry Canada of the Canadian
Government (IC), and recommended by The
Council of the European Union.
The exposure standard for wireless devices
employs a unit of measurement known as
the Specific Absorption Rate, or SAR. The
SAR limit set by the FCC/IC is 1.6W/kg. The
SAR limit recommended by The Council of
the European Union is 2.0W/kg. Tests for
SAR are conducted using standard
operating positions specified by the FCC/IC
with the device transmitting at its highest
certified power level in all tested frequency
bands.
For body worn operation, the Orbit X device
has been tested and meets the FCC/IC
exposure guidelines when used with an
accessory that contains no metal and that
positions the device a minimum of 10 mm
from the body. Such a device can i.e. be
BARTEC PIXAVI camera cradle.
Specic Absorption Rate Data

Orbit X
Quick Guide
Table of contents