Origen ae S21T User manual

Origen

Thank you for purchasing this Origen htpc enclosure. We recommend
that you read this user guide thoroughly before installation.
a
e
Origena
eis not responsible for any damages
due to external causes, including but not
limited to, improper use, problems with
electrical power, accident, neglect, alteration,
repair, improper installation or improper
testing.
Revision S21T.V3/03.14
Copyright © 2014 Technology.
All rights reserved
Origena
e

index
S21T specifications
S21T overview
Opening the case
Removing motherboard tray
Micro ATX standoff installation
VGA bracket/loop cable
Hard drive installation
Hard drive configuration
Touch panel software installation
Optical disk drive installation
Optical drive bezel installation
Metal sticker fitting instructions
PCB/cable reference diagram
TFT contols / menu operation
TFT menu guide
Hidden contols / features
Card reader & I/O ports
4
5
7
7
8
8
9
10
10
11
12
13
14
15
16
17
18

External dimensions (WxHXD)
Construction materials
Motherboard support
PSU support
PCI card support
Drive bays
Fan support
Expansion slots
Front I/O ports
IR support
Net weight
Available colours
TFT specification
435 x 224 x 390mm
all aluminium chassis
ATX, micro ATX, mini-ITX
ATX PSU
full size
10 x 3.5” internal drive bays
1 x 5.25” external drive bay
1 x 120mm low dB exhaust fan
2 x 92mm low dB intake fans
7
1 x headphone (HD & AC97)
1 x microphone (HD & AC97)
1 x multi format card reader
iMON IR controller (IR310)
9.8kg
black, silver
12.1” screen size (16:10)
1280 x 800 native resolution
1920 x 1080 max resolution
1 x SVGA input
12V dc input
9w power consumption
1 x USB 2.0 port
1 x USB 3.0 port

Power button
Power LED ring
TFT power ON/OFF button*
IR receiver windows
TFT stylus
Optical disk drive [bezel]
Optical disk drive eject button
12.1” touch screen TFT
I/O ports and card reader (p.17)
TFT contols (p.14)
TFT open/close button
One piece aluminum chassis
PSU bracket
Top panel fixing screw
Motherboard tray fixing screw
Removable motherboard tray
120mm low dB fan
Top panel
1
-
2
-
3
-
4
-
5 -
6 -
7 -
8 -
9 -
10 -
11 -
12 -
13 -
14 -
15 -
16 -
17 -
18 -
5
86 10
9
2
1 4 7
511
312
S21T overview
The following diagrams (below and overleaf) highlight the main features and controls of
the S21T htpc enclosure. Further information can be found throughout this user guide.
1413 15 1814 15 1517 15
*see page 16 for auto-power on feature
16
S21T overview

8 9 10
2 3 451 6 7
Hard drive (HD) stop-rail
Optical disk drive (ODD) cage
Motor assembly
92mm low dB fan
HD mounting bracket
ODD/HD support strut
One piece aluminum chassis
Moulded back panel frame
Removable motherboard tray
Extractor module mount
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8 -
9 -
10 -
6
S21T overview

Opening the case
To remove the lid of the
case, undo the 2 thumb
screws as indicated.
Carefully lift the lid from
the back but not too far -
DO NOT FORCE, and then
pull backwards. Reverse
procedure to replace lid.
12
Removing the motherboard tray.
Undo the 4 thumb screws as
indicated below. Pull the tray
backwards to remove. Reverse
this procedure when replacing
the tray, ensuring it is located
in the tray guides correctly.
7
Opening the case / removing the motherboard tray

VGA input
(connector
hub PCB)
8
Micro ATX standoff / VGA loop cable installation
VGA loop cable
This cable loops the VGA signal
from the graphics card to the
12.1” TFT via the VGA bracket.
It fits to the connectors as shown.
The VGA is then connected internally
(see page 13 for PCB / cable reference).
Micro ATX standoff installation
When installing a micro ATX motherboard, screw
the 2 standoffs provided in the locations illustrated
above. These are for micro ATX only and MUST
NOT be installed if using a full ATX motherboard.

Optical disc drive (ODD) installation
R
the 4 screws as illustrated below.
Install ODD into the cage using
the correct screws (supplied).
Re-position the cage, with drive,
and replace all screws to secure.
Adjust (forward/back) position as
necessary to ensure functionality
of ODD eject button.
emove the ODD cage by undoing
9
Optical disc drive installation

Optical disk drive (ODD) bezel installation.
The aluminum ODD bezel matches the finish of the case. The installation procedure requires that
the plastic drive bezel that comes fitted to your drive, be removed prior to installation. The drive
format icon should also be fitted to the bezel before installation. The metal sticker sheet supplied
has Blu-ray, HD-DVD or DVD icons, depending on the format being used.
Remove the existing plastic dirve bezel
from your ODD. This is usually done by
uncliping it and sliding it upwards. The
disc tray should be ejected when doing
this to gain access to the bezel.
Alignment
spacer
TOPTOP
Metal sticker fitting instructions.
Ensure the bezel is free from dirt of grease. Peel and fold back the yellow backing sheet, revealing
only the icon you intend to use. Carefully position the icon as central as possible, then apply even
pressure over the entire area. Peel off the plastic film (and unused icons) to reveal you handy work!
foam
tape
10
ODD bezel / metal sticker installation
With the tray closed, peel the back off the adhesive
foam strip on the back of the bezel. Using the
cardboard spacers, position the bezel as shown and
press firmly to ensure good adhesion. Eject the tray
to remove the spacers (a gentle tug may be required).

Hard drive installation.
T
as shown. You may need to loosen the
screws first with a screwdriver. Drives must
always be installed with the label facing
toward the front of case. Screw three rubber
mounting screws into the drive as shown
below (the screw arrangement is mirrored
for drives installed on the opposite side).
Use the chart on page 12 to determine
location, then lower the drive into place,
carefully guiding the bottom rubber mount
straight down the outer mount guide until
the upper mounts are sitting snugly at the
top of opposing guides. Once all drives
have been installed, secure the stop-rails.
o begin installation, remove the stop-rails
HD stop-rails.
When removing the stop-
rails, only the back screw
need be fully unscrewed-
loosening the front thumb
screw is all that ’s required
to remove the stop-rail
in the direction shown.
This screw
arrangement
is mirrored for
hard drives
installed on
the other side
of the case.
Hard drive installation

L
1 2 3 4 5 6 7 8 910
L
L
R
R
R
L
L
L
L
L
L
L
R
R
LEFT RIGHT
Ldrive on the left side only
drive on both sides
Rdrive on the right side only
Optimum position for maximised airflow and cooling
Hard drive configuration.
In order to maximise airfow
and cooling of the hard drives,
use the chart on the left to
determine the optimum install
configuration for the number
of drives to be installed. When
more that 6 drives are required,
careful motherboard and PCI
card selection is recommended,
as in some cases M/B connector
pin position or and oversized
graphics card may inhibit some
drive configurations. If this
occurs, the drive positions can
be reversed (left to right) or the
drive spacing decreased as
needed. Always try to maximise
the airflow wherever possible.
Number of hard drives to be installed
This diagram illustrates
a five HD configuration
using the chart above.
1 2 3 4 5 6 7 8 910
12
Hard drive configuration

PCB/cable reference diagram.
13
PCB/cable reference diagram
4
7
power
(MOLEX)
motor
8
(from hub)
1 2 3
6
5
TFT module
This is a general overview illustrating how the S21T PCBs interconnect. PCBs / Cables
dimmed in grey, come as part of an IR kit (sold separately). Please refer to your
motherboard manual for the location of the correct ports and header pins.
1 - TFT open / close button PCB
2 - S21T connector hub PCB
3 - TFT power on / off PCB
4 - IR module PCB (Ir310)
5 - IR in / out PCB
6 - Main power button PCB
7 - Motor control PCB
8 - VGA input (loop cable from VGA card)

TFT controls / menu operation
TFT controls / menu operation
12.1 inch TFT
(261 x 163mm)
aspect ratio
16 : 10
resolution
1280 x 800
supports
1920 x 1080
Begin by pressing the (menu/set) button to bring up the
on screen display (OSD). Use the and buttons to navigate
through the 10 menu categories. Press the button to select
a category, then (where appropriate) use to and to increase
or decrease the value as desired. Press the button again to
confirm the setting and repeat the process until you have made
all the required adjustments. To exit the OSD, simply locate the
EXIT category (10/10) and press (it will also exit automatically
after approximately 10 seconds of inactivity). The menu gudie
on the next page shows the route and the adjustment
sequence for each menu category (each assumes
you are not already in the menu, with the exception of Exit).
[in grey]
[in orange]
TFT power on / off *
Menu / set
Value up
Value down
*see page 16 for auto - power on feature
BRIGHTNESS - adjusts the picture brightness.
CONTRAST - adjusts the picture contrast.
PHASE - adjusts the noise of the image.
H POSITION - adjust the image horizontally.
CLOCK - adjusts video sampling clock.
V POSITION - adjust the image vertically.
LANGUAGE - language selection (default English).
AUTO - auto image adjust wizard.
RESET - resets to factory setting.
EXIT - exits the TFT menu.

Language (default is English).
follow the steps below to change language.
1
Contrast.
follow the steps below to adjust contrast.
Brightness.
follow the steps below to adjust brightness.
2
Phase.
follow the steps below to adjust phase.
5
V positions.
follow the steps below to adjust V position.
4
H positions.
follow the steps below to adjust H position.
Clock.
follow the steps below to adjust clock speed.
3
Exit.
follow the steps below to exit OSD.
Auto-adjust wizard.
follow the steps below to auto-adjust image.
Reset to factory settings.
follow the steps below to reset settings.
2
3
4
15
TFT menu guide

Hidden controls / features
Hidden controls / features
A few of the S21T’s controls and features have
been discreetly located in order to retain the clean
styling of the enclosure. These are as follows:
TFT power on/off - Quick access button
located near main power button with same
functionality as the power button on the TFT
TFT stylus location - Press to release
Auto-power on feature - Located on the
TFT open/close - Opens and closes the
lock, pull out to remove. Slide stylus into the
opening (tip first) and press to lock and stow
back of the TFT, between the and button.
Switched ON the TFT auto-powers up on boot,
switched OFF the TFT remains off on boot.
TFT panel, to provide access to the ODD drive,
multi-format card reader and front I/O ports.

4 7 8
6
53
2
1
1 - USB 3.0 port
2
- USB 2.0 port
3
- Compact flash reader
4
- Multi format reader
5
- Card reader power LED
6
- Activity indicator LED
7
- Audio socket
8
- Audio socket
Multi-format card reader & I/O ports
The S21T comes fitted with a multi-format
card reader as well as front audio, USB.
The [internal] USB hub feeds the
2 front USB ports as well as the IR control
and TFT touch panel, freeing up USB
connectors on the motherboard. The front
audio ports support both AC97 and
HD audio standards, while the card reader
supports all the card formats.
17
Multi-format card reader & I/O ports
1 Compact Flash Card TYPE I 20 Secure Digital Ultra II
Plus Card 39 Memory Stick (Magic Gate / High
2 Compact Flash Card TYPE II 21 Secure Digital Card 45X Speed
data transfer compatible)
3 Compact Flash Ultra Card TYPE I 45 X 22 Secure Digital PRO
Card 66X 40 Memory Stick
4 Compact Flash Ultra Card TYPE I 80 X 23 Secure Digital Card 80X (Magic Gate / High Speed data transfer
5 Compact Flash Ultra Card TYPE I 120 X 24 Secure Digital Card 133X compatible with memory select function)
6 Compact Flash Ultra II Card TYPE I 25 Secure Digital Card 150X 41 Memory Stick Pro
7 Compact Flash Extreme Card 26 Mini Secure Digital Card 42 Magic Gate Memory Stick
8 Compact Flash Extreme III Card 27 Mini Secure Digital Ultra II Card 43 Magic Gate Memory Stick
9 Compact Flash ELITE PRO Card 28 Mini Secure Digital Card 80X 44 Memory Stick Pro HS
10 Compact Flash Ultimate Card 100X 29 Mini Secure Digital PRO Card 45 Memory Stick Pro Ultra II
11 Compact Flash Ultra-X Card 140X 30 Micro Secure Digital Card 46 Memory Stick Pro Extreme
12 IBM Micro Drive Card 31 Micro Secure Digital Ultra II Card 47 Memory Stick Pro Extreme III
13 Sony Micro Drive Card 48 Memory Stick Pro
32 Multi Media Card 49 Memory Stick Pro Duo
14 Smart Media Card 33 Multi Media PRO Card 50 Memory Stick Pro Duo HS
34 Multi Media Plus Card 51 Memory Stick Pro Duo
15 XD-Picture Card 35 Reduced Sized Multi Media Card 52 Memory Stick Duo (Magic Gate / High
36 Reduced Sized Multi Media Mobile Card Speed data transfer compatible)
16 Secure Digital Card 53 Memory Stick Pro Duo
17 Secure Digital Ultra II Card 37 Memory Stick 54 Magic Gate Memory Stick Duo
18 Secure Digital Extreme Card 38 Memory Stick 55 Magic Gate Memory Stick Duo
19 Secure Digital Extreme III Card (With memory select function) 56 Memory Stick ROM
NOTE: Card adapter required for some formats

Touch panel software installation.
In order to use the touch panel, you must first install the
TouchKit software from our website. To start the software
installation, double click on the setup.exe file located in the
TouchKit folder.
18
1 After opening the setup.exe
file, the install will begin with
the above prompt. Click ‘Next’
to continue.
2 Ensure that ‘install PS/2
interface driver ’ is not
selected and click ‘Next ’.
3 Sel ec t ‘None’ and cl ick ‘Ne xt ’
Af ter co mpl et ing the ins tal l, the
Touc hKi t so ftwar e will pe rfor m
a 4 poi nt ca libr at ion.
4 The touchscreen controller
should already be connected
if you have correctly
connected all cables inside
your chassis. Click ‘OK’.
5 If you intend to use spaning
mode with multiple monitors,
please select ‘Support Multi-
Monitor Systems’. Click ‘Next’
to continue.
6 Change the TouchKit
softwa re install folder if
required and click ‘Ne xt ’
to continue.
x
Touch panel software installation

19
7 Change the Program
Folder name if required and
click ‘Ne xt ’ to continue.
8 Click ‘ Yes’ to per for m a
4 poi nt cal ibr at ion. Th is is
requ ired for pr oper touch
scr een oper at ion.
9 The softwa re wi ll now scan
and install the touch screen
device. The TouchKit calibration
procedure wi ll follow.
10 To per for m the ca libr at ion, pr es s and hol d dow n
the X that bl ink s in the co rner of the sc ree n, unt il it
di sa ppe ar s. Repe at thi s pr oc edu re with ea ch of the
4 X’ s that appe ar. On co mpl et ion of thi s, the touc h
sc ree n will be ca libr at ed and rea dy for use .
x
Press the blinking X symbol until it stops blinking
x
Touch panel software installation

Global HQ
Website
#209 Baesan B/D
763-2 Hengsin-Dong
Dukyang-Gu
Goyang City
Gyounggi-Do
412-220 South Korea
www.origen .comae
Origen