Orlaco 0506811 User manual

Camera PTZ HD-E Alu/Sst
Installation Manual
Manual No. IM0973550, A 08
Article no. 0506811
0506821
Including installation Junction boxes:
Junction box HD-E camera 24V/DC in
Article. no. 0504880
Junction box HD-E camera 230V/AC in
Article. no. 0504870
Junction box HD-E camera PoE
Article. no. 0504860
8/2015
English
Art. no. 0506811
Art. no. 0506821

2 IM0973550 A 08
Installation Manual
Camera PTZ HD-E Alu; Art. no. 0506811
Camera PTZ HD-E Sst; Art. no. 0506821
Including installation Junction boxes:
Junction box HD-E camera 24V/DC in
Article. no. 0504880
Junction box HD-E camera 230V/AC in
Article. no. 0504870
Junction box HD-E camera PoE
Article. no. 0504860
Safety
In order to guarantee safe operation, these safety instruc-
tions must be read before you start using this equipment.
• Do not open the enclosure. The camera is pressurised.
This can cause damage, short-circuiting or electrical shocks.
• Do not expose the equipment to extreme temperatures. This can cause
deformation of the enclosure or damage to internal components.
• Repairs or adjustments to the equipment may only be undertaken by
Orlaco.
• The equipment must be assembled as shown in this manual.
• If there have been alterations or changes to this equipment that have
not been specifically approved by Orlaco, use of this equipment is not
permitted.
Before you start using this equipment, please read this manual carefully
and follow all instructions. This installation manual describes the func-
tions of the equipment, outlines the connection options and explains how
to put the equipment into operation. We recommend that you keep this
manual in a safe place for reference purposes.
If you have any questions or issues concerning the operation of this
equipment, consult the relevant section in the manual or contact the
Orlaco Products BV Service department.
The camera and monitor systems from Orlaco comply with the latest CE,
ADR, EMC and mirror-directive regulations. All products are manufac-
tured in accordance with the ISO 9001 quality management, IATF 16949
quality automotive and ISO 14001 environmental management.
Contents Page
1. Introduction 3
2. Configuration 3
3. Mounting 3
3.1. Mounting safety cables 3
4. Operation 3
4.1. Overpressure in the enclosure 3
4.2. Switching on and off 3
5. Electrical installation 4
5.1. Camera PTZ HD-E 4
5.2. System overview standard configuration 4
5.3. Cable connections Junction box HD-E camera 24V/DC 5
5.4. Cable connections Junction box HD-E camera 230V/AC 6
5.5. Cable connections Junction Box Cable extension 6
5.6. Cable connections Junction box HD-E camera PoE 6
6. Adjusting the IP address 7
7. Troubleshooting 8
8. Maintenance and cleaning 8
9. Technical specifications 9
9.1. Cameras 9
9.2. Junction boxes 9
10. Dimensions 10
11. Disposal 10
12. General terms and conditions 10
13. Release notes 10
Available documentation
DS0961320-0506811 Camera PTZ HD-E Alu
DS0961321-0506821 Camera PTZ HD-E Sst
DS0963150-0504860 Junction box HD-E camera PoE
DS0963151-0504870 Junction box HD-E camera 230V/AC in
DS0963152-0504880 Junction box HD-E camera 24V/DC in
Art. no. 0506811
Art. no. 0506821
Art. no. 0504870
Art. no. 0504880
Art. no. 0504860

IM0973550 A 08 3
Installation Manual
1. Introduction
Pan Tilt unit including digital full HD zoom camera with ethernet interface.
The Pan & Tilt unit functions via two industrial stepping motors. These
stepping motors are controlled by the integrated micro-controller. The
camera has a web GUI interface (HTTP or HTTPS). Control and view of
the camera is done over TCP/IP in a computer network.
Weather-, shock-, vibration-, corrosionproof.
2. Configuration
The space required for panning and tilting is:
Panning: 315mm.
Tilting: 370mm.
See also figure 6, page 7. When positioning the PTZ unit, account must
be taken of the space required for panning and tilting. There must be no
obstacles in this space.
3. Mounting
The PTZ unit has a base. Mount the PTZ unit upright.
The PTZ unit may not be mounted hanging or at a right
angle! This would put too much pressure on the base
and mechanical components.
To affix the PTZ unit, use a pole bracket or a wall bracket. Or mount the
PTZ unit directly to a metal surface.
Note the starting position of the camera; this is indicated as the zero posi-
tion in figure 1.
Use a Allen key to secure the PTZ unit with three M8 x 20mm Stainless
steel bolts(included). The base of the PTZ unit has three recessed holes.
Mount the bolts (Hexagon socket countersunk head screws) from the
upper side of the base. For details of the size of the attachment points,
see figures 5 and 6.
3.1. Mounting safety cables
Mount the fall protection to a fixed point. Use three cable clamps for
attachment. These cable clamps must to be installed correctly; see figure
2. Mount the safety cable from the camera to a fixed mounting point on
the same surface and height as the Base plate, see figure 4.
4. Operation
4.1 Overpressure in the enclosure
The enclosure of the Camera and PTZ unit has a 1,4-bar overpressure.
4.2 Switching on and off
First of all, position the PTZ unit in the zero position as indicated in
figure 1.
The PTZ unit configuration is switched on by connecting the connector
cables to the power supply. It is switched off by disconnecting the con-
necting cable from the power supply. See figure 7.
Ensure that the PTZ unit and other components of
the installation are closed so that it is not possible to
come into contact with moving parts.
Ensure that all parts are firmly fixed, stable and
secure.
Check that the power and connector cables are suit-
able for the system power supply.
Do not get too close to the PTZ unit when the system
is switched on. There is a risk of injury.
CORRECT
INCORRECT
INCORRECT
U-Bolt of all clips on
dead end of rope
Staggered clips
U-Bolt of all clips on
live end of rope
Figure 1
Figure 3
Horizontal zero position
view direction
Cover plate
Cable Base
art. no 1221300
length 5,5m
Open
wired
Cable
fall protection
Base
Base plate
Socket head wrench
Socket head wrench
M5 Socket head screw
Fall protection
Fall protection
3 Bolts M8 x 20mm
Base
Base plate
Cover plate
Cover plate
Figure 2
40

4 IM0973550 A 08
Installation Manual
5. Electrical installation
5.1. Camera PTZ HD-E
Art. no. 0506811 Camera PTZ HD-E Alu
Art. no. 0506821 Camera PTZ-HD-E Sst
Cable Ethernet AFZ/PTZ, Art. No. 1221340
1. Brown N.C.
2. Blue N.C.
3. Black/blue N.C.
4. Red/blue N.C.
5. Blue Serial - 1*
6. White Serial - 2*
7. Grey Serial 0V
8. Red/white P&T Power 24V in
9. Black/white P&T Power 0V in
10. Red Camera power 24V in
11. Black Camera power 0V in
12. Orange/white Ethernet TX+
13. Orange Ethernet TX-
14. Green/white Ethernet RX+
15. Green Ethernet RX-
The PTZ unit must be connected by trained electri-
cians. Under no circumstances should you make
connections that are not described in this manual.
5.2 System overview standard configuration
The following products are required for basic operation of the PTZ unit,
see figure 7:
PTZ unit Art. No. 0506811/0506821.
Junction box Ethernet, Art. No. 0504870/80. For cable layout see figure 8.
Ethernet switch and PC (for smartview). Third party.
R = 50,0
M8 x 1,25 (3x) horizontal zero position
Cable
120°
90°
30°
120°
Base
back side
Base plate
Top side
150
120° (3x)
M8 (3x)
R = 50,0
∅
12 (4x)
Figure 6
R = 50,0
M8 x 1,25 (3x) horizontal zero position
Cable
120°
90°
30°
120°
Base
back side
Base plate
Top side
150
120° (3x)
M8 (3x)
R = 50,0
∅12 (4x)
Figure 5
Camera cable
Top view
Base Plate
∅2 safety cable
from the camera
length 360-370
between camera
and wire rope
clamp
60 ±10
wire rope clamps (3x)
Mount the safety cable from
the camera on a fixed
mounting point on the same
surface and height as
the Base plate
Base plate
fixed mounting point
Base
Figure 4
Camera cable
Top view
Base Plate
∅2 safety cable
from the camera
length 360-370
between camera
and wire rope
clamp
60 ±10
wire rope clamps (3x)
Mount the safety cable from
the camera on a fixed
mounting point on the same
surface and height as
the Base plate
Base plate
fixed mounting point
Base

IM0973550 A 08 5
Installation Manual
Camera PTZ HD-E Alu
Art. No. 0506811
Camera PTZ HD-E Sst
Art. No. 0506821
Power
Power
Cable ethernet AFZ/PTZ
Art. No. 1221340 S/FTP
Junction Box
Art. No. 0504870/80
Ethernet switch
3,8m
Power (230V/AC or 24V/DC)
S/FTP
Camera PTZ HD-E
Default IP: 192.168.40.90
Embedded PC requirements:
- Intel Quad core i7, 2.0GHz
- 2GB memory
- 20GB HDD
- Windows 7/10
Recommended embedded PC:
- Orlaco 0000010
Max cable length between camera and switch: 60m Max 100m
point to point
Figure 7
5.3. Cable connections Junction box HD-E camera 24V/DC
Art. No. 0504880.
See figure 8A. For specifications see chapter 9.
Cable Ethernet AFZ/PTZ, Art. No. 1221340
1 = Blue = Serial 1
2 = White = Serial 2
3 = Grey = Serial 0V
4 = Red/White = 24VDC
5 = Black/White = GND
6 = Red = 24VDC
7 = Black = GND
8 = White/Orange = TX+
9 = Orange = TX-
10 = White/Green = RX+
11 = Green = RX-
12 = N.C.
Multicable 7wire AWG20, Art. No. 1220900
6 = Red = 12/24VDC
7 = Black = GND
Cable Ethernet S/FTP
8 = White/Orange = TX+
9 = Orange = TX-
10 = White/Green = RX+
11 = Green = RX-
Screw terminal connections
Junction Box Cable extension; Art. No. 0504880
Art. no. 1221340 Art. no. 1221340
Cut off:
Brown
Blue
Black/Blue
Cut off:
Brown
Blue
Black/Blue
Red/Blue
Blue
White
Shield
Gland Plug
Cable shielding connection clamp
Screw terminal connections
Junction Box HD-E 24V/DC; Art. No. 0504880
Art. no. 1221340
S/FTP
Cut off:
Brown
Blue
Black/Blue
Red/Blue
Power cable
Cable shielding connection clamp
Screw terminal connections
Junction Box HD-E 230V/AC; Art. No. 0504870
Art. no. 1221340
S/FTP
Cut off:
Brown
Blue
Black/Blue
Red/Blue
Mains power
cable
Cable shielding connection clamp
Screw terminal connections
Junction Box HD-E PoE; Art. No. 0504860
Art. no. 1221340
S/FTP
Cut off:
Brown
Blue
Black/Blue
Red/Blue Cable shielding connection clamp
POE IN DATA OUT
DC OUT
Figure 8A

6 IM0973550 A 08
Installation Manual
5.4. Cable connections Junction box HD-E camera 230V/AC
Art. No. 0504870.
See figure 8B. For specifications see chapter 9.
Cable Ethernet AFZ/PTZ, Art. No. 1221340
1 = Blue = Serial 1
2 = White = Serial 2
3 = Grey = Serial 0V
4 = Red/White = 24VDC
5 = Black/White = GND
6 = Red = 24VDC
7 = Black = GND
8 = White/Orange = TX+
9 = Orange = TX-
10 = White/Green = RX+
11 = Green = RX-
12 = N.C.
Cable Ethernet S/FTP
8 = White/Orange = TX+
9 = Orange = TX-
10 = White/Green = RX+
11 = Green = RX-
5.5. Cable connections Junction Box Cable extension
Art. No. 0504880.
See figure 8C. For specifications see chapter 9.
5.6. Cable connections Junction box HD-E camera PoE
Art. No. 0504860.
See figure 8D. For specifications see chapter 9.
Cable Ethernet AFZ/PTZ, Art. No. 1221340
1 = Blue = Serial 1
2 = White = Serial 2
3 = Grey = Serial 0V
4 = Red/White = 24VDC
5 = Black/White = GND
6 = Red = 24VDC
7 = Black = GND
8 = White/Orange = TX+
9 = Orange = TX-
10 = White/Green = RX+
11 = Green = RX-
12 = N.C.
Cable Ethernet S/FTP
Not applicable
Screw terminal connections
Junction Box Cable extension; Art. No. 0504880
Art. no. 1221340 Art. no. 1221340
Cut off:
Brown
Blue
Black/Blue
Cut off:
Brown
Blue
Black/Blue
Red/Blue
Blue
White
Shield
Gland Plug
Cable shielding connection clamp
Screw terminal connections
Junction Box HD-E 24V/DC; Art. No. 0504880
Art. no. 1221340
S/FTP
Cut off:
Brown
Blue
Black/Blue
Red/Blue
Power cable
Cable shielding connection clamp
Screw terminal connections
Junction Box HD-E 230V/AC; Art. No. 0504870
Art. no. 1221340
S/FTP
Cut off:
Brown
Blue
Black/Blue
Red/Blue
Mains power
cable
Cable shielding connection clamp
Screw terminal connections
Junction Box HD-E PoE; Art. No. 0504860
Art. no. 1221340
S/FTP
Cut off:
Brown
Blue
Black/Blue
Red/Blue Cable shielding connection clamp
POE IN DATA OUT
DC OUT
Screw terminal connections
Junction Box Cable extension; Art. No. 0504880
Art. no. 1221340 Art. no. 1221340
Cut off:
Brown
Blue
Black/Blue
Cut off:
Brown
Blue
Black/Blue
Red/Blue
Blue
White
Shield
Gland Plug
Cable shielding connection clamp
Screw terminal connections
Junction Box HD-E 24V/DC; Art. No. 0504880
Art. no. 1221340
S/FTP
Cut off:
Brown
Blue
Black/Blue
Red/Blue
Power cable
Cable shielding connection clamp
Screw terminal connections
Junction Box HD-E 230V/AC; Art. No. 0504870
Art. no. 1221340
S/FTP
Cut off:
Brown
Blue
Black/Blue
Red/Blue
Mains power
cable
Cable shielding connection clamp
Screw terminal connections
Junction Box HD-E PoE; Art. No. 0504860
Art. no. 1221340
S/FTP
Cut off:
Brown
Blue
Black/Blue
Red/Blue Cable shielding connection clamp
POE IN DATA OUT
DC OUT
Figure 8B
Figure 8C
Screw terminal connections
Junction Box Cable extension; Art. No. 0504880
Art. no. 1221340 Art. no. 1221340
Cut off:
Brown
Blue
Black/Blue
Cut off:
Brown
Blue
Black/Blue
Red/Blue
Blue
White
Shield
Gland Plug
Cable shielding connection clamp
Screw terminal connections
Junction Box HD-E 24V/DC; Art. No. 0504880
Art. no. 1221340
S/FTP
Cut off:
Brown
Blue
Black/Blue
Red/Blue
Power cable
Cable shielding connection clamp
Screw terminal connections
Junction Box HD-E 230V/AC; Art. No. 0504870
Art. no. 1221340
S/FTP
Cut off:
Brown
Blue
Black/Blue
Red/Blue
Mains power
cable
Cable shielding connection clamp
Screw terminal connections
Junction Box HD-E PoE; Art. No. 0504860
Art. no. 1221340
S/FTP
Cut off:
Brown
Blue
Black/Blue
Red/Blue Cable shielding connection clamp
POE IN DATA OUT
DC OUT
Figure 8D

IM0973550 A 08 7
Installation Manual
Figure 9
Figure 10
Figure 11 Figure 12
Figure 15
Figure 14
Figure 13
6. Adjusting the IP address
The camera is programmed with a fixed IP address at 192.168.40.90.
Adjusting the IP address according to the IP plan of the complete camera
system is done with the IONODES configuration tool, see figure 9.
Run IonConfigtool.exe and wait for the camera to appear.
Make sure that the IP address of your PC is in the 192.168.40.xx range.
When this is the case, the green check box will be present.
Right mouse click, Identify Device.
Right mouse click, assign IP address(es), see figure 10.
Fill in the desired IP address, click Start, wait for assigned successfully,
see figures 11 and 12.
Click close.
Right mouse click on the camera, configuration web page (or just type
the IP address of the camera in an IE web browser). The login screen will
appear, see figure 13.
Username: admin
Password: admin
Go to configuration, network, multicast, make the following setting:
Multicast start IP: 237.0.0.91, see figure 14.
Click Save.
These steps have to be repeated for every camera in the system
individually to avoid IP conflicts. When all camera’s are configured
according to the IP plan, they can be power simultaneously.
Example of configuration tool of a 4 camera HD-E system, see figure 15.
Note: the configuration web page can only be used
for adjusting the camera IP address and Multicast
start IP address as described in this chapter.
It is not allowed to make any additional changes in the camera settings.
Any other changes in the settings will influence the performance of the
camera system or even result in a malfunction.

8 IM0973550 A 08
7. Troubleshooting
8. Maintenance and cleaning.
Use a soft cloth to remove dirt etc. from the lens.
Do not clean this product with aggressive chemicals
or abrasive cleaning agents.
The filling valve may ONLY be used by the manufacturer.
Do not remove the blue seal. See figure 15. The warranty expires when
the blue seal is broken!
The warranty expires when the user does not act ac-
cording the instructions and warnings in this manual.
Installation Manual
Figure 15
Filling valve
Filling valve
Problem
1. Display does not work.
2. Display has no picture.
3. Camera does not work.
5. PTZ does not work.
Possible cause
System is not switched on.
System is not connected or the supplied voltage
of the vehicle to which the system is connected
is too low (flashing LED on camera).
Fuse of the vehicle’s supply voltage is defective.
Other cause.
Display is not or incorrectly connected to the
control box.
Camera is not functioning.
Other cause.
Camera is not or incorrectly connected.
The camera is defective.
Other cause.
PTZ not or incorrectly connected to the camera.
Other cause.
Solution
Connect the Power cable to the right power
supply.
Connect the system and measure the vehicle’s
supplied voltage when the system is switched
on.
Replace the fuse.
Contact your Orlaco dealer.
Check the connection of the Display
See problem 3.
Contact your Orlaco dealer.
Check the connection of the PTZ to the opera-
ting panel and make sure the red LED on the
camera is lit.
Contact your Orlaco dealer.
Contact your Orlaco dealer.
Check the connection of the Display to the
camera.
Contact your Orlaco dealer.

IM0973550 A 08 9
Installation Manual
9. Technical specications
9.1. Cameras:
Art. no. 0506811 Camera PTZ HD-E ALU.
Art. no. 0506821 Camera PTZ HD-E SST.
Sensor
Imager: 1/2.8 Type Exmor CMOS Sensor.
Picture elements: 2,38 Megapixels.
Lens: 30x Zoom F=4.3mm (WIDE) to 129mm (TELE), F1.6 to F4.7.
Angle of view (H): ±63.7° (wide end), ±2.3° (tele end).
Min. working distance: 10 mm (WIDE end), 1200 mm (TELE end).
Min. illumination: (50%, High Sensitivity Mode ON).
ICR-Off mode: 0.01lx, 1/30s. ICR-ON mode: 0.0015lx, 1/30s.
S/N ratio: >50 dB
Video Compression
Standards: H.264 High, Main and Baseline profiles, Motion JPEG.
Data rate: 64 kbps to 10 Mbps per channel (requires less than 1 Mbps at
4CIF/30fps)
Resolutions: Up to HD 720p at 60 fps / 1080p at 30 fps (16:9).
Latency: < 200ms. (Latency measured at 720p at 60 fps).
Start up time: < 100 sec.
Protocols
Networking: IPv4/v6, UDP, TCP, IGMP, ICMP, ARP, DHCP, DNS.
Streaming: RTP, HTTP.
Management: RTSP, HTTP, HTTPS, Bonjour, NTP, Telnet, FTP, SNMP.
PTZ integration: Pelco D.
Electrical
Input voltage range: 18...30VDC.
Power consumption: Heating on: 23W & Heating off: 18W.
Communication: Ethernet.
Cable: Art. no. 1221340; Cable Ethernet AFZ/PTZ, 5,0m, open wired.
PTZ
Pan angle: Total 360°, 180° left, 180° right.
Tilt angle: Total 180°, 90° up, 90° down.
Backlash PTZ:1°.
Fixed camera pos: 6 preset camera positions, preset tolerance: <1°.
Pan & Tilt speed: 12,5°/sec.
Mechanical
Construction Camera Alu: Stainless steel 316 mounting parts, anodised
aluminium housing and sun cover, suitable for mobile applications with
shocks and vibrations.
Construction Camera Sst: Housing, mounting parts and sun cover; stain-
less steel 316, suitable for mobile applications with shocks and vibra-
tions.
Ingress protection: Corrosion proof housing according to MIL-A-8625E
(Acetic Acid Salt Spray Test), IP68 according to IEC 60529, Dust tight
and protected against the effects of immersion in water up to 10m for 30
minutes and IP69K according to DIN 40050-9, camera can withstand a
high pressure cleaning with water: 14-16L/min 80°C and 100 Bars flow.
Dry-nitrogen filled, 1,4 Bar overpressure.
Protection: IP 69K according IEC 60529, 1,4 Bar overpressure filled with
dry nitrogen.
Operating temperature: -40°C to +60°C.
Weight Camera Alu: 6,8 kg.
Weight Camera Sst: 15 kg.
Features
Full HD image sensor 1080p30
Video streaming over TCP/IP
9.2. Junction boxes
Art. no 0504870 Junction box HD-E camera 230V/AC.
General
Junction box for applying mains power to Orlaco HD Ethernet Cameras.
Housing: Polycarbonat.
Protection: IP66.
Terminal blocks: Included, 12p, 200 V / 13,5A.
Temperature range: -40°C to +70°C.
Shock resistance: IK 08 PC, Sinusoidal Vibration test compliant.
Cable glands: 3 cable glands for diameter range 3 to 9mm. IP68.
Weight:0,7kg. With power cable 230V. Length: 2m.
Input voltage range: 88-273 V/AC in.
Art. no 0504880 Junction box HD-E camera 24V/DC.
General
Junction box for applying 24V/DC power to Orlaco HD Ethernet Cameras.
This junction box can also be used as camera cable extension box.
Housing: Polycarbonat.
Protection: IP66.
Terminal blocks: Included, 12p, 200 V / 13,5A.
Temperature range: -40°C to +70°C.
Shock resistance: IK 08 PC, Sinusoidal Vibration test compliant.
Cable glands: 3 cable glands for diameter range 3 to 9mm. IP68.
Weight: 0,4kg.
Art. no 0504860 Junction box HD-E camera PoE
General
Junction box for applying Power over Ethernet (PoE) to Orlaco HD Ether-
net Cameras.
Housing: Polycarbonat.
Protection: IP66.
Terminal blocks: Included, 12p, 200 V / 13,5A.
Temperature range: -40°C to +70°C.
Shock resistance: IK 08 PC, Sinusoidal Vibration test compliant.
Cable glands: 2 cable glands for diameter range 3 to 9mm. IP68.
Weight: 0,4kg.
Certication
Approvals: In compliance with all relevant EMC directives. Certificates
available upon request.

10 IM0973550 A 08
Installation Manual
10. Dimensions
For dimensions see figure 16.
11. Disposal
Disassembly, removal and disposal. Local regulations for dealing with
waste must be followed when disposing of disassembled components or
entire units.
12. General terms and conditions
Orlaco Products BV is not liable for damage resulting from inadequate
servicing, incorrect usage or alterations made to the equipment without
informing the manufacturer in writing.
This installation manual has been made available by Orlaco Products
BV. All rights reserved. No part of this manual may be reproduced and/
or made public in printed form, in photocopy form or on microfilm, or in
any other way, without the prior written permission of Orlaco. This also
applies to the associated drawings and figures.
Orlaco reserves the right to make changes to components at any time
without informing customers beforehand or directly. All dimensions given
are for commercial purposes.
For information regarding repairs that is not covered in this manual,
please contact the Orlaco Products BV service department.
This manual has been prepared with all due care and attention. However,
Orlaco Products BV cannot be held responsible for any errors in this
manual or any consequences thereof.
13. Release Notes
R1-0. First edition 8/2015.
R1-1. Multiple electrical changes 12/2015.
R1-2. Art. No. fig. 7 changed, Chapter 6 deleted, 01/2016
A 01. Specifications and Junction box changed,11/2016.
A 02. Junction box HD-E camera PoE added, 01/2017.
A 03. Text added to chapter 6, 04/2017.
A 04. Input voltage range added, chapter 9.2. , 09/2017.
A 05. Panning degrees changed in specs, 04/2018.
A 06. Latency specifications changed, chapter 9, 12/2019.
A 07. Specifications; Min. illumination changed, 01/2020.
A 08. Text features changed changed, 09/2020.
Maximum deflection turning 315
Maximum height 392
Tilt
Pan
141
261,5 Tilt 90˚ up
Tilt 90˚ down
307
299,4
112
P
a
n
3
6
0
˚
Base plate
Base
∅180
150
Base plate
Base
Base plate
Units in mm
Figure 16