OTTFF B018FXNV0O User manual

Instruction manual
LED Disco Light
RGB
PC Cover Rotation Prohibit!!!
Attention

English 1
Explanation of Symbols
Safety instructions:
Please read them carefully and comply with them in or-
der to prevent personal injury and damage to property.
Supplementary information
Contents
Intended Use ______________________________ 2
Safety Instructions__________________________3
Items Supplied_____________________________4
Inserting / Changing Batteries _________________5
Putting Into Operation _______________________6
Technical Data_____________________________6
Disposal__________________________________7
PC Cover Rotation Prohibit!!!
Attention

2
Dear Customer,
We are delighted that you have chosen this LED party light.
Before using the article for the first time, please read the
instructions through carefully and keep them for future refer-
ence. If the article is given to someone else, it should always
be accompanied by these instructions.
The manufacturer and importer do not accept any liability
if the information in these instructions is not complied with.
Intended Use
❐This article is suitable for decorating and lighting dry indoor
areas.
❐The article is designed for personal use only and is not in-
tended for commercial applications. Use the article only as
described in the instructions. Any other use is deemed to be
improper. Keep the instructions in a safe place.
❐The following are excluded from the warranty: all defects
caused by improper handling, damage or unauthorised
attempts at repair. This also applies to normal wear and tear.
English

3
Safety Instructions
Dangers of Injury
❐Batteries can be deadly if swallowed. Therefore keep bat-
teries and the article out of the reach of children and an-
imals. If a battery is swallowed, seek medical assistance
immediately.
❐Do not look directly into the light source! It could damage
your eyes.
❐Keep children and animals away from the packaging mate-
rial. There is a danger of suffocation!
❐This is not a toy! Keep children and animals away from the
article. Children must be supervised in order to ensure that
they do not play with the article.
The Proper Handling of Batteries
❐Before inserting the battery, check whether the contacts in
the battery compartment and on the battery are clean, and
clean them if necessary.
❐Use only the battery type specified in the technical data (see
the "Technical Data" section).
❐When replacing batteries, ensure the correct polarity (+/–).
❐Take the battery out of the battery compartment when it
is discharged or if the article is not going to be used for a
prolonged period. This will prevent any damage that might
occur if a battery leaks.
❐If the battery has leaked, do not allow battery acid to come
into contact with your skin, eyes, or mucous membranes. If
you touch battery acid, rinse the affected sites with abun-
dant fresh water immediately and contact a doctor as soon
as possible.
English

4
❐Remove a leaking battery from the battery compartment
immediately. Clean the contacts before you insert a new
battery.
❐The battery must not be charged or reactivated in any way,
it must not be disassembled, thrown into a fire, immersed in
liquids or short-circuited.
The Proper Handling of the Article
❐The light may not be used for the direct irradiation of people,
animals or plants.
❐Do not take the light and the remote control apart. Have any
repairs done only by a specialist workshop or the customer
service department.
❐Do not place any covers, e.g. cloths or similar items, over
the light. Contact with these sources could lead to a fire.
❐Do not drop the article or subject it to severe impact.
❐If you do not intend to use the article for a prolonged period
of time, switch off the article and store it in a dry place.
❐Do not use the article if it has visible signs of damage.
❐Do not expose the light to extreme temperatures, strong
temperature fluctuations or moisture.
❐Do not use any corrosive or abrasive cleaning agents to
clean the article! They could damage the surface.
Items Supplied
•1 x LED light
• 1 x Instruction manual
English
•1 x remote control incl. battery (type CR2025)

5
Overview of Remote Control
1 On/Off Switch
2 Music Sensor Switch
3 Brightness Setting
4 Speed Setting
5
Control pad for colour se-
lection
6
Color Change Mode
Inserting / Changing Batteries
The battery in the remote control is not inserted.So you
Have to insert a CR2025 type bettery before use.
1. Push the catch on the battery compartment to the right us-
ing your finger nail and pull out the battery compartment.
2. Remove the used battery and dispose of it in an environ-
mentally friendly way.
3. Insert a 3 V battery of the CR2025 type. Ensure the correct
polarity (+/-) when inserting the battery.
4. Place the battery compartment back into the remote control.
It must engage audibly.
English

6
Putting Into Operation
1. Unpack the items supplied and remove all protective films
and stickers. Check all parts for possible transport damage.
If you find any transport damage, contact the customer ser-
vice department immediately.
2. Screw the LED light into a suitable lamp fitting (E27/B22).
3. Switch on the LED light by switching on the light switch on
the lamp and pressing the On/Off) button (1) on the remote
control. The light begins to rotate after it has been switched
on.
4. Use the control pad for colour selection (6) to select a colour
or a colour combination.
5. When you press the colour change button
(5), the 5 basic colours light up alternately. Press any colour
selection button to switch off colour change mode.
6. Use the speed setting buttons (4) to set the speed of rota-
tion of the LED light.
7. Use the brightness setting buttons to set the brightness of
the LED light.
8. When you press the Music Sensor button
(2), the LED light flashes with the rhythm of the music which
is currently playing. Press any button to switch off the music
sensor.
9. To switch off the LED light, press the On/Off button (1).
Technical Data
Control Mode: Remote Controller
LED Source: RGB Full Color
Fitting: E27/B22
Voltage supply:
Light: 100-240V~ 50/60Hz, max. 3 watt
Remote control: 3 V DC (1 x 3 V button cell, CR2025 type)
English
Optional

7
Disposal
The packaging material is recyclable. Please dispose
of it in an environmentally friendly manner and take it
to a recycling centre.
Dispose of the article in an environmentally friendly
manner. The article should not be disposed of in the
normal domestic waste. Please dispose of it at a recy-
cling centre for used electrical and electronic devices.
You can obtain more information from your local au-
thorities.
Non-rechargeable and rechargeable batteries should
be removed before the article is disposed of and should
be disposed of separately from the article. To protect
the environment, non-rechargeable and rechargeable
batteries may not be disposed of with normal house-
hold waste, but must be taken to suitable collection
points. Also note the relevant statutory regulations
governing the disposal of batteries.
All rights reserved.
English
PC Cover Rotation Prohibit!!!
Attention

FCC WARNING
This device complies with part 15of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found tocomply with the limits for aClass B
digital device, pursuant to Part 15 oftheFCC Rules. These limits are designed to provide
reasonable protection against harmful interference ina residential installation. This equipment
generates, uses and can radiate radio frequency energy and, ifnot installed and used in
accordance with the instructions, may cause harmful interference toradio communications.
However, there is no guarantee that interference will not occur ina particular installation.
If this equipment does cause harmful interference toradio ortelevision reception,
which can be determined by turning the equipment off and on, the user isencouraged to try to
correct the interference byone ormore of the following measures:
-- Reorient orrelocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on acircuit different
from that towhich the receiver is connected.
-- Consult the dealer oran experienced radio/TV technician for help.