Outdoor Tech CHIPS ULTRA User manual

CHIPS ULTRA &
CHIPS ULTRA 2.0
REPLACEMENT
CASE
So you need another case for your Outdoor
Tech®Chips® Ultra and/or Chips® Ultra 2.0
true wireless helmet audio. Well here you go.
Your experience of the universe will soon
be enhanced. This manual exists to help
make sure that you use it correctly, so you’re
definitely going to want to relax for a hot
second and look through this.
Kisses,
WHAT’S INSIDE
• Charging case
• USB-C charging cable
• Instruction manual
• One ODT sticker
NEW Faster Charging - USB to USB-C cable
CHARGING CASE
CHARGING-THE CASE
Charge up the case so you always have power for your
Chips®Ultra or Chips®Ultra 2.0 on the go.
Fast charging with the new USB-C cable. Once the
charging case is plugged in the indicator light on the
front will turn RED- (CHARGING). It will turn GREEN once
the case is completely charged.
Case total charging time: 1.5 hours to fully charge the
case.
Case Battery: 3.7V 2000 mAh

K, Later gator.
outdoortech.com
DON’T BE SO ANTISOCIAL
Facebook.com/outdoortechnology
Twitter & Instagram: @outdoortech
Questions, comments, complaints, secret desires,
or just to say what’s up: email [email protected]
K bye.
Caution: The user is cautioned that changes or modifications not
expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
This device complies with Part 15 of the FCC Rules and Industry
Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
FCC& IC Radiation Exposure Statement:
This equipment complies with FCC and Canada radiation exposure
limits set forth for an uncontrolled environment.
This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
Déclaration d’IC sur l’exposition aux radiations:
Cet équipement est conforme aux limites d’exposition aux radiations
définies par le Canada pour des environnements non contrôlés.
Cet émetteur ne doit pas être installé au même endroit ni utilisé avec
une autre antenne ou un autre émetteur.
CHARGING-THE CHIPS
Charge your Chips®Ultra or Chips®Ultra 2.0 on the
way to the hill, instead of having to plug them in the
night before.
Gently plug the three holes on the side of the Chip
into the three prongs in the charging case.
Be sure to put the Left Chip in the Left side and the
Right Chip in the Right side in the charging case.
The LED lights on both Chips will be RED - (CHARGING).
Once both LEDs go off the Chips are fully charged.
Chips total charging time: About 2 hours